| menu "mpc85xx CPU" |
| depends on MPC85xx |
| |
| config SYS_CPU |
| default "mpc85xx" |
| |
| config CMD_ERRATA |
| bool "Enable the 'errata' command" |
| depends on MPC85xx |
| default y |
| help |
| This enables the 'errata' command which displays a list of errata |
| work-arounds which are enabled for the current board. |
| |
| config FSL_PREPBL_ESDHC_BOOT_SECTOR |
| bool "Generate QorIQ pre-PBL eSDHC boot sector" |
| depends on MPC85xx |
| depends on SDCARD |
| help |
| With this option final image would have prepended QorIQ pre-PBL eSDHC |
| boot sector suitable for SD card images. This boot sector instruct |
| BootROM to configure L2 SRAM and eSDHC then load image from SD card |
| into L2 SRAM and finally jump to image entry point. |
| |
| This is alternative to Freescale boot_format tool, but works only for |
| SD card images and only for L2 SRAM booting. U-Boot images generated |
| with this option should not passed to boot_format tool. |
| |
| For other configuration like booting from eSPI or configuring SDRAM |
| please use Freescale boot_format tool without this option. See file |
| doc/README.mpc85xx-sd-spi-boot |
| |
| config FSL_PREPBL_ESDHC_BOOT_SECTOR_START |
| int "QorIQ pre-PBL eSDHC boot sector start offset" |
| depends on FSL_PREPBL_ESDHC_BOOT_SECTOR |
| range 0 23 |
| default 0 |
| help |
| QorIQ pre-PBL eSDHC boot sector may be located on one of the first |
| 24 SD card sectors. Select SD card sector on which final U-Boot |
| image (with this boot sector) would be installed. |
| |
| By default first SD card sector (0) is used. But this may be changed |
| to allow installing U-Boot image on some partition (with fixed start |
| sector). |
| |
| Please note that any sector on SD card prior this boot sector must |
| not contain ASCII "BOOT" bytes at sector offset 0x40. |
| |
| config FSL_PREPBL_ESDHC_BOOT_SECTOR_DATA |
| int "Relative data sector for QorIQ pre-PBL eSDHC boot sector" |
| depends on FSL_PREPBL_ESDHC_BOOT_SECTOR |
| default 1 |
| range 1 8388607 |
| help |
| Select data sector from the beginning of QorIQ pre-PBL eSDHC boot |
| sector on which would be stored raw U-Boot image. |
| |
| By default is it second sector (1) which is the first available free |
| sector (on the first sector is stored boot sector). It can be any |
| sector number which offset in bytes can be expressed by 32-bit number. |
| |
| In case this final U-Boot image (with this boot sector) is put on |
| the FAT32 partition into reserved boot area, this data sector needs |
| to be at least 2 (third sector) because FAT32 use second sector for |
| its data. |
| |
| choice |
| prompt "Target select" |
| optional |
| |
| config TARGET_SOCRATES |
| bool "Support socrates" |
| select ARCH_MPC8544 |
| |
| config TARGET_P3041DS |
| bool "Support P3041DS" |
| select PHYS_64BIT |
| select ARCH_P3041 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select FSL_NGPIXIS |
| imply CMD_SATA |
| imply PANIC_HANG |
| |
| config TARGET_P4080DS |
| bool "Support P4080DS" |
| select PHYS_64BIT |
| select ARCH_P4080 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select FSL_NGPIXIS |
| imply CMD_SATA |
| imply PANIC_HANG |
| |
| config TARGET_P5040DS |
| bool "Support P5040DS" |
| select PHYS_64BIT |
| select ARCH_P5040 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select FSL_NGPIXIS |
| select SYS_FSL_RAID_ENGINE |
| imply CMD_SATA |
| imply PANIC_HANG |
| |
| config TARGET_MPC8548CDS |
| bool "Support MPC8548CDS" |
| select ARCH_MPC8548 |
| select FSL_VIA |
| select SYS_CACHE_SHIFT_5 |
| |
| config TARGET_P1010RDB_PA |
| bool "Support P1010RDB_PA" |
| select ARCH_P1010 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select SUPPORT_SPL |
| select SUPPORT_TPL |
| select SYS_L2_SIZE_256KB |
| imply CMD_EEPROM |
| imply CMD_SATA |
| imply PANIC_HANG |
| |
| config TARGET_P1010RDB_PB |
| bool "Support P1010RDB_PB" |
| select ARCH_P1010 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select SUPPORT_SPL |
| select SUPPORT_TPL |
| select SYS_L2_SIZE_256KB |
| imply CMD_EEPROM |
| imply CMD_SATA |
| imply PANIC_HANG |
| |
| config TARGET_P1020RDB_PC |
| bool "Support P1020RDB-PC" |
