| /* |
| * Copyright (C) 2015 Freescale Semiconductor, Inc. |
| * |
| * Configuration settings for the Freescale i.MX7D SABRESD board. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __MX7D_SABRESD_CONFIG_H |
| #define __MX7D_SABRESD_CONFIG_H |
| |
| #include "mx7_common.h" |
| |
| #define CONFIG_DBG_MONITOR |
| #define PHYS_SDRAM_SIZE SZ_1G |
| |
| #define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR |
| |
| /* Size of malloc() pool */ |
| #define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M) |
| |
| #define CONFIG_BOARD_EARLY_INIT_F |
| #define CONFIG_BOARD_LATE_INIT |
| |
| /* Uncomment to enable secure boot support */ |
| /* #define CONFIG_SECURE_BOOT */ |
| #define CONFIG_CSF_SIZE 0x4000 |
| |
| /* Network */ |
| #define CONFIG_CMD_MII |
| #define CONFIG_FEC_MXC |
| #define CONFIG_MII |
| #define CONFIG_FEC_XCV_TYPE RGMII |
| #define CONFIG_ETHPRIME "FEC" |
| #define CONFIG_FEC_MXC_PHYADDR 0 |
| |
| #define CONFIG_PHYLIB |
| #define CONFIG_PHY_BROADCOM |
| /* ENET1 */ |
| #define IMX_FEC_BASE ENET_IPS_BASE_ADDR |
| |
| /* MMC Config*/ |
| #define CONFIG_SYS_FSL_ESDHC_ADDR 0 |
| |
| /* PMIC */ |
| #define CONFIG_POWER |
| #define CONFIG_POWER_I2C |
| #define CONFIG_POWER_PFUZE3000 |
| #define CONFIG_POWER_PFUZE3000_I2C_ADDR 0x08 |
| |
| #undef CONFIG_BOOTM_NETBSD |
| #undef CONFIG_BOOTM_PLAN9 |
| #undef CONFIG_BOOTM_RTEMS |
| |
| #undef CONFIG_CMD_EXPORTENV |
| #undef CONFIG_CMD_IMPORTENV |
| |
| /* I2C configs */ |
| #define CONFIG_CMD_I2C |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_MXC |
| #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ |
| #define CONFIG_SYS_I2C_SPEED 100000 |
| |
| #define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */ |
| #define CONFIG_SYS_MMC_IMG_LOAD_PART 1 |
| |
| #ifdef CONFIG_IMX_BOOTAUX |
| /* Set to QSPI1 A flash at default */ |
| #define CONFIG_SYS_AUXCORE_BOOTDATA 0x60000000 |
| #define CONFIG_CMD_SETEXPR |
| |
| #define UPDATE_M4_ENV \ |
| "m4image=m4_qspi.bin\0" \ |
| "loadm4image=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4image}\0" \ |
| "update_m4_from_sd=" \ |
| "if sf probe 0:0; then " \ |
| "if run loadm4image; then " \ |
| "setexpr fw_sz ${filesize} + 0xffff; " \ |
| "setexpr fw_sz ${fw_sz} / 0x10000; " \ |
| "setexpr fw_sz ${fw_sz} * 0x10000; " \ |
| "sf erase 0x0 ${fw_sz}; " \ |
| "sf write ${loadaddr} 0x0 ${filesize}; " \ |
| "fi; " \ |
| "fi\0" \ |
| "m4boot=sf probe 0:0; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0" |
| #else |
| #define UPDATE_M4_ENV "" |
| #endif |
| |
| #define CONFIG_MFG_ENV_SETTINGS \ |
| "mfgtool_args=setenv bootargs console=${console},${baudrate} " \ |
| "rdinit=/linuxrc " \ |
| "g_mass_storage.stall=0 g_mass_storage.removable=1 " \ |
| "g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\ |
| "g_mass_storage.iSerialNumber=\"\" "\ |
| "clk_ignore_unused "\ |
| "\0" \ |
| "initrd_addr=0x83800000\0" \ |
| "initrd_high=0xffffffff\0" \ |
| "bootcmd_mfg=run mfgtool_args;bootz ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \ |
| |
| #define CONFIG_DFU_ENV_SETTINGS \ |
| "dfu_alt_info=image raw 0 0x800000;"\ |
| "u-boot raw 0 0x4000;"\ |
| "bootimg part 0 1;"\ |
