| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2020-2021 Broadcom |
| * |
| */ |
| |
| #include <common.h> |
| #include <dm.h> |
| #include <errno.h> |
| #include <generic-phy.h> |
| #include <pci.h> |
| #include <malloc.h> |
| #include <asm/io.h> |
| #include <dm/device_compat.h> |
| #include <linux/delay.h> |
| #include <linux/log2.h> |
| |
| #define EP_PERST_SOURCE_SELECT_SHIFT 2 |
| #define EP_PERST_SOURCE_SELECT BIT(EP_PERST_SOURCE_SELECT_SHIFT) |
| #define EP_MODE_SURVIVE_PERST_SHIFT 1 |
| #define EP_MODE_SURVIVE_PERST BIT(EP_MODE_SURVIVE_PERST_SHIFT) |
| #define RC_PCIE_RST_OUTPUT_SHIFT 0 |
| #define RC_PCIE_RST_OUTPUT BIT(RC_PCIE_RST_OUTPUT_SHIFT) |
| |
| #define CFG_IND_ADDR_MASK 0x00001ffc |
| |
| #define CFG_ADDR_CFG_ECAM_MASK 0xfffffffc |
| #define CFG_ADDR_CFG_TYPE_MASK 0x00000003 |
| |
| #define IPROC_PCI_PM_CAP 0x48 |
| #define IPROC_PCI_PM_CAP_MASK 0xffff |
| #define IPROC_PCI_EXP_CAP 0xac |
| |
| #define IPROC_PCIE_REG_INVALID 0xffff |
| |
| #define PCI_EXP_TYPE_ROOT_PORT 0x4 /* Root Port */ |
| #define PCI_EXP_RTCTL 28 /* Root Control */ |
| /* CRS Software Visibility capability */ |
| #define PCI_EXP_RTCAP_CRSVIS 0x0001 |
| |
| #define PCI_EXP_LNKSTA 18 /* Link Status */ |
| #define PCI_EXP_LNKSTA_NLW 0x03f0 /* Negotiated Link Width */ |
| |
| #define PCIE_PHYLINKUP_SHIFT 3 |
| #define PCIE_PHYLINKUP BIT(PCIE_PHYLINKUP_SHIFT) |
| #define PCIE_DL_ACTIVE_SHIFT 2 |
| #define PCIE_DL_ACTIVE BIT(PCIE_DL_ACTIVE_SHIFT) |
| |
| /* derive the enum index of the outbound/inbound mapping registers */ |
| #define MAP_REG(base_reg, index) ((base_reg) + (index) * 2) |
| |
| /* |
| * Maximum number of outbound mapping window sizes that can be supported by any |
| * OARR/OMAP mapping pair |
| */ |
| #define MAX_NUM_OB_WINDOW_SIZES 4 |
| |
| #define OARR_VALID_SHIFT 0 |
| #define OARR_VALID BIT(OARR_VALID_SHIFT) |
| #define OARR_SIZE_CFG_SHIFT 1 |
| |
| /* |
| * Maximum number of inbound mapping region sizes that can be supported by an |
| * IARR |
| */ |
| #define MAX_NUM_IB_REGION_SIZES 9 |
| |
| #define IMAP_VALID_SHIFT 0 |
| #define IMAP_VALID BIT(IMAP_VALID_SHIFT) |
| |
| #define APB_ERR_EN_SHIFT 0 |
| #define APB_ERR_EN BIT(APB_ERR_EN_SHIFT) |
| |
| /** |
| * iProc PCIe host registers |
| */ |
| enum iproc_pcie_reg { |
| /* clock/reset signal control */ |
| IPROC_PCIE_CLK_CTRL = 0, |
| |
| /* |
| * To allow MSI to be steered to an external MSI controller (e.g., ARM |
| * GICv3 ITS) |
| */ |
| IPROC_PCIE_MSI_GIC_MODE, |
| |
| /* |
| * IPROC_PCIE_MSI_BASE_ADDR and IPROC_PCIE_MSI_WINDOW_SIZE define the |
| * window where the MSI posted writes are written, for the writes to be |
| * interpreted as MSI writes. |
| */ |
| IPROC_PCIE_MSI_BASE_ADDR, |
| IPROC_PCIE_MSI_WINDOW_SIZE, |
| |
| /* |
| * To hold the address of the register where the MSI writes are |
| * programed. When ARM GICv3 ITS is used, this should be programmed |
| * with the address of the GITS_TRANSLATER register. |
| */ |
| IPROC_PCIE_MSI_ADDR_LO, |
| IPROC_PCIE_MSI_ADDR_HI, |
| |
| /* enable MSI */ |
| IPROC_PCIE_MSI_EN_CFG, |
| |
| /* allow access to root complex configuration space */ |
| IPROC_PCIE_CFG_IND_ADDR, |
| IPROC_PCIE_CFG_IND_DATA, |
| |
| /* allow access to device configuration space */ |
| IPROC_PCIE_CFG_ADDR, |
| IPROC_PCIE_CFG_DATA, |
| |
| /* enable INTx */ |
| IPROC_PCIE_INTX_EN, |
| IPROC_PCIE_INTX_CSR, |
| |
| /* outbound address mapping */ |
| IPROC_PCIE_OARR0, |
| IPROC_PCIE_OMAP0, |
| IPROC_PCIE_OARR1, |
| IPROC_PCIE_OMAP1, |
| IPROC_PCIE_OARR2, |
| IPROC_PCIE_OMAP2, |
| IPROC_PCIE_OARR3, |
| IPROC_PCIE_OMAP3, |
| |
| /* inbound address mapping */ |
| IPROC_PCIE_IARR0, |
| IPROC_PCIE_IMAP0, |
| IPROC_PCIE_IARR1, |
| IPROC_PCIE_IMAP1, |
| IPROC_PCIE_IARR2, |
| IPROC_PCIE_IMAP2, |
| IPROC_PCIE_IARR3, |
| IPROC_PCIE_IMAP3, |
| IPROC_PCIE_IARR4, |
| IPROC_PCIE_IMAP4, |
| |
| /* config read status */ |
| IPROC_PCIE_CFG_RD_STATUS, |
| |
| /* link status */ |
| IPROC_PCIE_LINK_STATUS, |
| |
| /* enable APB error for unsupported requests */ |
| IPROC_PCIE_APB_ERR_EN, |
| |
| /* Ordering Mode configuration registers */ |
| IPROC_PCIE_ORDERING_CFG, |
| IPROC_PCIE_IMAP0_RO_CONTROL, |
| IPROC_PCIE_IMAP1_RO_CONTROL, |
| IPROC_PCIE_IMAP2_RO_CONTROL, |
| IPROC_PCIE_IMAP3_RO_CONTROL, |
| IPROC_PCIE_IMAP4_RO_CONTROL, |
| |
| /* total number of core registers */ |
| IPROC_PCIE_MAX_NUM_REG, |
| }; |
| |
| /* iProc PCIe PAXB v2 registers */ |
| static const u16 iproc_pcie_reg_paxb_v2[] = { |
