| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright 2017, 2020 NXP |
| */ |
| |
| #ifndef __LS1088A_QDS_H |
| #define __LS1088A_QDS_H |
| |
| #include "ls1088a_common.h" |
| |
| |
| #ifndef __ASSEMBLY__ |
| unsigned long get_board_sys_clk(void); |
| unsigned long get_board_ddr_clk(void); |
| #endif |
| |
| #ifdef CONFIG_TFABOOT |
| #define CONFIG_SYS_MMC_ENV_DEV 0 |
| |
| #define CONFIG_MISC_INIT_R |
| #else |
| #if defined(CONFIG_QSPI_BOOT) |
| #elif defined(CONFIG_SD_BOOT) |
| #define CONFIG_SYS_MMC_ENV_DEV 0 |
| #endif |
| #endif |
| |
| #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_QIXIS_I2C_ACCESS |
| #define SYS_NO_FLASH |
| |
| #undef CONFIG_CMD_IMLS |
| #define CONFIG_SYS_CLK_FREQ 100000000 |
| #define CONFIG_DDR_CLK_FREQ 100000000 |
| #else |
| #define CONFIG_QIXIS_I2C_ACCESS |
| #ifndef CONFIG_DM_I2C |
| #define CONFIG_SYS_I2C_EARLY_INIT |
| #endif |
| #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() |
| #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() |
| #endif |
| |
| #define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ/4) |
| #define COUNTER_FREQUENCY 25000000 /* 25MHz */ |
| |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| |
| #define CONFIG_DDR_SPD |
| #define CONFIG_DDR_ECC |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER |
| #define CONFIG_MEM_INIT_VALUE 0xdeadbeef |
| #define SPD_EEPROM_ADDRESS 0x51 |
| #define CONFIG_SYS_SPD_BUS_NUM 0 |
| |
| |
| /* |
| * IFC Definitions |
| */ |
| #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_SYS_NOR0_CSPR_EXT (0x0) |
| #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) |
| #define CONFIG_SYS_NOR_AMASK_EARLY IFC_AMASK(64*1024*1024) |
| |
| #define CONFIG_SYS_NOR0_CSPR \ |
| (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR0_CSPR_EARLY \ |
| (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR1_CSPR \ |
| (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR1_CSPR_EARLY \ |
| (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH1_BASE_PHYS_EARLY) | \ |
| CSPR_PORT_SIZE_16 | \ |
| CSPR_MSEL_NOR | \ |
| CSPR_V) |
| #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12) |
| #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ |
| FTIM0_NOR_TEADC(0x5) | \ |
| FTIM0_NOR_TAVDS(0x6) | \ |
| FTIM0_NOR_TEAHC(0x5)) |
| #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ |
| FTIM1_NOR_TRAD_NOR(0x1a) | \ |
| FTIM1_NOR_TSEQRAD_NOR(0x13)) |
| #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x8) | \ |
| FTIM2_NOR_TCH(0x8) | \ |
| FTIM2_NOR_TWPH(0xe) | \ |
| FTIM2_NOR_TWP(0x1c)) |
| #define CONFIG_SYS_NOR_FTIM3 0x04000000 |
| #define CONFIG_SYS_IFC_CCR 0x01000000 |
| |
| #ifndef SYS_NO_FLASH |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE,\ |
| CONFIG_SYS_FLASH_BASE + 0x40000000} |
| #endif |
| #endif |
| |
| #define CONFIG_NAND_FSL_IFC |
| #define CONFIG_SYS_NAND_MAX_ECCPOS 256 |
| #define CONFIG_SYS_NAND_MAX_OOBFREE 2 |
| |
| #define CONFIG_SYS_NAND_CSPR_EXT (0x0) |
| #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ |
| | CSPR_MSEL_NAND /* MSEL = NAND */ \ |
| | CSPR_V) |
| #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) |
| |
| #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ |
| | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ |
| | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ |
| | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \ |
| | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ |
| | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ |
| | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ |
| |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| |
| /* ONFI NAND Flash mode0 Timing Params */ |
| #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ |
| FTIM0_NAND_TWP(0x18) | \ |
| FTIM0_NAND_TWCHT(0x07) | \ |
| FTIM0_NAND_TWH(0x0a)) |
| #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ |
| FTIM1_NAND_TWBE(0x39) | \ |
| FTIM1_NAND_TRR(0x0e) | \ |
| FTIM1_NAND_TRP(0x18)) |
| #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ |
| FTIM2_NAND_TREH(0x0a) | \ |
| FTIM2_NAND_TWHRE(0x1e)) |
| #define CONFIG_SYS_NAND_FTIM3 0x0 |
| |
| #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_MTD_NAND_VERIFY_WRITE |
| #define CONFIG_CMD_NAND |
| |
| #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) |
| |
| #define CONFIG_FSL_QIXIS |
| #define CONFIG_SYS_I2C_FPGA_ADDR 0x66 |
| #define QIXIS_LBMAP_SWITCH 6 |
| #define QIXIS_QMAP_MASK 0xe0 |
| #define QIXIS_QMAP_SHIFT 5 |
| #define QIXIS_LBMAP_MASK 0x0f |
| #define QIXIS_LBMAP_SHIFT 0 |
| #define QIXIS_LBMAP_DFLTBANK 0x0e |
| #define QIXIS_LBMAP_ALTBANK 0x2e |
| #define QIXIS_LBMAP_SD 0x00 |
| #define QIXIS_LBMAP_EMMC 0x00 |
| #define QIXIS_LBMAP_IFC 0x00 |
| #define QIXIS_LBMAP_SD_QSPI 0x0e |
| #define QIXIS_LBMAP_QSPI 0x0e |
| #define QIXIS_RCW_SRC_IFC 0x25 |
| #define QIXIS_RCW_SRC_SD 0x40 |
| #define QIXIS_RCW_SRC_EMMC 0x41 |
| #define QIXIS_RCW_SRC_QSPI 0x62 |
| #define QIXIS_RST_CTL_RESET 0x41 |
| #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 |
| #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 |
| #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 |
| #define QIXIS_RST_FORCE_MEM 0x01 |
| #define QIXIS_STAT_PRES1 0xb |
| #define QIXIS_SDID_MASK 0x07 |
| #define QIXIS_ESDHC_NO_ADAPTER 0x7 |
| |
| #define CONFIG_SYS_FPGA_CSPR_EXT (0x0) |
| #define CONFIG_SYS_FPGA_CSPR (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| #define SYS_FPGA_CSPR_FINAL (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ |
| | CSPR_PORT_SIZE_8 \ |
| | CSPR_MSEL_GPCM \ |
| | CSPR_V) |
| |
| #define SYS_FPGA_AMASK IFC_AMASK(64 * 1024) |
| #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(0) |
| #else |
| #define CONFIG_SYS_FPGA_CSOR CSOR_GPCM_ADM_SHIFT(12) |
| #endif |
| /* QIXIS Timing parameters*/ |
| #define SYS_FPGA_CS_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ |
| FTIM0_GPCM_TEADC(0x0e) | \ |
| FTIM0_GPCM_TEAHC(0x0e)) |
| #define SYS_FPGA_CS_FTIM1 (FTIM1_GPCM_TACO(0xff) | \ |
| FTIM1_GPCM_TRAD(0x3f)) |
| #define SYS_FPGA_CS_FTIM2 (FTIM2_GPCM_TCS(0xf) | \ |
| FTIM2_GPCM_TCH(0xf) | \ |
| FTIM2_GPCM_TWP(0x3E)) |
| #define SYS_FPGA_CS_FTIM3 0x0 |
| |
| #ifdef CONFIG_TFABOOT |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY |
| #define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR_EARLY |
| #define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR1_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK_EARLY |
| #define CONFIG_SYS_AMASK1_FINAL CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT |
| #define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR |
| #define CONFIG_SYS_CSPR3_FINAL SYS_FPGA_CSPR_FINAL |
| #define CONFIG_SYS_AMASK3 SYS_FPGA_AMASK |
| #define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR |
| #define CONFIG_SYS_CS3_FTIM0 SYS_FPGA_CS_FTIM0 |
| #define CONFIG_SYS_CS3_FTIM1 SYS_FPGA_CS_FTIM1 |