| "rootfs part 0 2\0" \ |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| UPDATE_M4_ENV \ |
| CONFIG_MFG_ENV_SETTINGS \ |
| CONFIG_DFU_ENV_SETTINGS \ |
| "script=boot.scr\0" \ |
| "image=zImage\0" \ |
| "console=ttymxc0\0" \ |
| "fdt_high=0xffffffff\0" \ |
| "initrd_high=0xffffffff\0" \ |
| "fdt_file=imx7d-sdb.dtb\0" \ |
| "fdt_addr=0x83000000\0" \ |
| "boot_fdt=try\0" \ |
| "ip_dyn=yes\0" \ |
| "videomode=video=ctfb:x:480,y:272,depth:24,pclk:108695,le:8,ri:4,up:2,lo:4,hs:41,vs:10,sync:0,vmode:0\0" \ |
| "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \ |
| "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \ |
| "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \ |
| "mmcautodetect=yes\0" \ |
| "mmcargs=setenv bootargs console=${console},${baudrate} " \ |
| "root=${mmcroot}\0" \ |
| "loadbootscript=" \ |
| "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ |
| "bootscript=echo Running bootscript from mmc ...; " \ |
| "source\0" \ |
| "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ |
| "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ |
| "mmcboot=echo Booting from mmc ...; " \ |
| "run mmcargs; " \ |
| "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ |
| "if run loadfdt; then " \ |
| "bootz ${loadaddr} - ${fdt_addr}; " \ |
| "else " \ |
| "if test ${boot_fdt} = try; then " \ |
| "bootz; " \ |
| "else " \ |
| "echo WARN: Cannot load the DT; " \ |
| "fi; " \ |
| "fi; " \ |
| "else " \ |
| "bootz; " \ |
| "fi;\0" \ |
| "netargs=setenv bootargs console=${console},${baudrate} " \ |
| "root=/dev/nfs " \ |
| "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ |
| "netboot=echo Booting from net ...; " \ |
| "run netargs; " \ |
| "if test ${ip_dyn} = yes; then " \ |
| "setenv get_cmd dhcp; " \ |
| "else " \ |
| "setenv get_cmd tftp; " \ |
| "fi; " \ |
| "${get_cmd} ${image}; " \ |
| "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ |
| "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ |
| "bootz ${loadaddr} - ${fdt_addr}; " \ |
| "else " \ |
| "if test ${boot_fdt} = try; then " \ |
| "bootz; " \ |
| "else " \ |
| "echo WARN: Cannot load the DT; " \ |
| "fi; " \ |
| "fi; " \ |
| "else " \ |
| "bootz; " \ |
| "fi;\0" |
| |
| #define CONFIG_BOOTCOMMAND \ |
| "mmc dev ${mmcdev};" \ |
| "mmc dev ${mmcdev}; if mmc rescan; then " \ |
| "if run loadbootscript; then " \ |
| "run bootscript; " \ |
| "else " \ |
| "if run loadimage; then " \ |
| "run mmcboot; " \ |
| "else run netboot; " \ |
| "fi; " \ |
| "fi; " \ |
| "else run netboot; fi" |
| |
| #define CONFIG_CMD_MEMTEST |
| #define CONFIG_SYS_MEMTEST_START 0x80000000 |
| #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 0x20000000) |
| |
| #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR |
| #define CONFIG_SYS_HZ 1000 |
| |
| #define CONFIG_STACKSIZE SZ_128K |
| |
| /* Physical Memory Map */ |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define PHYS_SDRAM MMDC0_ARB_BASE_ADDR |
| |
| #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM |
| #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR |
| #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE |
| |
| #define CONFIG_SYS_INIT_SP_OFFSET \ |
