blob: 2452e63881f15d1145842e9960a7a23d69d2d010 [file] [log] [blame]
/*
* Copyright (C) 2012 Atmel Corporation
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/at91sam9x5_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
#include <debug_uart.h>
#include <lcd.h>
#include <atmel_hlcdc.h>
#ifdef CONFIG_LCD_INFO
#include <nand.h>
#include <version.h>
#endif
#include <asm/mach-types.h>
DECLARE_GLOBAL_DATA_PTR;
/* ------------------------------------------------------------------------- */
/*
* Miscelaneous platform dependent initialisations
*/
#ifdef CONFIG_CMD_NAND
static void at91sam9x5ek_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
unsigned long csa;
/* Enable CS3 */
csa = readl(&matrix->ebicsa);
csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
/* NAND flash on D16 */
csa |= AT91_MATRIX_NFD0_ON_D16;
/* Configure IO drive */
csa &= ~AT91_MATRIX_EBI_EBI_IOSR_NORMAL;
writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) |
AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(6),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(6),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_MODE_DBW_8 |
#endif
AT91_SMC_MODE_TDF_CYCLE(1),
&smc->cs[3].mode);
at91_periph_clk_enable(ATMEL_ID_PIOCD);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
at91_pio3_set_a_periph(AT91_PIO_PORTD, 0, 1); /* NAND OE */
at91_pio3_set_a_periph(AT91_PIO_PORTD, 1, 1); /* NAND WE */
at91_pio3_set_a_periph(AT91_PIO_PORTD, 2, 1); /* NAND ALE */
at91_pio3_set_a_periph(AT91_PIO_PORTD, 3, 1); /* NAND CLE */
at91_pio3_set_a_periph(AT91_PIO_PORTD, 6, 1);
at91_pio3_set_a_periph(AT91_PIO_PORTD, 7, 1);
at91_pio3_set_a_periph(AT91_PIO_PORTD, 8, 1);
at91_pio3_set_a_periph(AT91_PIO_PORTD, 9, 1);
at91_pio3_set_a_periph(AT91_PIO_PORTD, 10, 1);
at91_pio3_set_a_periph(AT91_PIO_PORTD, 11, 1);
at91_pio3_set_a_periph(AT91_PIO_PORTD, 12, 1);
at91_pio3_set_a_periph(AT91_PIO_PORTD, 13, 1);
}
#endif
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
.vl_col = 800,
.vl_row = 480,
.vl_clk = 24000000,
.vl_sync = LCDC_LCDCFG5_HSPOL | LCDC_LCDCFG5_VSPOL,
.vl_bpix = LCD_BPP,
.vl_tft = 1,
.vl_clk_pol = 1,
.vl_hsync_len = 128,
.vl_left_margin = 64,
.vl_right_margin = 64,
.vl_vsync_len = 2,
.vl_upper_margin = 22,
.vl_lower_margin = 21,
.mmio = ATMEL_BASE_LCDC,
};
void lcd_enable(void)
{
if (has_lcdc())
at91_pio3_set_a_periph(AT91_PIO_PORTC, 29, 1); /* power up */
}
void lcd_disable(void)
{
if (has_lcdc())
at91_pio3_set_a_periph(AT91_PIO_PORTC, 29, 0); /* power down */
}
static void at91sam9x5ek_lcd_hw_init(void)
{
if (has_lcdc()) {
at91_pio3_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDPWM */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDVSYNC */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 28, 0); /* LCDHSYNC */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDDISP */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 29, 0); /* LCDDEN */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 30, 0); /* LCDPCK */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 0, 0); /* LCDD0 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDD1 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDD2 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDD3 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 4, 0); /* LCDD4 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 5, 0); /* LCDD5 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 6, 0); /* LCDD6 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 7, 0); /* LCDD7 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 8, 0); /* LCDD8 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 9, 0); /* LCDD9 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDD10 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDD11 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 12, 0); /* LCDD12 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 13, 0); /* LCDD13 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDD14 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDD15 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDD16 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 17, 0); /* LCDD17 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDD18 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDD19 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 20, 0); /* LCDD20 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 21, 0); /* LCDD21 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD22 */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD23 */
at91_periph_clk_enable(ATMEL_ID_LCDC);
}
}
#ifdef CONFIG_LCD_INFO
void lcd_show_board_info(void)
{
ulong dram_size, nand_size;
int i;
char temp[32];
if (has_lcdc()) {
lcd_printf("%s\n", U_BOOT_VERSION);
lcd_printf("(C) 2012 ATMEL Corp\n");
lcd_printf("at91support@atmel.com\n");
lcd_printf("%s CPU at %s MHz\n",
get_cpu_name(),
strmhz(temp, get_cpu_clk_rate()));
dram_size = 0;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
dram_size += gd->bd->bi_dram[i].size;
nand_size = 0;
for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
nand_size += get_nand_dev_by_index(i)->size;
lcd_printf(" %ld MB SDRAM, %ld MB NAND\n",
dram_size >> 20,
nand_size >> 20);
}
}
#endif /* CONFIG_LCD_INFO */
#endif /* CONFIG_LCD */
#ifdef CONFIG_DEBUG_UART_BOARD_INIT
void board_debug_uart_init(void)
{
at91_seriald_hw_init();
}
#endif
#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
#ifdef CONFIG_DEBUG_UART
debug_uart_init();
#endif
return 0;
}
#endif
int board_init(void)
{
/* arch number of AT91SAM9X5EK-Board */
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9X5EK;
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_CMD_NAND
at91sam9x5ek_nand_hw_init();
#endif
#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI_HCD)
at91_uhp_hw_init();
#endif
#ifdef CONFIG_LCD
at91sam9x5ek_lcd_hw_init();
#endif
return 0;
}
int dram_init(void)
{
gd->ram_size = get_ram_size((void *) CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
#if defined(CONFIG_SPL_BUILD)
#include <spl.h>
#include <nand.h>
void at91_spl_board_init(void)
{
#ifdef CONFIG_SYS_USE_MMC
at91_mci_hw_init();
#elif CONFIG_SYS_USE_NANDFLASH
at91sam9x5ek_nand_hw_init();
#endif
}
#include <asm/arch/atmel_mpddrc.h>
static void ddr2_conf(struct atmel_mpddrc_config *ddr2)
{
ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
ATMEL_MPDDRC_CR_NR_ROW_13 |
ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
ATMEL_MPDDRC_CR_NB_8BANKS |
ATMEL_MPDDRC_CR_DECOD_INTERLEAVED);
ddr2->rtr = 0x411;
ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |
2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |
2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET |
8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET |
2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET |
2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET |
2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET |
2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);
ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET |
200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
19 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
18 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
ddr2->tpr2 = (7 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET |
2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
}
void mem_init(void)
{
struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
struct atmel_mpddrc_config ddr2;
unsigned long csa;
ddr2_conf(&ddr2);
/* enable DDR2 clock */
writel(AT91_PMC_DDR, &pmc->scer);
/* Chip select 1 is for DDR2/SDRAM */
csa = readl(&matrix->ebicsa);
csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
csa &= ~AT91_MATRIX_EBI_DBPU_OFF;
csa |= AT91_MATRIX_EBI_DBPD_OFF;
csa |= AT91_MATRIX_EBI_EBI_IOSR_NORMAL;
writel(csa, &matrix->ebicsa);
/* DDRAM2 Controller initialize */
ddr2_init(ATMEL_BASE_DDRSDRC, ATMEL_BASE_CS1, &ddr2);
}
#endif