| /* |
| * Copyright 2014 Freescale Semiconductor, Inc. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <common.h> |
| #include <command.h> |
| #include <i2c.h> |
| #include <netdev.h> |
| #include <linux/compiler.h> |
| #include <asm/mmu.h> |
| #include <asm/processor.h> |
| #include <asm/cache.h> |
| #include <asm/immap_85xx.h> |
| #include <asm/fsl_law.h> |
| #include <asm/fsl_serdes.h> |
| #include <asm/fsl_portals.h> |
| #include <asm/fsl_liodn.h> |
| #include <fm_eth.h> |
| #include <hwconfig.h> |
| #include <asm/mpc85xx_gpio.h> |
| #include "../common/qixis.h" |
| #include "t102xqds.h" |
| #include "t102xqds_qixis.h" |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| int checkboard(void) |
| { |
| char buf[64]; |
| struct cpu_type *cpu = gd->arch.cpu; |
| static const char *const freq[] = {"100", "125", "156.25", "100.0"}; |
| int clock; |
| u8 sw = QIXIS_READ(arch); |
| |
| printf("Board: %sQDS, ", cpu->name); |
| printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4); |
| printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1); |
| |
| #ifdef CONFIG_SDCARD |
| puts("SD/MMC\n"); |
| #elif CONFIG_SPIFLASH |
| puts("SPI\n"); |
| #else |
| sw = QIXIS_READ(brdcfg[0]); |
| sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT; |
| |
| if (sw < 0x8) |
| printf("vBank: %d\n", sw); |
| else if (sw == 0x8) |
| puts("PromJet\n"); |
| else if (sw == 0x9) |
| puts("NAND\n"); |
| else if (sw == 0x15) |
| printf("IFC Card\n"); |
| else |
| printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH); |
| #endif |
| |
| printf("FPGA: v%d (%s), build %d", |
| (int)QIXIS_READ(scver), qixis_read_tag(buf), |
| (int)qixis_read_minor()); |
| /* the timestamp string contains "\n" at the end */ |
| printf(" on %s", qixis_read_time(buf)); |
| |
| puts("SERDES Reference: "); |
| sw = QIXIS_READ(brdcfg[2]); |
| clock = (sw >> 6) & 3; |
| printf("Clock1=%sMHz ", freq[clock]); |
| clock = (sw >> 4) & 3; |
| printf("Clock2=%sMHz\n", freq[clock]); |
| |
| return 0; |
| } |
| |
| int select_i2c_ch_pca9547(u8 ch) |
| { |
| int ret; |
| |
| ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1); |
| if (ret) { |
| puts("PCA: failed to select proper channel\n"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int board_mux_lane_to_slot(void) |
| { |
| ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR); |
| u32 srds_prtcl_s1; |
| u8 brdcfg9; |
| |
| srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) & |
| FSL_CORENET2_RCWSR4_SRDS1_PRTCL; |
| srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT; |
| |
| |
| brdcfg9 = QIXIS_READ(brdcfg[9]); |
| QIXIS_WRITE(brdcfg[9], brdcfg9 | BRDCFG9_XFI_TX_DISABLE); |
| |
| switch (srds_prtcl_s1) { |
| case 0: |
| /* SerDes1 is not enabled */ |
| break; |
| case 0xd5: |
| case 0x5b: |
| case 0x6b: |
| case 0x77: |
| case 0x6f: |
| case 0x7f: |
| QIXIS_WRITE(brdcfg[12], 0x8c); |
| break; |
| case 0x40: |
| QIXIS_WRITE(brdcfg[12], 0xfc); |
| break; |
| case 0xd6: |
| case 0x5a: |
| case 0x6a: |
| case 0x56: |
| QIXIS_WRITE(brdcfg[12], 0x88); |
| break; |
| case 0x47: |
| QIXIS_WRITE(brdcfg[12], 0xcc); |
| break; |
| case 0x46: |
| QIXIS_WRITE(brdcfg[12], 0xc8); |
| break; |
| case 0x95: |
| case 0x99: |
| brdcfg9 &= ~BRDCFG9_XFI_TX_DISABLE; |
| QIXIS_WRITE(brdcfg[9], brdcfg9); |
| QIXIS_WRITE(brdcfg[12], 0x8c); |
| break; |
| case 0x116: |
| QIXIS_WRITE(brdcfg[12], 0x00); |
| break; |
| case 0x115: |
| case 0x119: |
| case 0x129: |
| case 0x12b: |
| /* Aurora, PCIe, SGMII, SATA */ |
| QIXIS_WRITE(brdcfg[12], 0x04); |
| break; |
| default: |
| printf("WARNING: unsupported for SerDes Protocol %d\n", |
| srds_prtcl_s1); |
| return -1; |
| } |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PPC_T1024 |
| static void board_mux_setup(void) |
| { |
| u8 brdcfg15; |
| |
| brdcfg15 = QIXIS_READ(brdcfg[15]); |
| brdcfg15 &= ~BRDCFG15_DIUSEL_MASK; |
| |
| if (hwconfig_arg_cmp("pin_mux", "tdm")) { |
| /* Route QE_TDM multiplexed signals to TDM Riser slot */ |
| QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_TDM); |
| QIXIS_WRITE(brdcfg[13], BRDCFG13_TDM_INTERFACE << 2); |
| QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) & |
| ~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_TDM); |
| } else if (hwconfig_arg_cmp("pin_mux", "ucc")) { |
| /* to UCC (ProfiBus) interface */ |
| QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_UCC); |