| [IPROC_PCIE_CLK_CTRL] = 0x000, |
| [IPROC_PCIE_CFG_IND_ADDR] = 0x120, |
| [IPROC_PCIE_CFG_IND_DATA] = 0x124, |
| [IPROC_PCIE_CFG_ADDR] = 0x1f8, |
| [IPROC_PCIE_CFG_DATA] = 0x1fc, |
| [IPROC_PCIE_INTX_EN] = 0x330, |
| [IPROC_PCIE_INTX_CSR] = 0x334, |
| [IPROC_PCIE_OARR0] = 0xd20, |
| [IPROC_PCIE_OMAP0] = 0xd40, |
| [IPROC_PCIE_OARR1] = 0xd28, |
| [IPROC_PCIE_OMAP1] = 0xd48, |
| [IPROC_PCIE_OARR2] = 0xd60, |
| [IPROC_PCIE_OMAP2] = 0xd68, |
| [IPROC_PCIE_OARR3] = 0xdf0, |
| [IPROC_PCIE_OMAP3] = 0xdf8, |
| [IPROC_PCIE_IARR0] = 0xd00, |
| [IPROC_PCIE_IMAP0] = 0xc00, |
| [IPROC_PCIE_IARR2] = 0xd10, |
| [IPROC_PCIE_IMAP2] = 0xcc0, |
| [IPROC_PCIE_IARR3] = 0xe00, |
| [IPROC_PCIE_IMAP3] = 0xe08, |
| [IPROC_PCIE_IARR4] = 0xe68, |
| [IPROC_PCIE_IMAP4] = 0xe70, |
| [IPROC_PCIE_CFG_RD_STATUS] = 0xee0, |
| [IPROC_PCIE_LINK_STATUS] = 0xf0c, |
| [IPROC_PCIE_APB_ERR_EN] = 0xf40, |
| [IPROC_PCIE_ORDERING_CFG] = 0x2000, |
| [IPROC_PCIE_IMAP0_RO_CONTROL] = 0x201c, |
| [IPROC_PCIE_IMAP1_RO_CONTROL] = 0x2020, |
| [IPROC_PCIE_IMAP2_RO_CONTROL] = 0x2024, |
| [IPROC_PCIE_IMAP3_RO_CONTROL] = 0x2028, |
| [IPROC_PCIE_IMAP4_RO_CONTROL] = 0x202c, |
| }; |
| |
| /* iProc PCIe PAXC v2 registers */ |
| static const u16 iproc_pcie_reg_paxc_v2[] = { |
| [IPROC_PCIE_MSI_GIC_MODE] = 0x050, |
| [IPROC_PCIE_MSI_BASE_ADDR] = 0x074, |
| [IPROC_PCIE_MSI_WINDOW_SIZE] = 0x078, |
| [IPROC_PCIE_MSI_ADDR_LO] = 0x07c, |
| [IPROC_PCIE_MSI_ADDR_HI] = 0x080, |
| [IPROC_PCIE_MSI_EN_CFG] = 0x09c, |
| [IPROC_PCIE_CFG_IND_ADDR] = 0x1f0, |
| [IPROC_PCIE_CFG_IND_DATA] = 0x1f4, |
| [IPROC_PCIE_CFG_ADDR] = 0x1f8, |
| [IPROC_PCIE_CFG_DATA] = 0x1fc, |
| }; |
| |
| /** |
| * List of device IDs of controllers that have corrupted |
| * capability list that require SW fixup |
| */ |
| static const u16 iproc_pcie_corrupt_cap_did[] = { |
| 0x16cd, |
| 0x16f0, |
| 0xd802, |
| 0xd804 |
| }; |
| |
| enum iproc_pcie_type { |
| IPROC_PCIE_PAXB_V2, |
| IPROC_PCIE_PAXC, |
| IPROC_PCIE_PAXC_V2, |
| }; |
| |
| /** |
| * struct iproc_pcie_ob - iProc PCIe outbound mapping |
| * |
| * @axi_offset: offset from the AXI address to the internal address used by |
| * the iProc PCIe core |
| * @nr_windows: total number of supported outbound mapping windows |
| */ |
| struct iproc_pcie_ob { |
| resource_size_t axi_offset; |
| unsigned int nr_windows; |
| }; |
| |
| /** |
| * struct iproc_pcie_ib - iProc PCIe inbound mapping |
| * |
| * @nr_regions: total number of supported inbound mapping regions |
| */ |
| struct iproc_pcie_ib { |
| unsigned int nr_regions; |
| }; |
| |
| /** |
| * struct iproc_pcie_ob_map - outbound mapping controller specific parameters |
| * |
| * @window_sizes: list of supported outbound mapping window sizes in MB |
| * @nr_sizes: number of supported outbound mapping window sizes |
| */ |
| struct iproc_pcie_ob_map { |
| resource_size_t window_sizes[MAX_NUM_OB_WINDOW_SIZES]; |
| unsigned int nr_sizes; |
| }; |
| |
| static const struct iproc_pcie_ob_map paxb_v2_ob_map[] = { |
| { |
| /* OARR0/OMAP0 */ |
| .window_sizes = { 128, 256 }, |
| .nr_sizes = 2, |
| }, |
| { |
| /* OARR1/OMAP1 */ |
| .window_sizes = { 128, 256 }, |
| .nr_sizes = 2, |
| }, |
| { |
| /* OARR2/OMAP2 */ |
| .window_sizes = { 128, 256, 512, 1024 }, |
| .nr_sizes = 4, |
| }, |
| { |
| /* OARR3/OMAP3 */ |
| .window_sizes = { 128, 256, 512, 1024 }, |
| .nr_sizes = 4, |
| }, |
| }; |
| |
| /** |
| * iProc PCIe inbound mapping type |
| */ |
| enum iproc_pcie_ib_map_type { |
| /* for DDR memory */ |
| IPROC_PCIE_IB_MAP_MEM = 0, |
| |
| /* for device I/O memory */ |
| IPROC_PCIE_IB_MAP_IO, |
| |
| /* invalid or unused */ |
| IPROC_PCIE_IB_MAP_INVALID |
| }; |
| |
| /** |
| * struct iproc_pcie_ib_map - inbound mapping controller specific parameters |
| * |
| * @type: inbound mapping region type |
| * @size_unit: inbound mapping region size unit, could be SZ_1K, SZ_1M, or SZ_1G |
| * @region_sizes: list of supported inbound mapping region sizes in KB, MB, or |
| * GB, depedning on the size unit |
| * @nr_sizes: number of supported inbound mapping region sizes |
| * @nr_windows: number of supported inbound mapping windows for the region |
| * @imap_addr_offset: register offset between the upper and lower 32-bit |
| * IMAP address registers |
| * @imap_window_offset: register offset between each IMAP window |
| */ |
| struct iproc_pcie_ib_map { |
| enum iproc_pcie_ib_map_type type; |
| unsigned int size_unit; |
| resource_size_t region_sizes[MAX_NUM_IB_REGION_SIZES]; |