| select SUPPORT_SPL |
| select SUPPORT_TPL |
| select ARCH_P1020 |
| select SYS_L2_SIZE_256KB |
| imply CMD_EEPROM |
| imply CMD_SATA |
| imply PANIC_HANG |
| |
| config TARGET_P1020RDB_PD |
| bool "Support P1020RDB-PD" |
| select SUPPORT_SPL |
| select SUPPORT_TPL |
| select ARCH_P1020 |
| select SYS_L2_SIZE_256KB |
| imply CMD_EEPROM |
| imply CMD_SATA |
| imply PANIC_HANG |
| |
| config TARGET_P2020RDB |
| bool "Support P2020RDB-PC" |
| select SUPPORT_SPL |
| select SUPPORT_TPL |
| select ARCH_P2020 |
| select SYS_L2_SIZE_512KB |
| imply CMD_EEPROM |
| imply CMD_SATA |
| imply SATA_SIL |
| |
| config TARGET_P2041RDB |
| bool "Support P2041RDB" |
| select ARCH_P2041 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select FSL_CORENET |
| select PHYS_64BIT |
| select SYS_L3_SIZE_1024KB |
| imply CMD_SATA |
| imply FSL_SATA |
| |
| config TARGET_QEMU_PPCE500 |
| bool "Support qemu-ppce500" |
| select ARCH_QEMU_E500 |
| select PHYS_64BIT |
| select SYS_RAMBOOT |
| imply OF_HAS_PRIOR_STAGE |
| |
| config TARGET_T1024RDB |
| bool "Support T1024RDB" |
| select ARCH_T1024 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select SUPPORT_SPL |
| select PHYS_64BIT |
| select FSL_DDR_INTERACTIVE |
| select SYS_L3_SIZE_256KB |
| imply CMD_EEPROM |
| imply PANIC_HANG |
| |
| config TARGET_T1042RDB |
| bool "Support T1042RDB" |
| select ARCH_T1042 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select SUPPORT_SPL |
| select PHYS_64BIT |
| select SYS_L3_SIZE_256KB |
| |
| config TARGET_T1042D4RDB |
| bool "Support T1042D4RDB" |
| select ARCH_T1042 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select SUPPORT_SPL |
| select PHYS_64BIT |
| select SYS_L3_SIZE_256KB |
| imply PANIC_HANG |
| |
| config TARGET_T1042RDB_PI |
| bool "Support T1042RDB_PI" |
| select ARCH_T1042 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select SUPPORT_SPL |
| select PHYS_64BIT |
| select SYS_L3_SIZE_256KB |
| imply PANIC_HANG |
| |
| config TARGET_T2080QDS |
| bool "Support T2080QDS" |
| select ARCH_T2080 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select SUPPORT_SPL |
| select PHYS_64BIT |
| select FSL_DDR_FIRST_SLOT_QUAD_CAPABLE |
| select FSL_DDR_INTERACTIVE |
| select SYS_L3_SIZE_512KB |
| imply CMD_SATA |
| |
| config TARGET_T2080RDB |
| bool "Support T2080RDB" |
| select ARCH_T2080 |
| select BOARD_LATE_INIT if CHAIN_OF_TRUST |
| select SUPPORT_SPL |
| select PHYS_64BIT |
| select SYS_L3_SIZE_512KB |
| imply CMD_SATA |
| imply PANIC_HANG |
| |
| config TARGET_T4240RDB |
| bool "Support T4240RDB" |
| select ARCH_T4240 |
| select SUPPORT_SPL |
| select PHYS_64BIT |
| select FSL_DDR_FIRST_SLOT_QUAD_CAPABLE |
| select SYS_L3_SIZE_512KB |
| imply CMD_SATA |
| imply PANIC_HANG |
| |
| config TARGET_KMP204X |
| bool "Support kmp204x" |
| select VENDOR_KM |
| |
| config TARGET_KMCENT2 |
| bool "Support kmcent2" |
| select VENDOR_KM |
| select FSL_CORENET |
| select SYS_DPAA_FMAN |
| select SYS_DPAA_PME |
| select SYS_L3_SIZE_256KB |
| |
| endchoice |
| |
| config ARCH_B4420 |
| bool |
| select E500MC |
| select E6500 |
| select FSL_CORENET |
| select FSL_LAW |
| select HETROGENOUS_CLUSTERS |
| select SYS_FSL_DDR_VER_47 |
| select SYS_FSL_ERRATUM_A004477 |
| select SYS_FSL_ERRATUM_A005871 |
| select SYS_FSL_ERRATUM_A006379 |
| select SYS_FSL_ERRATUM_A006384 |
| select SYS_FSL_ERRATUM_A006475 |
| select SYS_FSL_ERRATUM_A006593 |
| select SYS_FSL_ERRATUM_A007075 |
| select SYS_FSL_ERRATUM_A007186 if CHAIN_OF_TRUST |
| select SYS_FSL_ERRATUM_A007212 |
| select SYS_FSL_ERRATUM_A009942 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_QORIQ_CHASSIS2 |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v24 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_QMAN_V3 if SYS_DPAA_QBMAN |
| select SYS_FSL_USB1_PHY_ENABLE |
| select SYS_PPC64 |
| select FSL_IFC |
| imply CMD_EEPROM |
| imply CMD_NAND |
| imply CMD_REGINFO |
| |
| config ARCH_B4860 |
| bool |
| select E500MC |
| select E6500 |
| select FSL_CORENET |
| select FSL_LAW |
| select HETROGENOUS_CLUSTERS |
| select SYS_FSL_DDR_VER_47 |
| select SYS_FSL_ERRATUM_A004477 |
| select SYS_FSL_ERRATUM_A005871 |
| select SYS_FSL_ERRATUM_A006379 |