| #define CONFIG_SYS_CS3_FTIM2 SYS_FPGA_CS_FTIM2 |
| #define CONFIG_SYS_CS3_FTIM3 SYS_FPGA_CS_FTIM3 |
| #else |
| #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_FPGA_CSPR_EXT |
| #define CONFIG_SYS_CSPR2 CONFIG_SYS_FPGA_CSPR |
| #define CONFIG_SYS_CSPR2_FINAL SYS_FPGA_CSPR_FINAL |
| #define CONFIG_SYS_AMASK2 SYS_FPGA_AMASK |
| #define CONFIG_SYS_CSOR2 CONFIG_SYS_FPGA_CSOR |
| #define CONFIG_SYS_CS2_FTIM0 SYS_FPGA_CS_FTIM0 |
| #define CONFIG_SYS_CS2_FTIM1 SYS_FPGA_CS_FTIM1 |
| #define CONFIG_SYS_CS2_FTIM2 SYS_FPGA_CS_FTIM2 |
| #define CONFIG_SYS_CS2_FTIM3 SYS_FPGA_CS_FTIM3 |
| #else |
| #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY |
| #define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR |
| #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT |
| #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR_EARLY |
| #define CONFIG_SYS_CSPR1_FINAL CONFIG_SYS_NOR1_CSPR |
| #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK_EARLY |
| #define CONFIG_SYS_AMASK1_FINAL CONFIG_SYS_NOR_AMASK |
| #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR |
| #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 |
| #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 |
| #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 |
| #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 |
| #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT |
| #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR |
| #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK |
| #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR |
| #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 |
| #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 |
| #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 |
| #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 |
| #define CONFIG_SYS_CSPR3_EXT CONFIG_SYS_FPGA_CSPR_EXT |
| #define CONFIG_SYS_CSPR3 CONFIG_SYS_FPGA_CSPR |
| #define CONFIG_SYS_CSPR3_FINAL SYS_FPGA_CSPR_FINAL |
| #define CONFIG_SYS_AMASK3 SYS_FPGA_AMASK |
| #define CONFIG_SYS_CSOR3 CONFIG_SYS_FPGA_CSOR |
| #define CONFIG_SYS_CS3_FTIM0 SYS_FPGA_CS_FTIM0 |
| #define CONFIG_SYS_CS3_FTIM1 SYS_FPGA_CS_FTIM1 |
| #define CONFIG_SYS_CS3_FTIM2 SYS_FPGA_CS_FTIM2 |
| #define CONFIG_SYS_CS3_FTIM3 SYS_FPGA_CS_FTIM3 |
| #endif |
| #endif |
| |
| #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000 |
| |
| /* |
| * I2C bus multiplexer |
| */ |
| #define I2C_MUX_PCA_ADDR_PRI 0x77 |
| #define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */ |
| #define I2C_RETIMER_ADDR 0x18 |
| #define I2C_RETIMER_ADDR2 0x19 |
| #define I2C_MUX_CH_DEFAULT 0x8 |
| #define I2C_MUX_CH5 0xD |
| |
| #define I2C_MUX_CH_VOL_MONITOR 0xA |
| |
| /* Voltage monitor on channel 2*/ |
| #define I2C_VOL_MONITOR_ADDR 0x63 |
| #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 |
| #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 |
| #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 |
| #define I2C_SVDD_MONITOR_ADDR 0x4F |
| |
| #define CONFIG_VID_FLS_ENV "ls1088aqds_vdd_mv" |
| #define CONFIG_VID |
| |
| /* The lowest and highest voltage allowed for LS1088AQDS */ |
| #define VDD_MV_MIN 819 |
| #define VDD_MV_MAX 1212 |
| |
| #define CONFIG_VOL_MONITOR_LTC3882_SET |
| #define CONFIG_VOL_MONITOR_LTC3882_READ |
| |
| /* PM Bus commands code for LTC3882*/ |
| #define PMBUS_CMD_PAGE 0x0 |
| #define PMBUS_CMD_READ_VOUT 0x8B |
| #define PMBUS_CMD_PAGE_PLUS_WRITE 0x05 |