| unsigned int nr_sizes; |
| unsigned int nr_windows; |
| u16 imap_addr_offset; |
| u16 imap_window_offset; |
| }; |
| |
| static const struct iproc_pcie_ib_map paxb_v2_ib_map[] = { |
| { |
| /* IARR0/IMAP0 */ |
| .type = IPROC_PCIE_IB_MAP_IO, |
| .size_unit = SZ_1K, |
| .region_sizes = { 32 }, |
| .nr_sizes = 1, |
| .nr_windows = 8, |
| .imap_addr_offset = 0x40, |
| .imap_window_offset = 0x4, |
| }, |
| { |
| /* IARR1/IMAP1 (currently unused) */ |
| .type = IPROC_PCIE_IB_MAP_INVALID, |
| }, |
| { |
| /* IARR2/IMAP2 */ |
| .type = IPROC_PCIE_IB_MAP_MEM, |
| .size_unit = SZ_1M, |
| .region_sizes = { 64, 128, 256, 512, 1024, 2048, 4096, 8192, |
| 16384 }, |
| .nr_sizes = 9, |
| .nr_windows = 1, |
| .imap_addr_offset = 0x4, |
| .imap_window_offset = 0x8, |
| }, |
| { |
| /* IARR3/IMAP3 */ |
| .type = IPROC_PCIE_IB_MAP_MEM, |
| .size_unit = SZ_1G, |
| .region_sizes = { 1, 2, 4, 8, 16, 32 }, |
| .nr_sizes = 6, |
| .nr_windows = 8, |
| .imap_addr_offset = 0x4, |
| .imap_window_offset = 0x8, |
| }, |
| { |
| /* IARR4/IMAP4 */ |
| .type = IPROC_PCIE_IB_MAP_MEM, |
| .size_unit = SZ_1G, |
| .region_sizes = { 32, 64, 128, 256, 512 }, |
| .nr_sizes = 5, |
| .nr_windows = 8, |
| .imap_addr_offset = 0x4, |
| .imap_window_offset = 0x8, |
| }, |
| }; |
| |
| /** |
| * struct iproc_pcie - iproc pcie device instance |
| * |
| * @dev: pointer to pcie udevice |
| * @base: device I/O base address |
| * @type: pci device type, PAXC or PAXB |
| * @reg_offsets: pointer to pcie host register |
| * @fix_paxc_cap: paxc capability |
| * @need_ob_cfg: outbound mapping status |
| * @ob: pcie outbound mapping |
| * @ob_map: pointer to outbound mapping parameters |
| * @need_ib_cfg: inbound mapping status |
| * @ib: pcie inbound mapping |
| * @ib_map: pointer to inbound mapping parameters |
| * @ep_is_internal: ep status |
| * @phy: phy device |
| * @link_is_active: link up status |
| * @has_apb_err_disable: apb error status |
| */ |
| struct iproc_pcie { |
| struct udevice *dev; |
| void __iomem *base; |
| enum iproc_pcie_type type; |
| u16 *reg_offsets; |
| bool fix_paxc_cap; |
| bool need_ob_cfg; |
| struct iproc_pcie_ob ob; |
| const struct iproc_pcie_ob_map *ob_map; |
| bool need_ib_cfg; |
| struct iproc_pcie_ib ib; |
| const struct iproc_pcie_ib_map *ib_map; |
| bool ep_is_internal; |
| struct phy phy; |
| bool link_is_active; |
| bool has_apb_err_disable; |
| }; |
| |
| static inline bool iproc_pcie_reg_is_invalid(u16 reg_offset) |
| { |
| return !!(reg_offset == IPROC_PCIE_REG_INVALID); |
| } |
| |
| static inline u16 iproc_pcie_reg_offset(struct iproc_pcie *pcie, |
| enum iproc_pcie_reg reg) |
| { |
| return pcie->reg_offsets[reg]; |
| } |
| |
| static inline u32 iproc_pcie_read_reg(struct iproc_pcie *pcie, |
| enum iproc_pcie_reg reg) |
| { |
| u16 offset = iproc_pcie_reg_offset(pcie, reg); |
| |
| if (iproc_pcie_reg_is_invalid(offset)) |
| return 0; |
| |
| return readl(pcie->base + offset); |
| } |
| |
| static inline void iproc_pcie_write_reg(struct iproc_pcie *pcie, |
| enum iproc_pcie_reg reg, u32 val) |
| { |
| u16 offset = iproc_pcie_reg_offset(pcie, reg); |
| |
| if (iproc_pcie_reg_is_invalid(offset)) |
| return; |
| |
| writel(val, pcie->base + offset); |
| } |
| |
| static int iproc_pcie_map_ep_cfg_reg(const struct udevice *udev, pci_dev_t bdf, |
| uint where, void **paddress) |
| { |
| struct iproc_pcie *pcie = dev_get_priv(udev); |
| unsigned int busno = PCI_BUS(bdf); |
| unsigned int slot = PCI_DEV(bdf); |
| unsigned int fn = PCI_FUNC(bdf); |
| |
| u16 offset; |
| u32 val; |
| |
| /* root complex access */ |
| if (busno == 0) { |
| if (slot > 0 || fn > 0) |
| return -ENODEV; |
| |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_CFG_IND_ADDR, |
| where & CFG_IND_ADDR_MASK); |
| offset = iproc_pcie_reg_offset(pcie, IPROC_PCIE_CFG_IND_DATA); |
| if (iproc_pcie_reg_is_invalid(offset)) |
| return -ENODEV; |
| |
| *paddress = (pcie->base + offset); |
| return 0; |
| } |
| |
| if (!pcie->link_is_active) |
| return -ENODEV; |
| |
| /* EP device access */ |
| val = (PCIE_ECAM_OFFSET(busno, slot, fn, where) & CFG_ADDR_CFG_ECAM_MASK) |
| | (1 & CFG_ADDR_CFG_TYPE_MASK); |
| |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_CFG_ADDR, val); |
| offset = iproc_pcie_reg_offset(pcie, IPROC_PCIE_CFG_DATA); |
| |
| if (iproc_pcie_reg_is_invalid(offset)) |
| return -ENODEV; |
| |
| *paddress = (pcie->base + offset); |
| |
| return 0; |
| } |
| |
| static void iproc_pcie_fix_cap(struct iproc_pcie *pcie, int where, ulong *val) |
