blob: 7bdc33df6215999aee8ec746ee0d767305d371bc [file] [log] [blame]
/*
* Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
*
* Based on davinci_dvevm.h. Original Copyrights follow:
*
* Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
*
* SPDX-License-Identifier: GPL-2.0
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* Board
*/
#define CONFIG_DRIVER_TI_EMAC
#undef CONFIG_USE_SPIFLASH
#undef CONFIG_SYS_USE_NOR
#define CONFIG_USE_NAND
/*
* Disable DM_* for SPL build and can be re-enabled after adding
* DM support in SPL
*/
#ifdef CONFIG_SPL_BUILD
#undef CONFIG_DM_I2C
#undef CONFIG_DM_I2C_COMPAT
#endif
/*
* SoC Configuration
*/
#define CONFIG_MACH_OMAPL138_LCDK
#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
#define CONFIG_SYS_OSCIN_FREQ 24000000
#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
#define CONFIG_SYS_HZ 1000
#define CONFIG_SKIP_LOWLEVEL_INIT
/*
* Memory Info
*/
#define CONFIG_SYS_MALLOC_LEN (0x10000 + 1*1024*1024) /* malloc() len */
#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
#define PHYS_SDRAM_1_SIZE (128 << 20) /* SDRAM size 128MB */
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
/* memtest start addr */
#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000)
/* memtest will be run on 16MB */
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \
DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \
DAVINCI_SYSCFG_SUSPSRC_SPI1 | \
DAVINCI_SYSCFG_SUSPSRC_UART2 | \
DAVINCI_SYSCFG_SUSPSRC_EMAC | \
DAVINCI_SYSCFG_SUSPSRC_I2C)
/*
* PLL configuration
*/
/* Requires CONFIG_SYS_DA850_PLL0_POSTDIV=0, set in Kconfig */
#define CONFIG_SYS_DA850_PLL0_PLLM 18
#define CONFIG_SYS_DA850_PLL1_PLLM 21
/*
* DDR2 memory configuration
*/
#define CONFIG_SYS_DA850_DDR2_DDRPHYCR (DV_DDR_PHY_PWRDNEN | \
DV_DDR_PHY_EXT_STRBEN | \
(0x5 << DV_DDR_PHY_RD_LATENCY_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDBCR ( \
(1 << DV_DDR_SDCR_DDR2EN_SHIFT) | \
(1 << DV_DDR_SDCR_DDREN_SHIFT) | \
(1 << DV_DDR_SDCR_SDRAMEN_SHIFT) | \
(1 << DV_DDR_SDCR_BUS_WIDTH_SHIFT) | \
(4 << DV_DDR_SDCR_CL_SHIFT) | \
(3 << DV_DDR_SDCR_IBANK_SHIFT) | \
(2 << DV_DDR_SDCR_PAGESIZE_SHIFT))
/* SDBCR2 is only used if IBANK_POS bit in SDBCR is set */
#define CONFIG_SYS_DA850_DDR2_SDBCR2 0
#define CONFIG_SYS_DA850_DDR2_SDTIMR ( \
(19 << DV_DDR_SDTMR1_RFC_SHIFT) | \
(1 << DV_DDR_SDTMR1_RP_SHIFT) | \
(1 << DV_DDR_SDTMR1_RCD_SHIFT) | \
(2 << DV_DDR_SDTMR1_WR_SHIFT) | \
(6 << DV_DDR_SDTMR1_RAS_SHIFT) | \
(8 << DV_DDR_SDTMR1_RC_SHIFT) | \
(1 << DV_DDR_SDTMR1_RRD_SHIFT) | \
(1 << DV_DDR_SDTMR1_WTR_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDTIMR2 ( \
(7 << DV_DDR_SDTMR2_RASMAX_SHIFT) | \
(2 << DV_DDR_SDTMR2_XP_SHIFT) | \
(0 << DV_DDR_SDTMR2_ODT_SHIFT) | \
(20 << DV_DDR_SDTMR2_XSNR_SHIFT) | \
(199 << DV_DDR_SDTMR2_XSRD_SHIFT) | \
(1 << DV_DDR_SDTMR2_RTP_SHIFT) | \
(2 << DV_DDR_SDTMR2_CKE_SHIFT))
#define CONFIG_SYS_DA850_DDR2_SDRCR 0x00000492
#define CONFIG_SYS_DA850_DDR2_PBBPR 0x30
/*
* Serial Driver info
*/
#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
#if !defined(CONFIG_DM_SERIAL)
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */
#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART2_BASE /* Base address of UART2 */
#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#endif
#define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE
#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID)
#define CONFIG_SF_DEFAULT_SPEED 30000000
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#ifdef CONFIG_USE_SPIFLASH
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x8000
#define CONFIG_SYS_SPI_U_BOOT_SIZE 0x30000
#endif
/*
* I2C Configuration
*/
#define CONFIG_SYS_I2C_DAVINCI
#define CONFIG_SYS_DAVINCI_I2C_SPEED 25000
#define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
#define CONFIG_SYS_I2C_EXPANDER_ADDR 0x20
/*
* Flash & Environment
*/
#ifdef CONFIG_USE_NAND
#define CONFIG_NAND_DAVINCI
#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