| select SYS_FSL_ERRATUM_A006384 |
| select SYS_FSL_ERRATUM_A006475 |
| select SYS_FSL_ERRATUM_A006593 |
| select SYS_FSL_ERRATUM_A007075 |
| select SYS_FSL_ERRATUM_A007186 if CHAIN_OF_TRUST |
| select SYS_FSL_ERRATUM_A007212 |
| select SYS_FSL_ERRATUM_A007907 |
| select SYS_FSL_ERRATUM_A009942 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_QORIQ_CHASSIS2 |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v24 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_SRIO_LIODN |
| select SYS_FSL_QMAN_V3 if SYS_DPAA_QBMAN |
| select SYS_FSL_USB1_PHY_ENABLE |
| select SYS_PPC64 |
| select FSL_IFC |
| imply CMD_EEPROM |
| imply CMD_NAND |
| imply CMD_REGINFO |
| |
| config ARCH_BSC9131 |
| bool |
| select FSL_LAW |
| select SYS_FSL_DDR_VER_44 |
| select SYS_FSL_ERRATUM_A004477 |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select FSL_IFC |
| imply CMD_EEPROM |
| imply CMD_NAND |
| imply CMD_REGINFO |
| |
| config ARCH_BSC9132 |
| bool |
| select FSL_LAW |
| select SYS_FSL_DDR_VER_46 |
| select SYS_FSL_ERRATUM_A004477 |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_A005434 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_ERRATUM_I2C_A004447 |
| select SYS_FSL_ERRATUM_IFC_A002769 |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v22 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| select FSL_IFC |
| imply CMD_EEPROM |
| imply CMD_MTDPARTS |
| imply CMD_NAND |
| imply CMD_PCI |
| imply CMD_REGINFO |
| |
| config ARCH_C29X |
| bool |
| select FSL_LAW |
| select SYS_FSL_DDR_VER_46 |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_6 |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| select FSL_IFC |
| imply CMD_NAND |
| imply CMD_PCI |
| imply CMD_REGINFO |
| |
| config ARCH_MPC8536 |
| bool |
| select FSL_LAW |
| select SYS_FSL_ERRATUM_A004508 |
| select SYS_FSL_ERRATUM_A005125 |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR2 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_2 |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| select FSL_ELBC |
| imply CMD_NAND |
| imply CMD_SATA |
| imply CMD_REGINFO |
| |
| config ARCH_MPC8540 |
| bool |
| select FSL_LAW |
| select SYS_FSL_HAS_DDR1 |
| |
| config ARCH_MPC8544 |
| bool |
| select BTB |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_5 |
| select SYS_FSL_ERRATUM_A005125 |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR2 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_2 |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| select FSL_ELBC |
| |
| config ARCH_MPC8548 |
| bool |
| select BTB |
| select FSL_LAW |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_NMG_DDR120 |
| select SYS_FSL_ERRATUM_NMG_LBC103 |
| select SYS_FSL_ERRATUM_NMG_ETSEC129 |
| select SYS_FSL_ERRATUM_I2C_A004447 |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR2 |
| select SYS_FSL_HAS_DDR1 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_RMU |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_2 |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| imply CMD_REGINFO |
| |
| config ARCH_MPC8560 |
| bool |
| select FSL_LAW |
| select SYS_FSL_HAS_DDR1 |
| |
| config ARCH_P1010 |
| bool |
| select A003399_NOR_WORKAROUND if SYS_FSL_ERRATUM_IFC_A003399 && !SPL |
| select BTB |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_5 |
| select SYS_HAS_SERDES |
| select SYS_FSL_ERRATUM_A004477 |
| select SYS_FSL_ERRATUM_A004508 |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_A005275 |
| select SYS_FSL_ERRATUM_A006261 |
| select SYS_FSL_ERRATUM_A007075 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_ERRATUM_I2C_A004447 |
| select SYS_FSL_ERRATUM_IFC_A002769 |
| select SYS_FSL_ERRATUM_P1010_A003549 |
| select SYS_FSL_ERRATUM_SEC_A003571 |
| select SYS_FSL_ERRATUM_IFC_A003399 |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v22 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_USB1_PHY_ENABLE |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| select FSL_IFC |
| imply CMD_EEPROM |
| imply CMD_MTDPARTS |
| imply CMD_NAND |
| imply CMD_SATA |
| imply CMD_PCI |
| imply CMD_REGINFO |
| imply FSL_SATA |
| imply TIMESTAMP |
| |
| config ARCH_P1011 |
| bool |