| { |
| u32 i, dev_id; |
| |
| switch (where & ~0x3) { |
| case PCI_VENDOR_ID: |
| dev_id = *val >> 16; |
| |
| /* |
| * Activate fixup for those controllers that have corrupted |
| * capability list registers |
| */ |
| for (i = 0; i < ARRAY_SIZE(iproc_pcie_corrupt_cap_did); i++) |
| if (dev_id == iproc_pcie_corrupt_cap_did[i]) |
| pcie->fix_paxc_cap = true; |
| break; |
| |
| case IPROC_PCI_PM_CAP: |
| if (pcie->fix_paxc_cap) { |
| /* advertise PM, force next capability to PCIe */ |
| *val &= ~IPROC_PCI_PM_CAP_MASK; |
| *val |= IPROC_PCI_EXP_CAP << 8 | PCI_CAP_ID_PM; |
| } |
| break; |
| |
| case IPROC_PCI_EXP_CAP: |
| if (pcie->fix_paxc_cap) { |
| /* advertise root port, version 2, terminate here */ |
| *val = (PCI_EXP_TYPE_ROOT_PORT << 4 | 2) << 16 | |
| PCI_CAP_ID_EXP; |
| } |
| break; |
| |
| case IPROC_PCI_EXP_CAP + PCI_EXP_RTCTL: |
| /* Don't advertise CRS SV support */ |
| *val &= ~(PCI_EXP_RTCAP_CRSVIS << 16); |
| break; |
| |
| default: |
| break; |
| } |
| } |
| |
| static int iproc_pci_raw_config_read32(struct iproc_pcie *pcie, |
| unsigned int devfn, int where, |
| int size, u32 *val) |
| { |
| void __iomem *addr; |
| int ret; |
| |
| ret = iproc_pcie_map_ep_cfg_reg(pcie->dev, devfn, where & ~0x3, &addr); |
| if (ret) { |
| *val = ~0; |
| return -EINVAL; |
| } |
| |
| *val = readl(addr); |
| |
| if (size <= 2) |
| *val = (*val >> (8 * (where & 3))) & ((1 << (size * 8)) - 1); |
| |
| return 0; |
| } |
| |
| static int iproc_pci_raw_config_write32(struct iproc_pcie *pcie, |
| unsigned int devfn, int where, |
| int size, u32 val) |
| { |
| void __iomem *addr; |
| int ret; |
| u32 mask, tmp; |
| |
| ret = iproc_pcie_map_ep_cfg_reg(pcie->dev, devfn, where & ~0x3, &addr); |
| if (ret) |
| return -EINVAL; |
| |
| if (size == 4) { |
| writel(val, addr); |
| return 0; |
| } |
| |
| mask = ~(((1 << (size * 8)) - 1) << ((where & 0x3) * 8)); |
| tmp = readl(addr) & mask; |
| tmp |= val << ((where & 0x3) * 8); |
| writel(tmp, addr); |
| return 0; |
| } |
| |
| /** |
| * iproc_pcie_apb_err_disable() - configure apb error |
| * |
| * APB error forwarding can be disabled during access of configuration |
| * registers of the endpoint device, to prevent unsupported requests |
| * (typically seen during enumeration with multi-function devices) from |
| * triggering a system exception. |
| * |
| * @bus: pcie udevice |
| * @bdf: pdf value |
| * @disabled: flag to enable/disabled apb error |
| */ |
| static inline void iproc_pcie_apb_err_disable(const struct udevice *bus, |
| pci_dev_t bdf, bool disable) |
| { |
| struct iproc_pcie *pcie = dev_get_priv(bus); |
| u32 val; |
| |
| if (PCI_BUS(bdf) && pcie->has_apb_err_disable) { |
| val = iproc_pcie_read_reg(pcie, IPROC_PCIE_APB_ERR_EN); |
| if (disable) |
| val &= ~APB_ERR_EN; |
| else |
| val |= APB_ERR_EN; |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_APB_ERR_EN, val); |
| } |
| } |
| |
| static int iproc_pcie_config_read32(const struct udevice *bus, pci_dev_t bdf, |
| uint offset, ulong *valuep, |
| enum pci_size_t size) |
| { |
| struct iproc_pcie *pcie = dev_get_priv(bus); |
| int ret; |
| ulong data; |
| |
| iproc_pcie_apb_err_disable(bus, bdf, true); |
| ret = pci_generic_mmap_read_config(bus, iproc_pcie_map_ep_cfg_reg, |
| bdf, offset, &data, PCI_SIZE_32); |
| iproc_pcie_apb_err_disable(bus, bdf, false); |
| if (size <= PCI_SIZE_16) |
| *valuep = (data >> (8 * (offset & 3))) & |
| ((1 << (BIT(size) * 8)) - 1); |
| else |
| *valuep = data; |
| |
| if (!ret && PCI_BUS(bdf) == 0) |
| iproc_pcie_fix_cap(pcie, offset, valuep); |
| |
| return ret; |
| } |
| |
| static int iproc_pcie_config_write32(struct udevice *bus, pci_dev_t bdf, |
| uint offset, ulong value, |
| enum pci_size_t size) |
| { |
| void *addr; |
| ulong mask, tmp; |
| int ret; |
| |
| ret = iproc_pcie_map_ep_cfg_reg(bus, bdf, offset, &addr); |
| if (ret) |
| return ret; |
| |
| if (size == PCI_SIZE_32) { |
| writel(value, addr); |
| return ret; |
| } |
| |
| iproc_pcie_apb_err_disable(bus, bdf, true); |
| mask = ~(((1 << (BIT(size) * 8)) - 1) << ((offset & 0x3) * 8)); |
| tmp = readl(addr) & mask; |
| tmp |= (value << ((offset & 0x3) * 8)); |
| writel(tmp, addr); |
| iproc_pcie_apb_err_disable(bus, bdf, false); |
| |
| return ret; |
| } |
| |
| const static struct dm_pci_ops iproc_pcie_ops = { |
| .read_config = iproc_pcie_config_read32, |
| .write_config = iproc_pcie_config_write32, |
| }; |
| |