| } else if (hwconfig_arg_cmp("pin_mux", "hdmi")) { |
| /* to DVI (HDMI) encoder */ |
| QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_HDMI); |
| } else if (hwconfig_arg_cmp("pin_mux", "lcd")) { |
| /* to DFP (LCD) encoder */ |
| QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_LCDFM | |
| BRDCFG15_LCDPD | BRDCFG15_DIUSEL_LCD); |
| } |
| |
| if (hwconfig_arg_cmp("adaptor", "sdxc")) |
| /* Route SPI_CS multiplexed signals to SD slot */ |
| QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) & |
| ~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_SDHC); |
| } |
| #endif |
| |
| int board_early_init_r(void) |
| { |
| #ifdef CONFIG_SYS_FLASH_BASE |
| const unsigned int flashbase = CONFIG_SYS_FLASH_BASE; |
| int flash_esel = find_tlb_idx((void *)flashbase, 1); |
| |
| /* |
| * Remap Boot flash + PROMJET region to caching-inhibited |
| * so that flash can be erased properly. |
| */ |
| |
| /* Flush d-cache and invalidate i-cache of any FLASH data */ |
| flush_dcache(); |
| invalidate_icache(); |
| |
| if (flash_esel == -1) { |
| /* very unlikely unless something is messed up */ |
| puts("Error: Could not find TLB for FLASH BASE\n"); |
| flash_esel = 2; /* give our best effort to continue */ |
| } else { |
| /* invalidate existing TLB entry for flash + promjet */ |
| disable_tlb(flash_esel); |
| } |
| |
| set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS, |
| MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G, |
| 0, flash_esel, BOOKE_PAGESZ_256M, 1); |
| #endif |
| set_liodns(); |
| #ifdef CONFIG_SYS_DPAA_QBMAN |
| setup_portals(); |
| #endif |
| select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT); |
| board_mux_lane_to_slot(); |
| return 0; |
| } |
| |
| unsigned long get_board_sys_clk(void) |
| { |
| u8 sysclk_conf = QIXIS_READ(brdcfg[1]); |
| |
| switch (sysclk_conf & 0x0F) { |
| case QIXIS_SYSCLK_64: |
| return 64000000; |
| case QIXIS_SYSCLK_83: |
| return 83333333; |
| case QIXIS_SYSCLK_100: |
| return 100000000; |
| case QIXIS_SYSCLK_125: |
| return 125000000; |
| case QIXIS_SYSCLK_133: |
| return 133333333; |
| case QIXIS_SYSCLK_150: |
| return 150000000; |
| case QIXIS_SYSCLK_160: |
| return 160000000; |
| case QIXIS_SYSCLK_166: |
| return 166666666; |
| } |
| return 66666666; |
| } |
| |
| unsigned long get_board_ddr_clk(void) |
| { |
| u8 ddrclk_conf = QIXIS_READ(brdcfg[1]); |
| |
| switch ((ddrclk_conf & 0x30) >> 4) { |
| case QIXIS_DDRCLK_100: |
| return 100000000; |
| case QIXIS_DDRCLK_125: |
| return 125000000; |
| case QIXIS_DDRCLK_133: |
| return 133333333; |
| } |
| return 66666666; |
| } |
| |
| #define NUM_SRDS_PLL 2 |
| int misc_init_r(void) |
| { |
| #ifdef CONFIG_PPC_T1024 |
| board_mux_setup(); |
| #endif |
| return 0; |
| } |
| |
| void fdt_fixup_spi_mux(void *blob) |
| { |
| int nodeoff = 0; |
| |
| if (hwconfig_arg_cmp("pin_mux", "tdm")) { |
| while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, |
| "eon,en25s64")) >= 0) { |
| fdt_del_node(blob, nodeoff); |
| } |
| } else { |
| /* remove tdm node */ |
| while ((nodeoff = fdt_node_offset_by_compatible(blob, 0, |
| "maxim,ds26522")) >= 0) { |
| fdt_del_node(blob, nodeoff); |
| } |
| } |
| } |
| |
| int ft_board_setup(void *blob, bd_t *bd) |
| { |
| phys_addr_t base; |
| phys_size_t size; |
| |
| ft_cpu_setup(blob, bd); |
| |
| base = getenv_bootm_low(); |
| size = getenv_bootm_size(); |
| |
| fdt_fixup_memory(blob, (u64)base, (u64)size); |
| |
| #ifdef CONFIG_PCI |
| pci_of_setup(blob, bd); |
| #endif |
| |
| fdt_fixup_liodn(blob); |
| |
| #ifdef CONFIG_HAS_FSL_DR_USB |
| fdt_fixup_dr_usb(blob, bd); |
| #endif |
| |
| #ifdef CONFIG_SYS_DPAA_FMAN |
| fdt_fixup_fman_ethernet(blob); |
| fdt_fixup_board_enet(blob); |
| #endif |
| fdt_fixup_spi_mux(blob); |
| |
| return 0; |
| } |
| |
| void qixis_dump_switch(void) |
| { |
| int i, nr_of_cfgsw; |
| |
| QIXIS_WRITE(cms[0], 0x00); |
| nr_of_cfgsw = QIXIS_READ(cms[1]); |
| |
| puts("DIP switch settings dump:\n"); |
| for (i = 1; i <= nr_of_cfgsw; i++) { |
| QIXIS_WRITE(cms[0], i); |
| printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1])); |
| } |
| } |
| |
| #ifdef CONFIG_DEEP_SLEEP |
| void board_mem_sleep_setup(void) |
| { |
| /* does not provide HW signals for power management */ |
| QIXIS_WRITE(pwr_ctl[1], (QIXIS_READ(pwr_ctl[1]) & ~0x2)); |
| /* Disable MCKE isolation */ |
| gpio_set_value(2, 0); |
| udelay(1); |
| } |
| #endif |