blob: 301945fc8c77d4c46460f16150c26a69c461e3fe [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2017, 2020 NXP
*/
#ifndef __LS1088A_QDS_H
#define __LS1088A_QDS_H
#include "ls1088a_common.h"
#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
unsigned long get_board_ddr_clk(void);
#endif
#ifdef CONFIG_TFABOOT
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_MISC_INIT_R
#else
#if defined(CONFIG_QSPI_BOOT)
#elif defined(CONFIG_SD_BOOT)
#define CONFIG_SYS_MMC_ENV_DEV 0
#endif
#endif
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_QIXIS_I2C_ACCESS
#define SYS_NO_FLASH
#undef CONFIG_CMD_IMLS
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 100000000
#else
#define CONFIG_QIXIS_I2C_ACCESS
#ifndef CONFIG_DM_I2C
#define CONFIG_SYS_I2C_EARLY_INIT
#endif
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
#endif
#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4)
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_DDR_SPD
#define CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS 0x51
#define CONFIG_SYS_SPD_BUS_NUM 0
/*
* IFC Definitions
*/
#if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
#define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024)
#define CONFIG_SYS_NOR0_CSPR \
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CONFIG_SYS_NOR0_CSPR_EARLY \
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CONFIG_SYS_NOR1_CSPR \
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CONFIG_SYS_NOR1_CSPR_EARLY \
(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS_EARLY) | \
CSPR_PORT_SIZE_16 | \
CSPR_MSEL_NOR | \
CSPR_V)
#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12)
#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
FTIM0_NOR_TEADC(0x5) | \
FTIM0_NOR_TAVDS(0x6) | \
FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
FTIM1_NOR_TRAD_NOR(0x1a) | \
FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x8) | \
FTIM2_NOR_TCH(0x8) | \
FTIM2_NOR_TWPH(0xe) | \
FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3 0x04000000
#define CONFIG_SYS_IFC_CCR 0x01000000
#ifndef SYS_NO_FLASH
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\
CONFIG_SYS_FLASH_BASE + 0x40000000}
#endif
#endif
#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_MAX_ECCPOS 256
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_CSPR_EXT (0x0)
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
| CSPR_MSEL_NAND /* MSEL = NAND */ \
| CSPR_V)
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024)
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
| CSOR_NAND_PGS_2K /* Page Size = 2K */ \
| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
FTIM0_NAND_TWP(0x18) | \
FTIM0_NAND_TWCHT(0x07) | \
FTIM0_NAND_TWH(0x0a))
#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
FTIM1_NAND_TWBE(0x39) | \
FTIM1_NAND_TRR(0x0e) | \
FTIM1_NAND_TRP(0x18))
#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
FTIM2_NAND_TREH(0x0a) | \
FTIM2_NAND_TWHRE(0x1e))
#define CONFIG_SYS_NAND_FTIM3 0x0
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_FSL_QIXIS
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
#define QIXIS_LBMAP_SWITCH 6
#define QIXIS_QMAP_MASK 0xe0
#define QIXIS_QMAP_SHIFT 5
#define QIXIS_LBMAP_MASK 0x0f
#define QIXIS_LBMAP_SHIFT 0
#define QIXIS_LBMAP_DFLTBANK 0x0e
#define QIXIS_LBMAP_ALTBANK 0x2e
#define QIXIS_LBMAP_SD 0x00
#define QIXIS_LBMAP_EMMC 0x00
#define QIXIS_LBMAP_IFC 0x00
#define QIXIS_LBMAP_SD_QSPI 0x0e
#define QIXIS_LBMAP_QSPI 0x0e
#define QIXIS_RCW_SRC_IFC 0x25
#define QIXIS_RCW_SRC_SD 0x40
#define QIXIS_RCW_SRC_EMMC 0x41
#define QIXIS_RCW_SRC_QSPI 0x62
#define QIXIS_RST_CTL_RESET 0x41
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
#define QIXIS_RST_FORCE_MEM 0x01
#define QIXIS_STAT_PRES1 0xb
#define QIXIS_SDID_MASK 0x07
#define QIXIS_ESDHC_NO_ADAPTER 0x7
#define CONFIG_SYS_FPGA_CSPR_EXT (0x0)
#define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
| CSPR_PORT_SIZE_8 \
| CSPR_MSEL_GPCM \
| CSPR_V)
#define SYS_FPGA_CSPR_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
| CSPR_PORT_SIZE_8 \
| CSPR_MSEL_GPCM \
| CSPR_V)
#define SYS_FPGA_AMASK IFC_AMASK(64 * 1024)
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(0)
#else
#define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(12)
#endif
/* QIXIS Timing parameters*/
#define SYS_FPGA_CS_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
FTIM0_GPCM_TEADC(0x0e) | \
FTIM0_GPCM_TEAHC(0x0e))
#define SYS_FPGA_CS_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
FTIM1_GPCM_TRAD(0x3f))
#define SYS_FPGA_CS_FTIM2 (FTIM2_GPCM_TCS(0xf) | \
FTIM2_GPCM_TCH(0xf) | \
FTIM2_GPCM_TWP(0x3E))
#define SYS_FPGA_CS_FTIM3 0x0
#ifdef CONFIG_TFABOOT
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR_EARLY