| static int iproc_pcie_rev_init(struct iproc_pcie *pcie) |
| { |
| unsigned int reg_idx; |
| const u16 *regs; |
| u16 num_elements; |
| |
| switch (pcie->type) { |
| case IPROC_PCIE_PAXC_V2: |
| pcie->ep_is_internal = true; |
| regs = iproc_pcie_reg_paxc_v2; |
| num_elements = ARRAY_SIZE(iproc_pcie_reg_paxc_v2); |
| break; |
| case IPROC_PCIE_PAXB_V2: |
| regs = iproc_pcie_reg_paxb_v2; |
| num_elements = ARRAY_SIZE(iproc_pcie_reg_paxb_v2); |
| pcie->has_apb_err_disable = true; |
| if (pcie->need_ob_cfg) { |
| pcie->ob.axi_offset = 0; |
| pcie->ob_map = paxb_v2_ob_map; |
| pcie->ob.nr_windows = ARRAY_SIZE(paxb_v2_ob_map); |
| } |
| pcie->need_ib_cfg = true; |
| pcie->ib.nr_regions = ARRAY_SIZE(paxb_v2_ib_map); |
| pcie->ib_map = paxb_v2_ib_map; |
| break; |
| default: |
| dev_dbg(pcie->dev, "incompatible iProc PCIe interface\n"); |
| return -EINVAL; |
| } |
| |
| pcie->reg_offsets = calloc(IPROC_PCIE_MAX_NUM_REG, |
| sizeof(*pcie->reg_offsets)); |
| if (!pcie->reg_offsets) |
| return -ENOMEM; |
| |
| /* go through the register table and populate all valid registers */ |
| pcie->reg_offsets[0] = (pcie->type == IPROC_PCIE_PAXC_V2) ? |
| IPROC_PCIE_REG_INVALID : regs[0]; |
| for (reg_idx = 1; reg_idx < num_elements; reg_idx++) |
| pcie->reg_offsets[reg_idx] = regs[reg_idx] ? |
| regs[reg_idx] : IPROC_PCIE_REG_INVALID; |
| |
| return 0; |
| } |
| |
| static inline bool iproc_pcie_ob_is_valid(struct iproc_pcie *pcie, |
| int window_idx) |
| { |
| u32 val; |
| |
| val = iproc_pcie_read_reg(pcie, MAP_REG(IPROC_PCIE_OARR0, window_idx)); |
| |
| return !!(val & OARR_VALID); |
| } |
| |
| static inline int iproc_pcie_ob_write(struct iproc_pcie *pcie, int window_idx, |
| int size_idx, u64 axi_addr, u64 pci_addr) |
| { |
| u16 oarr_offset, omap_offset; |
| |
| /* |
| * Derive the OARR/OMAP offset from the first pair (OARR0/OMAP0) based |
| * on window index. |
| */ |
| oarr_offset = iproc_pcie_reg_offset(pcie, MAP_REG(IPROC_PCIE_OARR0, |
| window_idx)); |
| omap_offset = iproc_pcie_reg_offset(pcie, MAP_REG(IPROC_PCIE_OMAP0, |
| window_idx)); |
| if (iproc_pcie_reg_is_invalid(oarr_offset) || |
| iproc_pcie_reg_is_invalid(omap_offset)) |
| return -EINVAL; |
| |
| /* |
| * Program the OARR registers. The upper 32-bit OARR register is |
| * always right after the lower 32-bit OARR register. |
| */ |
| writel(lower_32_bits(axi_addr) | (size_idx << OARR_SIZE_CFG_SHIFT) | |
| OARR_VALID, pcie->base + oarr_offset); |
| writel(upper_32_bits(axi_addr), pcie->base + oarr_offset + 4); |
| |
| /* now program the OMAP registers */ |
| writel(lower_32_bits(pci_addr), pcie->base + omap_offset); |
| writel(upper_32_bits(pci_addr), pcie->base + omap_offset + 4); |
| |
| debug("ob window [%d]: offset 0x%x axi %pap pci %pap\n", |
| window_idx, oarr_offset, &axi_addr, &pci_addr); |
| debug("oarr lo 0x%x oarr hi 0x%x\n", |
| readl(pcie->base + oarr_offset), |
| readl(pcie->base + oarr_offset + 4)); |
| debug("omap lo 0x%x omap hi 0x%x\n", |
| readl(pcie->base + omap_offset), |
| readl(pcie->base + omap_offset + 4)); |
| |
| return 0; |
| } |
| |
| /** |
| * iproc_pcie_setup_ob() - setup outbound address mapping |
| * |
| * Some iProc SoCs require the SW to configure the outbound address mapping |
| * Outbound address translation: |
| * |
| * iproc_pcie_address = axi_address - axi_offset |
| * OARR = iproc_pcie_address |
| * OMAP = pci_addr |
| * axi_addr -> iproc_pcie_address -> OARR -> OMAP -> pci_address |
| * |
| * @pcie: pcie device |
| * @axi_addr: axi address to be translated |
| * @pci_addr: pci address |
| * @size: window size |
| * |
| * @return: 0 on success and -ve on failure |
| */ |
| static int iproc_pcie_setup_ob(struct iproc_pcie *pcie, u64 axi_addr, |
| u64 pci_addr, resource_size_t size) |
| { |
| struct iproc_pcie_ob *ob = &pcie->ob; |
| int ret = -EINVAL, window_idx, size_idx; |
| |
| if (axi_addr < ob->axi_offset) { |
| pr_err("axi address %pap less than offset %pap\n", |
| &axi_addr, &ob->axi_offset); |
| return -EINVAL; |
| } |
| |
| /* |
| * Translate the AXI address to the internal address used by the iProc |
| * PCIe core before programming the OARR |
| */ |
| axi_addr -= ob->axi_offset; |
| |
| /* iterate through all OARR/OMAP mapping windows */ |
| for (window_idx = ob->nr_windows - 1; window_idx >= 0; window_idx--) { |
| const struct iproc_pcie_ob_map *ob_map = |
| &pcie->ob_map[window_idx]; |
| |
| /* |
| * If current outbound window is already in use, move on to the |
| * next one. |
| */ |
