| /* |
| * (C) Copyright 2009 |
| * Dirk Eibach, Guntermann & Drunck GmbH, eibach@gdsys.de |
| * |
| * Based on include/configs/canyonlands.h |
| * (C) Copyright 2008 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * intip.h - configuration for CompactCenter aka intip (460EX) and DevCon-Center |
| */ |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| */ |
| /* |
| * This config file is used for CompactCenter(codename intip) and DevCon-Center |
| */ |
| #define CONFIG_460EX 1 /* Specific PPC460EX */ |
| #ifdef CONFIG_DEVCONCENTER |
| #define CONFIG_HOSTNAME devconcenter |
| #define CONFIG_IDENT_STRING " devconcenter 0.06" |
| #else |
| #define CONFIG_HOSTNAME intip |
| #define CONFIG_IDENT_STRING " intip 0.06" |
| #endif |
| #define CONFIG_440 1 |
| |
| #ifndef CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_TEXT_BASE 0xFFFA0000 |
| #endif |
| |
| /* |
| * Include common defines/options for all AMCC eval boards |
| */ |
| #include "amcc-common.h" |
| |
| #define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */ |
| |
| #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ |
| #define CONFIG_BOARD_EARLY_INIT_R 1 /* Call board_early_init_r */ |
| #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ |
| #define CONFIG_BOARD_TYPES 1 /* support board types */ |
| #define CFG_ALT_MEMTEST |
| |
| #undef CONFIG_ZERO_BOOTDELAY_CHECK /* ignore keypress on bootdelay==0 */ |
| |
| /* |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| */ |
| #define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ |
| #define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ |
| #define CONFIG_SYS_PCI_TARGBASE CONFIG_SYS_PCI_MEMBASE |
| |
| /* EBC stuff */ |
| #ifdef CONFIG_DEVCONCENTER /* Devcon-Center has 128 MB of flash */ |
| #define CONFIG_SYS_FLASH_BASE 0xF8000000 /* later mapped here */ |
| #define CONFIG_SYS_FLASH_SIZE (128 << 20) |
| #else |
| #define CONFIG_SYS_FLASH_BASE 0xFC000000 /* later mapped here */ |
| #define CONFIG_SYS_FLASH_SIZE (64 << 20) |
| #endif |
| |
| #define CONFIG_SYS_NVRAM_BASE 0xE0000000 |
| #define CONFIG_SYS_UART_BASE 0xE0100000 |
| #define CONFIG_SYS_IO_BASE 0xE0200000 |
| |
| #define CONFIG_SYS_BOOT_BASE_ADDR 0xFF000000 /* EBC Boot Space */ |
| #define CONFIG_SYS_FLASH_BASE_PHYS_H 0x4 |
| #ifdef CONFIG_DEVCONCENTER /* Devcon-Center has 128 MB of flash */ |
| #define CONFIG_SYS_FLASH_BASE_PHYS_L 0xC8000000 |
| #else |
| #define CONFIG_SYS_FLASH_BASE_PHYS_L 0xCC000000 |
| #endif |
| #define CONFIG_SYS_FLASH_BASE_PHYS \ |
| (((u64)CONFIG_SYS_FLASH_BASE_PHYS_H << 32) \ |
| | (u64)CONFIG_SYS_FLASH_BASE_PHYS_L) |
| |
| #define CONFIG_SYS_OCM_BASE 0xE3000000 /* OCM: 64k */ |
| #define CONFIG_SYS_SRAM_BASE 0xE8000000 /* SRAM: 256k */ |
| #define CONFIG_SYS_SRAM_SIZE (256 << 10) |
| #define CONFIG_SYS_LOCAL_CONF_REGS 0xEF000000 |
| |
| #define CONFIG_SYS_AHB_BASE 0xE2000000 /* int. AHB periph. */ |
| |
| /* |
| * Initial RAM & stack pointer (placed in OCM) |
| */ |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ |
| #define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) |
| #define CONFIG_SYS_GBL_DATA_OFFSET \ |
| (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_CONS_INDEX 1 /* Use UART0 */ |
| |
| /* |
| * Environment |
| */ |
| /* |
| * Define here the location of the environment variables (FLASH). |
| */ |
| #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ |
| #define CONFIG_SYS_NOR_CS 0 /* NOR chip connected to CSx */ |
| |
| /* |
| * FLASH related |
| */ |
| #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ |
| #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ |
| #define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* Use AMD reset cmd */ |
| |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ |
| #ifdef CONFIG_DEVCONCENTER |
| #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* max num of sectors per chip*/ |
| #else |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sectors per chip*/ |
| #endif |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase/ms */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write/ms */ |