| #define PMBUS_CMD_VOUT_COMMAND 0x21 |
| |
| #define PWM_CHANNEL0 0x0 |
| |
| /* |
| * RTC configuration |
| */ |
| #define RTC |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/ |
| |
| /* EEPROM */ |
| #define CONFIG_ID_EEPROM |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #define CONFIG_SYS_EEPROM_BUS_NUM 0 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 |
| |
| /* QSPI device */ |
| #if defined(CONFIG_TFABOOT) || \ |
| defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) |
| #define FSL_QSPI_FLASH_SIZE (1 << 26) |
| #define FSL_QSPI_FLASH_NUM 2 |
| |
| #endif |
| |
| #ifdef CONFIG_FSL_DSPI |
| #define CONFIG_SPI_FLASH_STMICRO |
| #define CONFIG_SPI_FLASH_SST |
| #define CONFIG_SPI_FLASH_EON |
| #if !defined(CONFIG_TFABOOT) && \ |
| !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) |
| #endif |
| #endif |
| |
| #define CONFIG_CMD_MEMINFO |
| #define CONFIG_SYS_MEMTEST_START 0x80000000 |
| #define CONFIG_SYS_MEMTEST_END 0x9fffffff |
| |
| #ifdef CONFIG_SPL_BUILD |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE |
| #else |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #endif |
| |
| #define CONFIG_FSL_MEMAC |
| |
| /* MMC */ |
| #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 |
| #define CONFIG_ESDHC_DETECT_QUIRK ((readb(QIXIS_BASE + QIXIS_STAT_PRES1) & \ |
| QIXIS_SDID_MASK) != QIXIS_ESDHC_NO_ADAPTER) |
| |
| /* Initial environment variables */ |
| #ifdef CONFIG_NXP_ESBC |
| #undef CONFIG_EXTRA_ENV_SETTINGS |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "loadaddr=0x90100000\0" \ |
| "kernel_addr=0x100000\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_start=0x1000000\0" \ |
| "kernel_load=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "mcinitcmd=sf probe 0:0;sf read 0xa0a00000 0xa00000 0x100000;" \ |
| "sf read 0xa0640000 0x640000 0x4000; esbc_validate 0xa0640000;" \ |
| "sf read 0xa0e00000 0xe00000 0x100000;" \ |
| "sf read 0xa0680000 0x680000 0x4000;esbc_validate 0xa0680000;" \ |
| "fsl_mc start mc 0xa0a00000 0xa0e00000\0" \ |
| "mcmemsize=0x70000000 \0" |
| #else /* if !(CONFIG_NXP_ESBC) */ |
| #ifdef CONFIG_TFABOOT |
| #define QSPI_MC_INIT_CMD \ |
| "sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \ |
| "sf read 0x80100000 0xE00000 0x100000;" \ |
| "fsl_mc start mc 0x80000000 0x80100000\0" |
| #define SD_MC_INIT_CMD \ |
| "mmcinfo;mmc read 0x80000000 0x5000 0x800;" \ |
| "mmc read 0x80100000 0x7000 0x800;" \ |
| "fsl_mc start mc 0x80000000 0x80100000\0" |
| #define IFC_MC_INIT_CMD \ |
| "fsl_mc start mc 0x580A00000 0x580E00000\0" |
| |
| #undef CONFIG_EXTRA_ENV_SETTINGS |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "loadaddr=0x90100000\0" \ |
| "kernel_addr=0x100000\0" \ |
| "kernel_addr_sd=0x800\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_start=0x1000000\0" \ |
| "kernel_start_sd=0x8000\0" \ |
| "kernel_load=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "kernel_size_sd=0x14000\0" \ |
| "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \ |
| "sf read 0x80100000 0xE00000 0x100000;" \ |
| "fsl_mc start mc 0x80000000 0x80100000\0" \ |
| "mcmemsize=0x70000000 \0" |
| #define QSPI_NOR_BOOTCOMMAND "sf probe 0:0;" \ |
| "sf read 0x80001000 0xd00000 0x100000;"\ |
| " fsl_mc lazyapply dpl 0x80001000 &&" \ |
| " sf read $kernel_load $kernel_start" \ |
| " $kernel_size && bootm $kernel_load" |
| #define SD_BOOTCOMMAND "mmcinfo;mmc read 0x80001000 0x6800 0x800;"\ |