| if (iproc_pcie_ob_is_valid(pcie, window_idx)) |
| continue; |
| |
| /* |
| * Iterate through all supported window sizes within the |
| * OARR/OMAP pair to find a match. Go through the window sizes |
| * in a descending order. |
| */ |
| for (size_idx = ob_map->nr_sizes - 1; size_idx >= 0; |
| size_idx--) { |
| resource_size_t window_size = |
| ob_map->window_sizes[size_idx] * SZ_1M; |
| |
| /* |
| * Keep iterating until we reach the last window and |
| * with the minimal window size at index zero. In this |
| * case, we take a compromise by mapping it using the |
| * minimum window size that can be supported |
| */ |
| if (size < window_size) { |
| if (size_idx > 0 || window_idx > 0) |
| continue; |
| |
| /* |
| * For the corner case of reaching the minimal |
| * window size that can be supported on the |
| * last window |
| */ |
| axi_addr = ALIGN_DOWN(axi_addr, window_size); |
| pci_addr = ALIGN_DOWN(pci_addr, window_size); |
| size = window_size; |
| } |
| |
| if (!IS_ALIGNED(axi_addr, window_size) || |
| !IS_ALIGNED(pci_addr, window_size)) { |
| pr_err("axi %pap or pci %pap not aligned\n", |
| &axi_addr, &pci_addr); |
| return -EINVAL; |
| } |
| |
| /* |
| * Match found! Program both OARR and OMAP and mark |
| * them as a valid entry. |
| */ |
| ret = iproc_pcie_ob_write(pcie, window_idx, size_idx, |
| axi_addr, pci_addr); |
| if (ret) |
| goto err_ob; |
| |
| size -= window_size; |
| if (size == 0) |
| return 0; |
| |
| /* |
| * If we are here, we are done with the current window, |
| * but not yet finished all mappings. Need to move on |
| * to the next window. |
| */ |
| axi_addr += window_size; |
| pci_addr += window_size; |
| break; |
| } |
| } |
| |
| err_ob: |
| pr_err("unable to configure outbound mapping\n"); |
| pr_err("axi %pap, axi offset %pap, pci %pap, res size %pap\n", |
| &axi_addr, &ob->axi_offset, &pci_addr, &size); |
| |
| return ret; |
| } |
| |
| static int iproc_pcie_map_ranges(struct udevice *dev) |
| { |
| struct iproc_pcie *pcie = dev_get_priv(dev); |
| struct udevice *bus = pci_get_controller(dev); |
| struct pci_controller *hose = dev_get_uclass_priv(bus); |
| int i, ret; |
| |
| for (i = 0; i < hose->region_count; i++) { |
| if (hose->regions[i].flags == PCI_REGION_MEM || |
| hose->regions[i].flags == PCI_REGION_PREFETCH) { |
| debug("%d: bus_addr %p, axi_addr %p, size 0x%llx\n", |
| i, &hose->regions[i].bus_start, |
| &hose->regions[i].phys_start, |
| hose->regions[i].size); |
| ret = iproc_pcie_setup_ob(pcie, |
| hose->regions[i].phys_start, |
| hose->regions[i].bus_start, |
| hose->regions[i].size); |
| if (ret) |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static inline bool iproc_pcie_ib_is_in_use(struct iproc_pcie *pcie, |
| int region_idx) |
| { |
| const struct iproc_pcie_ib_map *ib_map = &pcie->ib_map[region_idx]; |
| u32 val; |
| |
| val = iproc_pcie_read_reg(pcie, MAP_REG(IPROC_PCIE_IARR0, region_idx)); |
| |
| return !!(val & (BIT(ib_map->nr_sizes) - 1)); |
| } |
| |
| static inline bool |
| iproc_pcie_ib_check_type(const struct iproc_pcie_ib_map *ib_map, |
| enum iproc_pcie_ib_map_type type) |
| { |
| return !!(ib_map->type == type); |
| } |
| |
| static int iproc_pcie_ib_write(struct iproc_pcie *pcie, int region_idx, |
| int size_idx, int nr_windows, u64 axi_addr, |
| u64 pci_addr, resource_size_t size) |
| { |
| const struct iproc_pcie_ib_map *ib_map = &pcie->ib_map[region_idx]; |
| u16 iarr_offset, imap_offset; |
| u32 val; |
| int window_idx; |
| |
| iarr_offset = iproc_pcie_reg_offset(pcie, MAP_REG(IPROC_PCIE_IARR0, |
| region_idx)); |
| imap_offset = iproc_pcie_reg_offset(pcie, MAP_REG(IPROC_PCIE_IMAP0, |
| region_idx)); |
| if (iproc_pcie_reg_is_invalid(iarr_offset) || |
| iproc_pcie_reg_is_invalid(imap_offset)) |
| return -EINVAL; |
| |
| debug("ib region [%d]: offset 0x%x axi %pap pci %pap\n", |
| region_idx, iarr_offset, &axi_addr, &pci_addr); |
| |
| /* |
| * Program the IARR registers. The upper 32-bit IARR register is |
| * always right after the lower 32-bit IARR register. |
| */ |
| writel(lower_32_bits(pci_addr) | BIT(size_idx), |
| pcie->base + iarr_offset); |
| writel(upper_32_bits(pci_addr), pcie->base + iarr_offset + 4); |
| |
| debug("iarr lo 0x%x iarr hi 0x%x\n", |
| readl(pcie->base + iarr_offset), |
| readl(pcie->base + iarr_offset + 4)); |
| |
| /* |
| * Now program the IMAP registers. Each IARR region may have one or |
| * more IMAP windows. |
| */ |
| size >>= ilog2(nr_windows); |