| |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* buff'd writes (20x faster) */ |
| #define CONFIG_SYS_FLASH_EMPTY_INFO /* 'E' for empty sector on flinfo */ |
| |
| #ifdef CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector*/ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR - CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| #endif /* CONFIG_ENV_IS_IN_FLASH */ |
| |
| /* |
| * DDR SDRAM |
| */ |
| |
| #define CONFIG_AUTOCALIB "silent\0" /* default is non-verbose */ |
| |
| #define CONFIG_PPC4xx_DDR_AUTOCALIBRATION /* IBM DDR autocalibration */ |
| #define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */ |
| #undef CONFIG_PPC4xx_DDR_METHOD_A |
| |
| /* DDR1/2 SDRAM Device Control Register Data Values */ |
| /* Memory Queue */ |
| #define CONFIG_SYS_SDRAM_R0BAS 0x0000f800 |
| #define CONFIG_SYS_SDRAM_R1BAS 0x00000000 |
| #define CONFIG_SYS_SDRAM_R2BAS 0x00000000 |
| #define CONFIG_SYS_SDRAM_R3BAS 0x00000000 |
| #define CONFIG_SYS_SDRAM_PLBADDULL 0x00000000 |
| #define CONFIG_SYS_SDRAM_PLBADDUHB 0x00000008 |
| #define CONFIG_SYS_SDRAM_CONF1LL 0x80001C00 |
| #define CONFIG_SYS_SDRAM_CONF1HB 0x80001C80 |
| #define CONFIG_SYS_SDRAM_CONFPATHB 0x10a68000 |
| |
| /* SDRAM Controller */ |
| #define CONFIG_SYS_SDRAM0_MB0CF 0x00000201 |
| #define CONFIG_SYS_SDRAM0_MB1CF 0x00000000 |
| #define CONFIG_SYS_SDRAM0_MB2CF 0x00000000 |
| #define CONFIG_SYS_SDRAM0_MB3CF 0x00000000 |
| #define CONFIG_SYS_SDRAM0_MCOPT1 0x05120000 |
| #define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000 |
| #define CONFIG_SYS_SDRAM0_MODT0 0x00000000 |
| #define CONFIG_SYS_SDRAM0_MODT1 0x00000000 |
| #define CONFIG_SYS_SDRAM0_MODT2 0x00000000 |
| #define CONFIG_SYS_SDRAM0_MODT3 0x00000000 |
| #define CONFIG_SYS_SDRAM0_CODT 0x00000020 |
| #define CONFIG_SYS_SDRAM0_RTR 0x06180000 |
| #define CONFIG_SYS_SDRAM0_INITPLR0 0xA8380000 |
| #define CONFIG_SYS_SDRAM0_INITPLR1 0x81900400 |
| #define CONFIG_SYS_SDRAM0_INITPLR2 0x81020000 |
| #define CONFIG_SYS_SDRAM0_INITPLR3 0x81030000 |
| #define CONFIG_SYS_SDRAM0_INITPLR4 0x81010002 |
| #define CONFIG_SYS_SDRAM0_INITPLR5 0xE4000552 |
| #define CONFIG_SYS_SDRAM0_INITPLR6 0x81900400 |
| #define CONFIG_SYS_SDRAM0_INITPLR7 0x8A880000 |
| #define CONFIG_SYS_SDRAM0_INITPLR8 0x8A880000 |
| #define CONFIG_SYS_SDRAM0_INITPLR9 0x8A880000 |
| #define CONFIG_SYS_SDRAM0_INITPLR10 0x8A880000 |
| #define CONFIG_SYS_SDRAM0_INITPLR11 0x81000452 |
| #define CONFIG_SYS_SDRAM0_INITPLR12 0x81010382 |
| #define CONFIG_SYS_SDRAM0_INITPLR13 0x81010002 |
| #define CONFIG_SYS_SDRAM0_INITPLR14 0x00000000 |
| #define CONFIG_SYS_SDRAM0_INITPLR15 0x00000000 |
| #define CONFIG_SYS_SDRAM0_RQDC 0x80000038 |
| #define CONFIG_SYS_SDRAM0_RFDC 0x00000257 |
| #define CONFIG_SYS_SDRAM0_RDCC 0x40000000 |
| #define CONFIG_SYS_SDRAM0_DLCR 0x00000000 |
| #define CONFIG_SYS_SDRAM0_CLKTR 0x40000000 |
| #define CONFIG_SYS_SDRAM0_WRDTR 0x86000823 |
| #define CONFIG_SYS_SDRAM0_SDTR1 0x80201000 |
| #define CONFIG_SYS_SDRAM0_SDTR2 0x32204232 |
| #define CONFIG_SYS_SDRAM0_SDTR3 0x090C0D15 |
| #define CONFIG_SYS_SDRAM0_MMODE 0x00000452 |
| #define CONFIG_SYS_SDRAM0_MEMODE 0x00000002 |
| |
| #define CONFIG_SYS_MBYTES_SDRAM 256 /* 256MB */ |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 |
| |
| /* I2C bootstrap EEPROM */ |
| #define CONFIG_4xx_CONFIG_I2C_EEPROM_ADDR 0x54 |
| #define CONFIG_4xx_CONFIG_I2C_EEPROM_OFFSET 0 |
| #define CONFIG_4xx_CONFIG_BLOCKSIZE 16 |
| |
| /* I2C SYSMON */ |
| #define CONFIG_DTT_LM63 1 /* National LM63 */ |
| #define CONFIG_DTT_SENSORS { 0 } /* Sensor addresses */ |
| #define CONFIG_DTT_PWM_LOOKUPTABLE \ |
| { { 40, 10 }, { 50, 20 }, { 60, 40 } } |
| #define CONFIG_DTT_TACH_LIMIT 0xa10 |
| |
| /* RTC configuration */ |
| #define CONFIG_RTC_DS1337 1 |
| #define CONFIG_SYS_I2C_RTC_ADDR 0x68 |
| |
| /* |
| * Ethernet |
| */ |
| #define CONFIG_IBM_EMAC4_V4 1 |
| |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_HAS_ETH1 |
| |
| #define CONFIG_PHY_ADDR 2 /* PHY address, See schematics */ |
| #define CONFIG_PHY1_ADDR 3 |
| |
| #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ |
| #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ |
| #define CONFIG_PHY_DYNAMIC_ANEG 1 |
| |
| /* |
| * USB-OHCI |
| */ |
| #define CONFIG_USB_OHCI_NEW |
| #define CONFIG_USB_STORAGE |
| #undef CONFIG_SYS_OHCI_BE_CONTROLLER /* 460EX has little endian descriptors*/ |
| #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS /* 460EX has little endian register */ |
| #define CONFIG_SYS_OHCI_USE_NPS /* force NoPowerSwitching mode */ |
| #define CONFIG_SYS_USB_OHCI_REGS_BASE (CONFIG_SYS_AHB_BASE | 0xd0000) |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 |
| |
| /* |
| * Default environment variables |
| */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_AMCC_DEF_ENV \ |
| CONFIG_AMCC_DEF_ENV_POWERPC \ |
| CONFIG_AMCC_DEF_ENV_NOR_UPD \ |
| "kernel_addr=fc000000\0" \ |
| "fdt_addr=fc1e0000\0" \ |
| "ramdisk_addr=fc200000\0" \ |
| "pciconfighost=1\0" \ |
| "pcie_mode=RP:RP\0" \ |
| "" |
| |
| /* |
| * Commands additional to the ones defined in amcc-common.h |
| */ |
| #define CONFIG_CMD_CHIP_CONFIG |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_DTT |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_CMD_FAT |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_SDRAM |
| #define CONFIG_CMD_SNTP |
| #define CONFIG_CMD_USB |
| |
| /* Partitions */ |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_ISO_PARTITION |
| |
| /* |
| * PCI stuff |
| */ |
| /* General PCI */ |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CONFIG_PCI_CONFIG_HOST_BRIDGE |
| #define CONFIG_PCI_DISABLE_PCIE |
| |
| /* Board-specific PCI */ |
| #define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ |
| #undef CONFIG_SYS_PCI_MASTER_INIT |
| |
| #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ |
| #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ |
| |
| |
| /* |
| * External Bus Controller (EBC) Setup |
| */ |
| |
| /* |
| * CompactCenter has 64MBytes of NOR FLASH (Spansion 29GL512), but the |
| * boot EBC mapping only supports a maximum of 16MBytes |
| * (4.ff00.0000 - 4.ffff.ffff). |
| * To solve this problem, the FLASH has to get remapped to another |
| * EBC address which accepts bigger regions: |
| * |
| * 0xfc00.0000 -> 4.cc00.0000 |
| */ |
| |
| |
| /* Memory Bank 0 (NOR-FLASH) initialization */ |
| #define CONFIG_SYS_EBC_PB0AP 0x10055e00 |
| #define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000) |
| |
| /* Memory Bank 1 (NVRAM) initialization */ |
| #define CONFIG_SYS_EBC_PB1AP 0x02815480 |
| /* BAS=NVRAM,BS=1MB,BU=R/W,BW=8bit*/ |
| #define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NVRAM_BASE | 0x18000) |
| |
| /* Memory Bank 2 (UART) initialization */ |
| #define CONFIG_SYS_EBC_PB2AP 0x02815480 |
| /* BAS=UART,BS=1MB,BU=R/W,BW=16bit*/ |
| #define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_UART_BASE | 0x1A000) |
| |
| /* Memory Bank 3 (IO) initialization */ |
| #define CONFIG_SYS_EBC_PB3AP 0x02815480 |
| /* BAS=IO,BS=1MB,BU=R/W,BW=16bit*/ |
| #define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_IO_BASE | 0x1A000) |
| |
| /* |
| * PPC4xx GPIO Configuration |
| */ |
| /* 460EX: Use USB configuration */ |
| #define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ |
| { \ |
| /* GPIO Core 0 */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 GMC1TxD(0) USB2HostD(0) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO1 GMC1TxD(1) USB2HostD(1) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO2 GMC1TxD(2) USB2HostD(2) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO3 GMC1TxD(3) USB2HostD(3) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO4 GMC1TxD(4) USB2HostD(4) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO5 GMC1TxD(5) USB2HostD(5) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO6 GMC1TxD(6) USB2HostD(6) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO7 GMC1TxD(7) USB2HostD(7) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 GMC1RxD(0) USB2OTGD(0) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 GMC1RxD(1) USB2OTGD(1) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 GMC1RxD(2) USB2OTGD(2) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO11 GMC1RxD(3) USB2OTGD(3) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO12 GMC1RxD(4) USB2OTGD(4) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO13 GMC1RxD(5) USB2OTGD(5) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO14 GMC1RxD(6) USB2OTGD(6) */ \ |