| " fsl_mc lazyapply dpl 0x80001000 &&" \ |
| " mmc read $kernel_load $kernel_start_sd" \ |
| " $kernel_size_sd && bootm $kernel_load" |
| #define IFC_NOR_BOOTCOMMAND "fsl_mc lazyapply dpl 0x580d00000 &&" \ |
| " cp.b $kernel_start $kernel_load" \ |
| " $kernel_size && bootm $kernel_load" |
| #else |
| #if defined(CONFIG_QSPI_BOOT) |
| #undef CONFIG_EXTRA_ENV_SETTINGS |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "loadaddr=0x90100000\0" \ |
| "kernel_addr=0x100000\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_start=0x1000000\0" \ |
| "kernel_load=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "mcinitcmd=sf probe 0:0;sf read 0x80000000 0xA00000 0x100000;" \ |
| "sf read 0x80100000 0xE00000 0x100000;" \ |
| "fsl_mc start mc 0x80000000 0x80100000\0" \ |
| "mcmemsize=0x70000000 \0" |
| #elif defined(CONFIG_SD_BOOT) |
| #undef CONFIG_EXTRA_ENV_SETTINGS |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "loadaddr=0x90100000\0" \ |
| "kernel_addr=0x800\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_start=0x8000\0" \ |
| "kernel_load=0xa0000000\0" \ |
| "kernel_size=0x14000\0" \ |
| "mcinitcmd=mmcinfo;mmc read 0x80000000 0x5000 0x800;" \ |
| "mmc read 0x80100000 0x7000 0x800;" \ |
| "fsl_mc start mc 0x80000000 0x80100000\0" \ |
| "mcmemsize=0x70000000 \0" |
| #else /* NOR BOOT */ |
| #undef CONFIG_EXTRA_ENV_SETTINGS |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "loadaddr=0x90100000\0" \ |
| "kernel_addr=0x100000\0" \ |
| "ramdisk_addr=0x800000\0" \ |
| "ramdisk_size=0x2000000\0" \ |
| "fdt_high=0xa0000000\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "kernel_start=0x1000000\0" \ |
| "kernel_load=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "mcinitcmd=fsl_mc start mc 0x580A00000 0x580E00000\0" \ |
| "mcmemsize=0x70000000 \0" |
| #endif |
| #endif /* CONFIG_TFABOOT */ |
| #endif /* CONFIG_NXP_ESBC */ |
| |
| #ifdef CONFIG_FSL_MC_ENET |
| #define CONFIG_FSL_MEMAC |
| #define CONFIG_PHYLIB |
| #define CONFIG_PHYLIB_10G |
| #define CONFIG_PHY_VITESSE |
| #define CONFIG_PHY_REALTEK |
| #define CONFIG_PHY_TERANETICS |
| #define RGMII_PHY1_ADDR 0x1 |
| #define RGMII_PHY2_ADDR 0x2 |
| #define SGMII_CARD_PORT1_PHY_ADDR 0x1C |
| #define SGMII_CARD_PORT2_PHY_ADDR 0x1d |
| #define SGMII_CARD_PORT3_PHY_ADDR 0x1E |
| #define SGMII_CARD_PORT4_PHY_ADDR 0x1F |
| |
| #define XQSGMII_CARD_PHY1_PORT0_ADDR 0x0 |
| #define XQSGMII_CARD_PHY1_PORT1_ADDR 0x1 |
| #define XQSGMII_CARD_PHY1_PORT2_ADDR 0x2 |
| #define XQSGMII_CARD_PHY1_PORT3_ADDR 0x3 |
| #define XQSGMII_CARD_PHY2_PORT0_ADDR 0x4 |
| #define XQSGMII_CARD_PHY2_PORT1_ADDR 0x5 |
| #define XQSGMII_CARD_PHY2_PORT2_ADDR 0x6 |
| #define XQSGMII_CARD_PHY2_PORT3_ADDR 0x7 |
| #define XQSGMII_CARD_PHY3_PORT0_ADDR 0x8 |
| #define XQSGMII_CARD_PHY3_PORT1_ADDR 0x9 |
| #define XQSGMII_CARD_PHY3_PORT2_ADDR 0xa |
| #define XQSGMII_CARD_PHY3_PORT3_ADDR 0xb |
| #define XQSGMII_CARD_PHY4_PORT0_ADDR 0xc |
| #define XQSGMII_CARD_PHY4_PORT1_ADDR 0xd |
| #define XQSGMII_CARD_PHY4_PORT2_ADDR 0xe |
| #define XQSGMII_CARD_PHY4_PORT3_ADDR 0xf |
| |
| #define CONFIG_ETHPRIME "DPMAC1@xgmii" |
| #define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ |
| |
| #endif |
| |
| #define BOOT_TARGET_DEVICES(func) \ |
| func(USB, usb, 0) \ |
| func(MMC, mmc, 0) \ |
| func(SCSI, scsi, 0) \ |
| func(DHCP, dhcp, na) |
| #include <config_distro_bootcmd.h> |
| |
| #include <asm/fsl_secure_boot.h> |
| |
| #endif /* __LS1088A_QDS_H */ |