| for (window_idx = 0; window_idx < nr_windows; window_idx++) { |
| val = readl(pcie->base + imap_offset); |
| val |= lower_32_bits(axi_addr) | IMAP_VALID; |
| writel(val, pcie->base + imap_offset); |
| writel(upper_32_bits(axi_addr), |
| pcie->base + imap_offset + ib_map->imap_addr_offset); |
| |
| debug("imap window [%d] lo 0x%x hi 0x%x\n", |
| window_idx, readl(pcie->base + imap_offset), |
| readl(pcie->base + imap_offset + |
| ib_map->imap_addr_offset)); |
| |
| imap_offset += ib_map->imap_window_offset; |
| axi_addr += size; |
| } |
| |
| return 0; |
| } |
| |
| /** |
| * iproc_pcie_setup_ib() - setup inbound address mapping |
| * |
| * @pcie: pcie device |
| * @axi_addr: axi address to be translated |
| * @pci_addr: pci address |
| * @size: window size |
| * @type: inbound mapping type |
| * |
| * @return: 0 on success and -ve on failure |
| */ |
| static int iproc_pcie_setup_ib(struct iproc_pcie *pcie, u64 axi_addr, |
| u64 pci_addr, resource_size_t size, |
| enum iproc_pcie_ib_map_type type) |
| { |
| struct iproc_pcie_ib *ib = &pcie->ib; |
| int ret; |
| unsigned int region_idx, size_idx; |
| |
| /* iterate through all IARR mapping regions */ |
| for (region_idx = 0; region_idx < ib->nr_regions; region_idx++) { |
| const struct iproc_pcie_ib_map *ib_map = |
| &pcie->ib_map[region_idx]; |
| |
| /* |
| * If current inbound region is already in use or not a |
| * compatible type, move on to the next. |
| */ |
| if (iproc_pcie_ib_is_in_use(pcie, region_idx) || |
| !iproc_pcie_ib_check_type(ib_map, type)) |
| continue; |
| |
| /* iterate through all supported region sizes to find a match */ |
| for (size_idx = 0; size_idx < ib_map->nr_sizes; size_idx++) { |
| resource_size_t region_size = |
| ib_map->region_sizes[size_idx] * ib_map->size_unit; |
| |
| if (size != region_size) |
| continue; |
| |
| if (!IS_ALIGNED(axi_addr, region_size) || |
| !IS_ALIGNED(pci_addr, region_size)) { |
| pr_err("axi %pap or pci %pap not aligned\n", |
| &axi_addr, &pci_addr); |
| return -EINVAL; |
| } |
| |
| /* Match found! Program IARR and all IMAP windows. */ |
| ret = iproc_pcie_ib_write(pcie, region_idx, size_idx, |
| ib_map->nr_windows, axi_addr, |
| pci_addr, size); |
| if (ret) |
| goto err_ib; |
| else |
| return 0; |
| } |
| } |
| ret = -EINVAL; |
| |
| err_ib: |
| pr_err("unable to configure inbound mapping\n"); |
| pr_err("axi %pap, pci %pap, res size %pap\n", |
| &axi_addr, &pci_addr, &size); |
| |
| return ret; |
| } |
| |
| static int iproc_pcie_map_dma_ranges(struct iproc_pcie *pcie) |
| { |
| int ret; |
| struct pci_region regions; |
| int i = 0; |
| |
| while (!pci_get_dma_regions(pcie->dev, ®ions, i)) { |
| dev_dbg(pcie->dev, |
| "dma %d: bus_addr %#llx, axi_addr %#llx, size %#llx\n", |
| i, regions.bus_start, regions.phys_start, regions.size); |
| |
| /* Each range entry corresponds to an inbound mapping region */ |
| ret = iproc_pcie_setup_ib(pcie, regions.phys_start, |
| regions.bus_start, |
| regions.size, |
| IPROC_PCIE_IB_MAP_MEM); |
| if (ret) |
| return ret; |
| i++; |
| } |
| return 0; |
| } |
| |
| static void iproc_pcie_reset_map_regs(struct iproc_pcie *pcie) |
| { |
| struct iproc_pcie_ib *ib = &pcie->ib; |
| struct iproc_pcie_ob *ob = &pcie->ob; |
| int window_idx, region_idx; |
| |
| if (pcie->ep_is_internal) |
| return; |
| |
| /* iterate through all OARR mapping regions */ |
| for (window_idx = ob->nr_windows - 1; window_idx >= 0; window_idx--) { |
| iproc_pcie_write_reg(pcie, MAP_REG(IPROC_PCIE_OARR0, |
| window_idx), 0); |
| } |
| |
| /* iterate through all IARR mapping regions */ |
| for (region_idx = 0; region_idx < ib->nr_regions; region_idx++) { |
| iproc_pcie_write_reg(pcie, MAP_REG(IPROC_PCIE_IARR0, |
| region_idx), 0); |
| } |
| } |
| |
| static void iproc_pcie_reset(struct iproc_pcie *pcie) |
| { |
| u32 val; |
| |
| /* |
| * PAXC and the internal emulated endpoint device downstream should not |
| * be reset. If firmware has been loaded on the endpoint device at an |
| * earlier boot stage, reset here causes issues. |
| */ |
| if (pcie->ep_is_internal) |
| return; |
| |
| /* |
| * Select perst_b signal as reset source. Put the device into reset, |
| * and then bring it out of reset |
| */ |
| val = iproc_pcie_read_reg(pcie, IPROC_PCIE_CLK_CTRL); |
| val &= ~EP_PERST_SOURCE_SELECT & ~EP_MODE_SURVIVE_PERST & |
| ~RC_PCIE_RST_OUTPUT; |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_CLK_CTRL, val); |
| udelay(250); |
| |
| val |= RC_PCIE_RST_OUTPUT; |