| (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_ADDR \ |
| (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) |
| |
| /* FLASH and environment organization */ |
| #define CONFIG_SYS_NO_FLASH |
| #define CONFIG_ENV_SIZE SZ_8K |
| #define CONFIG_ENV_IS_IN_MMC |
| |
| /* |
| * If want to use nand, define CONFIG_NAND_MXS and rework board |
| * to support nand, since emmc has pin conflicts with nand |
| */ |
| #ifdef CONFIG_NAND_MXS |
| #define CONFIG_CMD_NAND |
| #define CONFIG_CMD_NAND_TRIMFFS |
| |
| /* NAND stuff */ |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE 0x40000000 |
| #define CONFIG_SYS_NAND_5_ADDR_CYCLE |
| #define CONFIG_SYS_NAND_ONFI_DETECTION |
| |
| /* DMA stuff, needed for GPMI/MXS NAND support */ |
| #define CONFIG_APBH_DMA |
| #define CONFIG_APBH_DMA_BURST |
| #define CONFIG_APBH_DMA_BURST8 |
| #endif |
| |
| #define CONFIG_ENV_OFFSET (8 * SZ_64K) |
| #ifdef CONFIG_NAND_MXS |
| #define CONFIG_SYS_FSL_USDHC_NUM 1 |
| #else |
| #define CONFIG_SYS_FSL_USDHC_NUM 2 |
| #endif |
| |
| #define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC1 */ |
| #define CONFIG_SYS_MMC_ENV_PART 0 /* user area */ |
| #define CONFIG_MMCROOT "/dev/mmcblk0p2" /* USDHC1 */ |
| |
| /* USB Configs */ |
| #define CONFIG_CMD_USB |
| #define CONFIG_USB_EHCI |
| #define CONFIG_USB_EHCI_MX7 |
| #define CONFIG_USB_STORAGE |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| #define CONFIG_USB_HOST_ETHER |
| #define CONFIG_USB_ETHER_ASIX |
| #define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) |
| #define CONFIG_MXC_USB_FLAGS 0 |
| #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 |
| |
| #define CONFIG_IMX_THERMAL |
| |
| #define CONFIG_USBD_HS |
| |
| #define CONFIG_CMD_USB_MASS_STORAGE |
| #define CONFIG_USB_FUNCTION_MASS_STORAGE |
| #define CONFIG_USB_GADGET_DOWNLOAD |
| |
| #define CONFIG_G_DNL_VENDOR_NUM 0x0525 |
| #define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5 |
| #define CONFIG_G_DNL_MANUFACTURER "FSL" |
| |
| /* USB Device Firmware Update support */ |
| #define CONFIG_CMD_DFU |
| #define CONFIG_USB_FUNCTION_DFU |
| #define CONFIG_DFU_MMC |
| #define CONFIG_DFU_RAM |
| |
| #define CONFIG_VIDEO |
| #ifdef CONFIG_VIDEO |
| #define CONFIG_CFB_CONSOLE |
| #define CONFIG_VIDEO_MXS |
| #define CONFIG_VIDEO_LOGO |
| #define CONFIG_VIDEO_SW_CURSOR |
| #define CONFIG_VGA_AS_SINGLE_DEVICE |
| #define CONFIG_SYS_CONSOLE_IS_IN_ENV |
| #define CONFIG_SPLASH_SCREEN |
| #define CONFIG_SPLASH_SCREEN_ALIGN |
| #define CONFIG_CMD_BMP |
| #define CONFIG_BMP_16BPP |
| #define CONFIG_VIDEO_BMP_RLE8 |
| #define CONFIG_VIDEO_BMP_LOGO |
| #endif |
| |
| #ifdef CONFIG_FSL_QSPI |
| #define CONFIG_CMD_SF |
| #define CONFIG_SPI_FLASH |
| #define CONFIG_SPI_FLASH_MACRONIX |
| #define CONFIG_SPI_FLASH_BAR |
| #define CONFIG_SF_DEFAULT_BUS 0 |
| #define CONFIG_SF_DEFAULT_CS 0 |
| #define CONFIG_SF_DEFAULT_SPEED 40000000 |
| #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 |
| #define FSL_QSPI_FLASH_NUM 1 |
| #define FSL_QSPI_FLASH_SIZE SZ_64M |
| #define QSPI0_BASE_ADDR QSPI1_IPS_BASE_ADDR |
| #define QSPI0_AMBA_BASE QSPI0_ARB_BASE_ADDR |
| #endif |
| |
| #endif /* __CONFIG_H */ |