#define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR1_CSPR
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK_EARLY
#define CONFIG_SYS_AMASK1_FINAL CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
#define CONFIG_SYS_CSPR3_FINAL SYS_FPGA_CSPR_FINAL
#define CONFIG_SYS_AMASK3 SYS_FPGA_AMASK
#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR
#define CONFIG_SYS_CS3_FTIM0 SYS_FPGA_CS_FTIM0
#define CONFIG_SYS_CS3_FTIM1 SYS_FPGA_CS_FTIM1
#define CONFIG_SYS_CS3_FTIM2 SYS_FPGA_CS_FTIM2
#define CONFIG_SYS_CS3_FTIM3 SYS_FPGA_CS_FTIM3
#else
#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_FPGA_CSPR_EXT
#define CONFIG_SYS_CSPR2 CONFIG_SYS_FPGA_CSPR
#define CONFIG_SYS_CSPR2_FINAL SYS_FPGA_CSPR_FINAL
#define CONFIG_SYS_AMASK2 SYS_FPGA_AMASK
#define CONFIG_SYS_CSOR2 CONFIG_SYS_FPGA_CSOR
#define CONFIG_SYS_CS2_FTIM0 SYS_FPGA_CS_FTIM0
#define CONFIG_SYS_CS2_FTIM1 SYS_FPGA_CS_FTIM1
#define CONFIG_SYS_CS2_FTIM2 SYS_FPGA_CS_FTIM2
#define CONFIG_SYS_CS2_FTIM3 SYS_FPGA_CS_FTIM3
#else
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY
#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR_EARLY
#define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR1_CSPR
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK_EARLY
#define CONFIG_SYS_AMASK1_FINAL CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT
#define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR
#define CONFIG_SYS_CSPR3_FINAL SYS_FPGA_CSPR_FINAL
#define CONFIG_SYS_AMASK3 SYS_FPGA_AMASK
#define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR
#define CONFIG_SYS_CS3_FTIM0 SYS_FPGA_CS_FTIM0
#define CONFIG_SYS_CS3_FTIM1 SYS_FPGA_CS_FTIM1
#define CONFIG_SYS_CS3_FTIM2 SYS_FPGA_CS_FTIM2
#define CONFIG_SYS_CS3_FTIM3 SYS_FPGA_CS_FTIM3
#endif
#endif
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
/*
* I2C bus multiplexer
*/
#define I2C_MUX_PCA_ADDR_PRI 0x77
#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
#define I2C_RETIMER_ADDR 0x18
#define I2C_RETIMER_ADDR2 0x19
#define I2C_MUX_CH_DEFAULT 0x8
#define I2C_MUX_CH5 0xD
#define I2C_MUX_CH_VOL_MONITOR 0xA
/* Voltage monitor on channel 2*/
#define I2C_VOL_MONITOR_ADDR 0x63
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
#define I2C_SVDD_MONITOR_ADDR 0x4F
#define CONFIG_VID_FLS_ENV "ls1088aqds_vdd_mv"
#define CONFIG_VID
/* The lowest and highest voltage allowed for LS1088AQDS */
#define VDD_MV_MIN 819
#define VDD_MV_MAX 1212
#define CONFIG_VOL_MONITOR_LTC3882_SET
#define CONFIG_VOL_MONITOR_LTC3882_READ
/* PM Bus commands code for LTC3882*/
#define PMBUS_CMD_PAGE 0x0
#define PMBUS_CMD_READ_VOUT 0x8B
#define PMBUS_CMD_PAGE_PLUS_WRITE 0x05
#define PMBUS_CMD_VOUT_COMMAND 0x21
#define PWM_CHANNEL0 0x0
/*
* RTC configuration
*/
#define RTC
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
/* QSPI device */
#if defined(CONFIG_TFABOOT) || \
defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
#define FSL_QSPI_FLASH_SIZE (1 << 26)
#define FSL_QSPI_FLASH_NUM 2
#endif
#ifdef CONFIG_FSL_DSPI
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_SPI_FLASH_SST
#define CONFIG_SPI_FLASH_EON
#if !defined(CONFIG_TFABOOT) && \
!defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI)
#endif
#endif
#define CONFIG_CMD_MEMINFO
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#endif
#define CONFIG_FSL_MEMAC
/* MMC */
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#define CONFIG_ESDHC_DETECT_QUIRK ((readb(QIXIS_BASE + QIXIS_STAT_PRES1) & \
QIXIS_SDID_MASK) != QIXIS_ESDHC_NO_ADAPTER)
/* Initial environment variables */
#ifdef CONFIG_NXP_ESBC
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x90100000\0" \
"kernel_addr=0x100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x1000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"mcinitcmd=sf probe 0:0;sf read 0xa0a00000 0xa00000 0x100000;" \
"sf read 0xa0640000 0x640000 0x4000; esbc_validate 0xa0640000;" \
"sf read 0xa0e00000 0xe00000 0x100000;" \
"sf read 0xa0680000 0x680000 0x4000;esbc_validate 0xa0680000;" \
"fsl_mc start mc 0xa0a00000 0xa0e00000\0" \
"mcmemsize=0x70000000 \0"
#else /* if !(CONFIG_NXP_ESBC) */
#ifdef CONFIG_TFABOOT
#define QSPI_MC_INIT_CMD \
"sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
"sf read 0x80100000 0xE00000 0x100000;" \
"fsl_mc start mc 0x80000000 0x80100000\0"
#define SD_MC_INIT_CMD \
"mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
"mmc read 0x80100000 0x7000 0x800;" \
"fsl_mc start mc 0x80000000 0x80100000\0"
#define IFC_MC_INIT_CMD \
"fsl_mc start mc 0x580A00000 0x580E00000\0"
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x90100000\0" \
"kernel_addr=0x100000\0" \