| iproc_pcie_write_reg(pcie, IPROC_PCIE_CLK_CTRL, val); |
| mdelay(100); |
| } |
| |
| static inline bool iproc_pcie_link_is_active(struct iproc_pcie *pcie) |
| { |
| u32 val; |
| |
| val = iproc_pcie_read_reg(pcie, IPROC_PCIE_LINK_STATUS); |
| return !!((val & PCIE_PHYLINKUP) && (val & PCIE_DL_ACTIVE)); |
| } |
| |
| static int iproc_pcie_check_link(struct iproc_pcie *pcie) |
| { |
| u32 link_status, class; |
| |
| pcie->link_is_active = false; |
| /* force class to PCI bridge Normal decode (0x060400) */ |
| #define PCI_BRIDGE_CTRL_REG_OFFSET 0x43c |
| #define PCI_BRIDGE_CTRL_REG_CLASS_MASK 0xffffff |
| iproc_pci_raw_config_read32(pcie, 0, |
| PCI_BRIDGE_CTRL_REG_OFFSET, |
| 4, &class); |
| class &= ~PCI_BRIDGE_CTRL_REG_CLASS_MASK; |
| class |= (PCI_CLASS_BRIDGE_PCI << 8); |
| iproc_pci_raw_config_write32(pcie, 0, |
| PCI_BRIDGE_CTRL_REG_OFFSET, |
| 4, class); |
| |
| /* |
| * PAXC connects to emulated endpoint devices directly and does not |
| * have a Serdes. Therefore skip the link detection logic here. |
| */ |
| if (pcie->ep_is_internal) { |
| pcie->link_is_active = true; |
| return 0; |
| } |
| |
| if (!iproc_pcie_link_is_active(pcie)) { |
| pr_err("PHY or data link is INACTIVE!\n"); |
| return -ENODEV; |
| } |
| |
| #define PCI_TARGET_LINK_SPEED_MASK 0xf |
| #define PCI_TARGET_LINK_WIDTH_MASK 0x3f |
| #define PCI_TARGET_LINK_WIDTH_OFFSET 0x4 |
| |
| /* check link status to see if link is active */ |
| iproc_pci_raw_config_read32(pcie, 0, |
| IPROC_PCI_EXP_CAP + PCI_EXP_LNKSTA, |
| 2, &link_status); |
| if (link_status & PCI_EXP_LNKSTA_NLW) |
| pcie->link_is_active = true; |
| |
| if (pcie->link_is_active) |
| pr_info("link UP @ Speed Gen-%d and width-x%d\n", |
| link_status & PCI_TARGET_LINK_SPEED_MASK, |
| (link_status >> PCI_TARGET_LINK_WIDTH_OFFSET) & |
| PCI_TARGET_LINK_WIDTH_MASK); |
| else |
| pr_info("link DOWN\n"); |
| |
| return 0; |
| } |
| |
| static int iproc_pcie_probe(struct udevice *dev) |
| { |
| struct iproc_pcie *pcie = dev_get_priv(dev); |
| int ret; |
| |
| pcie->type = (enum iproc_pcie_type)dev_get_driver_data(dev); |
| debug("PAX type %d\n", pcie->type); |
| pcie->base = dev_read_addr_ptr(dev); |
| debug("PAX reg base %p\n", pcie->base); |
| |
| if (!pcie->base) |
| return -ENODEV; |
| |
| if (dev_read_bool(dev, "brcm,pcie-ob")) |
| pcie->need_ob_cfg = true; |
| |
| pcie->dev = dev; |
| ret = iproc_pcie_rev_init(pcie); |
| if (ret) |
| return ret; |
| |
| if (!pcie->ep_is_internal) { |
| ret = generic_phy_get_by_name(dev, "pcie-phy", &pcie->phy); |
| if (!ret) { |
| ret = generic_phy_init(&pcie->phy); |
| if (ret) { |
| pr_err("failed to init %s PHY\n", dev->name); |
| return ret; |
| } |
| |
| ret = generic_phy_power_on(&pcie->phy); |
| if (ret) { |
| pr_err("power on %s PHY failed\n", dev->name); |
| goto err_exit_phy; |
| } |
| } |
| } |
| |
| iproc_pcie_reset(pcie); |
| |
| if (pcie->need_ob_cfg) { |
| ret = iproc_pcie_map_ranges(dev); |
| if (ret) { |
| pr_err("outbound map failed\n"); |
| goto err_power_off_phy; |
| } |
| } |
| |
| if (pcie->need_ib_cfg) { |
| ret = iproc_pcie_map_dma_ranges(pcie); |
| if (ret) { |
| pr_err("inbound map failed\n"); |
| goto err_power_off_phy; |
| } |
| } |
| |
| if (iproc_pcie_check_link(pcie)) |
| pr_info("no PCIe EP device detected\n"); |
| |
| return 0; |
| |
| err_power_off_phy: |
| generic_phy_power_off(&pcie->phy); |
| err_exit_phy: |
| generic_phy_exit(&pcie->phy); |
| return ret; |
| } |
| |
| static int iproc_pcie_remove(struct udevice *dev) |
| { |
| struct iproc_pcie *pcie = dev_get_priv(dev); |
| int ret; |
| |
| iproc_pcie_reset_map_regs(pcie); |
| |
| if (generic_phy_valid(&pcie->phy)) { |
| ret = generic_phy_power_off(&pcie->phy); |
| if (ret) { |
| pr_err("failed to power off PCIe phy\n"); |
| return ret; |
| } |
| |
| ret = generic_phy_exit(&pcie->phy); |
| if (ret) { |
| pr_err("failed to power off PCIe phy\n"); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static const struct udevice_id pci_iproc_ids[] = { |
| { .compatible = "brcm,iproc-pcie-paxb-v2", |
| .data = IPROC_PCIE_PAXB_V2 }, |
| { .compatible = "brcm,iproc-pcie-paxc-v2", |
| .data = IPROC_PCIE_PAXC_V2 }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(pci_iproc) = { |
| .name = "pci_iproc", |
| .id = UCLASS_PCI, |
| .of_match = pci_iproc_ids, |
| .ops = &iproc_pcie_ops, |
| .probe = iproc_pcie_probe, |
| .remove = iproc_pcie_remove, |
| .priv_auto = sizeof(struct iproc_pcie), |
| .flags = DM_FLAG_OS_PREPARE, |
| }; |