#define CONFIG_ENV_SIZE (128 << 9)
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
#define CONFIG_SYS_NAND_PAGE_2K
#define CONFIG_SYS_NAND_CS 3
#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE
#define CONFIG_SYS_NAND_MASK_CLE 0x10
#define CONFIG_SYS_NAND_MASK_ALE 0x8
#undef CONFIG_SYS_NAND_HW_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define CONFIG_SYS_NAND_HW_ECC_OOBFIRST
#define CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE (2 << 10)
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 << 10)
#define CONFIG_SYS_NAND_U_BOOT_SIZE SZ_512K
#define CONFIG_SYS_NAND_U_BOOT_DST 0xc1080000
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_DST - \
CONFIG_SYS_NAND_U_BOOT_SIZE - \
CONFIG_SYS_MALLOC_LEN - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_NAND_ECCPOS { \
6, 7, 8, 9, 10, 11, 12, 13, 14, 15, \
22, 23, 24, 25, 26, 27, 28, 29, 30, 31, \
38, 39, 40, 41, 42, 43, 44, 45, 46, 47, \
54, 55, 56, 57, 58, 59, 60, 61, 62, 63 }
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 10
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SPL_NAND_BASE
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_ECC
#define CONFIG_SPL_NAND_LOAD
#endif
#ifdef CONFIG_SYS_USE_NOR
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
#define CONFIG_SYS_FLASH_SECT_SZ (128 << 10) /* 128KB */
#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ * 3)
#define CONFIG_ENV_SIZE (128 << 10)
#define CONFIG_SYS_FLASH_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
#define PHYS_FLASH_SIZE (8 << 20) /* Flash size 8MB */
#define CONFIG_SYS_MAX_FLASH_SECT ((PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)\
+ 3)
#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ
#endif
#ifdef CONFIG_USE_SPIFLASH
#define CONFIG_ENV_SIZE (64 << 10)
#define CONFIG_ENV_OFFSET (256 << 10)
#define CONFIG_ENV_SECT_SIZE (64 << 10)
#endif
/*
* Network & Ethernet Configuration
*/
#ifdef CONFIG_DRIVER_TI_EMAC
#define CONFIG_MII
#undef CONFIG_DRIVER_TI_EMAC_USE_RMII
#define CONFIG_BOOTP_DEFAULT
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
#endif
/*
* U-Boot general configuration
*/
#define CONFIG_MISC_INIT_R
#define CONFIG_BOOTFILE "zImage" /* Boot file name */
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000)
#define CONFIG_MX_CYCLIC
/*
* Linux Information
*/
#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
#define CONFIG_CMDLINE_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTCOMMAND \
"run envboot; " \
"run mmcboot; "
#define DEFAULT_LINUX_BOOT_ENV \
"loadaddr=0xc0700000\0" \
"fdtaddr=0xc0600000\0" \
"scriptaddr=0xc0600000\0"
#include <environment/ti/mmc.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
DEFAULT_MMC_TI_ARGS \
"bootpart=0:2\0" \
"bootdir=/boot\0" \
"bootfile=zImage\0" \
"fdtfile=da850-lcdk.dtb\0" \
"boot_fdt=yes\0" \
"boot_fit=0\0" \
"console=ttyS2,115200n8\0"
#ifdef CONFIG_CMD_BDI
#define CONFIG_CLOCKS
#endif
#ifndef CONFIG_DRIVER_TI_EMAC
#endif
#ifdef CONFIG_USE_NAND
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#endif
#if !defined(CONFIG_USE_NAND) && \
!defined(CONFIG_SYS_USE_NOR) && \
!defined(CONFIG_USE_SPIFLASH)
#define CONFIG_ENV_SIZE (16 << 10)
#endif
/* SD/MMC */
#ifdef CONFIG_ENV_IS_IN_MMC
#undef CONFIG_ENV_SIZE
#undef CONFIG_ENV_OFFSET
#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
#define CONFIG_ENV_OFFSET (51 << 9) /* Sector 51 */
#endif
#ifndef CONFIG_DIRECT_NOR_BOOT
/* defines for SPL */
#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE - \
CONFIG_SYS_MALLOC_LEN)
#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN
#define CONFIG_SPL_STACK 0x8001ff00
#define CONFIG_SPL_TEXT_BASE 0x80000000
#define CONFIG_SPL_MAX_FOOTPRINT 32768
#define CONFIG_SPL_PAD_TO 32768
#endif
/* additions for new relocation code, must added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0xc0000000
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - /* Fix this */ \
GENERATED_GBL_DATA_SIZE)
#include <asm/arch/hardware.h>
#endif /* __CONFIG_H */