| {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO15 GMC1RxD(7) USB2OTGD(7) */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_SEL, GPIO_OUT_0}, /* GPIO16 GMC1TxER USB2HostStop */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 GMC1CD USB2HostNext */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 GMC1RxER USB2HostDir */ \ |
| {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO19 GMC1TxEN USB2OTGStop */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO20 GMC1CRS USB2OTGNext */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO21 GMC1RxDV USB2OTGDir */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO22 NFRDY */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO23 NFREN */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO24 NFWEN */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO25 NFCLE */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 NFALE */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO27 IRQ(0) */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO28 IRQ(1) */ \ |
| {GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO29 IRQ(2) */ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO30 PerPar0 DMAReq2 IRQ(7)*/ \ |
| {GPIO0_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO31 PerPar1 DMAAck2 IRQ(8)*/ \ |
| }, \ |
| { \ |
| /* GPIO Core 1 */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO32 PerPar2 EOT2/TC2 IRQ(9)*/ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO33 PerPar3 DMAReq3 IRQ(4)*/ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT3, GPIO_OUT_1}, /* GPIO34 UART0_DCD_N UART1_DSR_CTS_N UART2_SOUT*/ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO35 UART0_8PIN_DSR_N UART1_RTS_DTR_N UART2_SIN*/ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO36 UART0_8PIN_CTS_N DMAAck3 UART3_SIN*/ \ |
| {GPIO1_BASE, GPIO_BI , GPIO_ALT2, GPIO_OUT_0}, /* GPIO37 UART0_RTS_N EOT3/TC3 UART3_SOUT*/ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO38 UART0_DTR_N UART1_SOUT */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT2, GPIO_OUT_0}, /* GPIO39 UART0_RI_N UART1_SIN */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO40 IRQ(3) */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO41 CS(1) */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO42 CS(2) */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO43 CS(3) DMAReq1 IRQ(10)*/ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO44 CS(4) DMAAck1 IRQ(11)*/ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_ALT3, GPIO_OUT_0}, /* GPIO45 CS(5) EOT/TC1 IRQ(12)*/ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO46 PerAddr(5) DMAReq0 IRQ(13)*/ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO47 PerAddr(6) DMAAck0 IRQ(14)*/ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO48 PerAddr(7) EOT/TC0 IRQ(15)*/ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO49 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO50 USB_SERVICE_SUSPEND_N */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO51 SPI_CSS_N */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO52 FPGA_PROGRAM_UC_N */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO53 FPGA_INIT_UC_N */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO54 WD_STROBE */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO55 LED_2_OUT */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO56 LED_1_OUT */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO57 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO61 STARTUP_FINISHED_N */ \ |
| {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO62 STARTUP_FINISHED */ \ |
| {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO63 SERVICE_PORT_ACTIVE */ \ |
| } \ |
| } |
| |
| #endif /* __CONFIG_H */ |