"kernel_addr_sd=0x800\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x1000000\0" \
"kernel_start_sd=0x8000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernel_size_sd=0x14000\0" \
"mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
"sf read 0x80100000 0xE00000 0x100000;" \
"fsl_mc start mc 0x80000000 0x80100000\0" \
"mcmemsize=0x70000000 \0" \
"BOARD=ls1088aqds\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
BOOTENV \
"boot_scripts=ls1088aqds_boot.scr\0" \
"boot_script_hdr=hdr_ls1088aqds_bs.out\0" \
"scan_dev_for_boot_part=" \
"part list ${devtype} ${devnum} devplist; " \
"env exists devplist || setenv devplist 1; " \
"for distro_bootpart in ${devplist}; do " \
"if fstype ${devtype} " \
"${devnum}:${distro_bootpart} " \
"bootfstype; then " \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
"env exists secureboot && load ${devtype} " \
"${devnum}:${distro_bootpart} " \
"${scripthdraddr} ${prefix}${boot_script_hdr}; "\
"env exists secureboot " \
"&& esbc_validate ${scripthdraddr};" \
"source ${scriptaddr}\0" \
"qspi_bootcmd=echo Trying load from qspi..; " \
"sf probe 0:0; " \
"sf read 0x80001000 0xd00000 0x100000; " \
"fsl_mc lazyapply dpl 0x80001000 && " \
"sf read $kernel_load $kernel_start " \
"$kernel_size && bootm $kernel_load#$BOARD\0" \
"sd_bootcmd=echo Trying load from sd card..; " \
"mmcinfo;mmc read 0x80001000 0x6800 0x800; "\
"fsl_mc lazyapply dpl 0x80001000 && " \
"mmc read $kernel_load $kernel_start_sd " \
"$kernel_size_sd && bootm $kernel_load#$BOARD\0" \
"nor_bootcmd=echo Trying load from nor..; " \
"fsl_mc lazyapply dpl 0x580d00000 && " \
"cp.b $kernel_start $kernel_load " \
"$kernel_size && bootm $kernel_load#$BOARD\0"
#else
#if defined(CONFIG_QSPI_BOOT)
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x90100000\0" \
"kernel_addr=0x100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x1000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \
"sf read 0x80100000 0xE00000 0x100000;" \
"fsl_mc start mc 0x80000000 0x80100000\0" \
"mcmemsize=0x70000000 \0"
#elif defined(CONFIG_SD_BOOT)
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x90100000\0" \
"kernel_addr=0x800\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x8000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x14000\0" \
"mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \
"mmc read 0x80100000 0x7000 0x800;" \
"fsl_mc start mc 0x80000000 0x80100000\0" \
"mcmemsize=0x70000000 \0"
#else /* NOR BOOT */
#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x90100000\0" \
"kernel_addr=0x100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x1000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"mcinitcmd=fsl_mc start mc 0x580A00000 0x580E00000\0" \
"mcmemsize=0x70000000 \0"
#endif
#endif /* CONFIG_TFABOOT */
#endif /* CONFIG_NXP_ESBC */
#ifdef CONFIG_TFABOOT
#define QSPI_NOR_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; " \
"env exists secureboot && esbc_halt;;"
#define IFC_NOR_BOOTCOMMAND "run distro_bootcmd; run nor_bootcmd; " \
"env exists secureboot && esbc_halt;;"
#define SD_BOOTCOMMAND "run distro_bootcmd; run sd_bootcmd; " \
"env exists secureboot && esbc_halt;;"
#endif
#ifdef CONFIG_FSL_MC_ENET
#define CONFIG_FSL_MEMAC
#define RGMII_PHY1_ADDR 0x1
#define RGMII_PHY2_ADDR 0x2
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
#define SGMII_CARD_PORT2_PHY_ADDR 0x1d
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
#define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0
#define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1
#define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2
#define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3
#define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4
#define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5
#define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6
#define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7
#define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8
#define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9
#define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa
#define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb
#define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc
#define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd
#define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe
#define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf
#define CONFIG_ETHPRIME "DPMAC1@xgmii"
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
#endif
#define BOOT_TARGET_DEVICES(func) \
func(USB, usb, 0) \
func(MMC, mmc, 0) \
func(SCSI, scsi, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#include <asm/fsl_secure_boot.h>
#endif /* __LS1088A_QDS_H */