| // SPDX-License-Identifier: GPL-2.0+ OR X11 |
| /* |
| * (C) Copyright 2017 Theobroma Systems Design und Consulting GmbH |
| */ |
| |
| /dts-v1/; |
| #include "rk3368.dtsi" |
| #include "rk3368-lion-u-boot.dtsi" |
| #include <dt-bindings/input/input.h> |
| |
| / { |
| model = "Theobroma Systems RK3368-uQ7 SoM"; |
| compatible = "tsd,rk3368-uq7", "tsd,lion", "rockchip,rk3368"; |
| |
| aliases { |
| mmc0 = &emmc; |
| mmc1 = &sdmmc; |
| }; |
| |
| memory@0 { |
| device_type = "memory"; |
| reg = <0x0 0x0 0x0 0x80000000>; |
| }; |
| |
| ext_gmac: gmac-clk { |
| compatible = "fixed-clock"; |
| clock-frequency = <125000000>; |
| clock-output-names = "ext_gmac"; |
| #clock-cells = <0>; |
| }; |
| |
| vcc_sys: vcc-sys-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vcc_sys"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| }; |
| |
| &uart0 { |
| status = "okay"; |
| }; |
| |
| &emmc { |
| status = "okay"; |
| bus-width = <8>; |
| cap-mmc-highspeed; |
| clock-frequency = <150000000>; |
| disable-wp; |
| keep-power-in-suspend; |
| non-removable; |
| num-slots = <1>; |
| vmmc-supply = <&vcc33_io>; |
| vqmmc-supply = <&vcc18_io>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_bus8>; |
| }; |
| |
| &sdmmc { |
| status = "okay"; |
| }; |
| |
| &gmac { |
| status = "okay"; |
| phy-supply = <&vcc33_io>; |
| phy-mode = "rgmii"; |
| clock_in_out = "input"; |
| snps,reset-gpio = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>; |
| snps,reset-active-low; |
| snps,reset-delays-us = <2 10000 50000>; |
| assigned-clocks = <&cru SCLK_MAC>; |
| assigned-clock-parents = <&ext_gmac>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&rgmii_pins>; |
| tx_delay = <0x10>; |
| rx_delay = <0x10>; |
| }; |
| |
| &i2c0 { |
| status = "okay"; |
| |
| rk808: pmic@1b { |
| compatible = "rockchip,rk808"; |
| reg = <0x1b>; |
| interrupt-parent = <&gpio0>; |
| interrupts = <5 IRQ_TYPE_LEVEL_LOW>; |
| rockchip,system-power-controller; |
| vcc1-supply = <&vcc_sys>; |
| vcc2-supply = <&vcc_sys>; |
| vcc3-supply = <&vcc_sys>; |
| vcc4-supply = <&vcc_sys>; |
| vcc6-supply = <&vcc_sys>; |
| vcc7-supply = <&vcc_sys>; |
| vcc8-supply = <&vcc_sys>; |
| vcc9-supply = <&vcc_sys>; |
| vcc10-supply = <&vcc_sys>; |
| vcc11-supply = <&vcc_sys>; |
| vcc12-supply = <&vcc_sys>; |
| clock-output-names = "xin32k", "rk808-clkout2"; |
| #clock-cells = <1>; |
| |
| regulators { |
| vdd_cpu: DCDC_REG1 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1500000>; |
| regulator-name = "vdd_cpu"; |
| }; |
| |
| vdd_log: DCDC_REG2 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1500000>; |
| regulator-name = "vdd_log"; |
| }; |
| |
| vcc_ddr: DCDC_REG3 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-name = "vcc_ddr"; |
| }; |
| |
| vcc33_io: DCDC_REG4 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "vcc33_io"; |
| }; |
| |
| vcc33_video: LDO_REG2 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-name = "vcc33_video"; |
| }; |
| |
| vdd10_pll: LDO_REG3 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-name = "vdd10_pll"; |
| }; |
| |
| vcc18_io: LDO_REG4 { |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "vcc18_io"; |
| }; |
| |
| vdd10_video: LDO_REG6 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <1000000>; |
| regulator-name = "vdd10_video"; |
| }; |
| |
| vcc18_video: LDO_REG8 { |
| regulator-always-on; |
| regulator-boot-on; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-name = "vcc18_video"; |
| }; |
| }; |
| }; |
| }; |
| |
| &uart0 { |
| status = "okay"; |
| }; |
| |
| &spi1 { |
| status = "okay"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| spiflash: w25q32dw@0 { |
| compatible = "jedec,spi-nor"; |
| reg = <0>; |
| spi-max-frequency = <49500000>; |
| spi-cpol; |
| spi-cpha; |
| }; |
| }; |