| select FSL_LAW |
| select SYS_FSL_ERRATUM_A004508 |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_ELBC_A001 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select FSL_PCIE_DISABLE_ASPM |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_2 |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| select FSL_ELBC |
| |
| config ARCH_P1020 |
| bool |
| select BTB |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_5 |
| select SYS_FSL_ERRATUM_A004508 |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_ELBC_A001 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select FSL_PCIE_DISABLE_ASPM |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_2 |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| select FSL_ELBC |
| imply CMD_NAND |
| imply CMD_SATA |
| imply CMD_PCI |
| imply CMD_REGINFO |
| imply SATA_SIL |
| |
| config ARCH_P1021 |
| bool |
| select FSL_LAW |
| select SYS_FSL_ERRATUM_A004508 |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_ELBC_A001 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select FSL_PCIE_DISABLE_ASPM |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_2 |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| select FSL_ELBC |
| imply CMD_REGINFO |
| imply CMD_NAND |
| imply CMD_SATA |
| imply CMD_REGINFO |
| imply SATA_SIL |
| |
| config ARCH_P1023 |
| bool |
| select FSL_LAW |
| select SYS_FSL_ERRATUM_A004508 |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_I2C_A004447 |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v22 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select FSL_ELBC |
| |
| config ARCH_P1024 |
| bool |
| select FSL_LAW |
| select SYS_FSL_ERRATUM_A004508 |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_ELBC_A001 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select FSL_PCIE_DISABLE_ASPM |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_RMU |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_2 |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| select FSL_ELBC |
| imply CMD_EEPROM |
| imply CMD_NAND |
| imply CMD_SATA |
| imply CMD_PCI |
| imply CMD_REGINFO |
| imply SATA_SIL |
| |
| config ARCH_P1025 |
| bool |
| select FSL_LAW |
| select SYS_FSL_ERRATUM_A004508 |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_ELBC_A001 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select FSL_PCIE_DISABLE_ASPM |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_2 |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| select FSL_ELBC |
| imply CMD_SATA |
| imply CMD_REGINFO |
| |
| config ARCH_P2020 |
| bool |
| select BTB |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_5 |
| select SYS_FSL_ERRATUM_A004477 |
| select SYS_FSL_ERRATUM_A004508 |
| select SYS_FSL_ERRATUM_A005125 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_ERRATUM_ESDHC_A001 |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_2 |
| select SYS_PPC_E500_USE_DEBUG_TLB |
| select FSL_ELBC |
| imply CMD_EEPROM |
| imply CMD_NAND |
| imply CMD_REGINFO |
| imply TIMESTAMP |
| |
| config ARCH_P2041 |
| bool |
| select BACKSIDE_L2_CACHE |
| select E500MC |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_6 |
| select SYS_DPAA_FMAN |
| select SYS_DPAA_PME |
| select SYS_DPAA_RMAN |
| select SYS_FSL_ERRATUM_A004510 |
| select SYS_FSL_ERRATUM_A004849 |
| select SYS_FSL_ERRATUM_A005275 |
| select SYS_FSL_ERRATUM_A006261 |
| select SYS_FSL_ERRATUM_CPU_A003999 |
| select SYS_FSL_ERRATUM_DDR_A003 |
| select SYS_FSL_ERRATUM_DDR_A003474 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_ERRATUM_I2C_A004447 |
| select SYS_FSL_ERRATUM_NMG_CPU_A011 |
| select SYS_FSL_ERRATUM_SRIO_A004034 |
| select SYS_FSL_ERRATUM_USB14 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_QORIQ_CHASSIS1 |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v22 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_USB1_PHY_ENABLE |
| select SYS_FSL_USB2_PHY_ENABLE |
| select FSL_ELBC |
| imply CMD_NAND |
| |
| config ARCH_P3041 |
| bool |
| select BACKSIDE_L2_CACHE |
| select E500MC |
| select FSL_CORENET |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_6 |
| select SYS_FSL_DDR_VER_44 |
| select SYS_FSL_ERRATUM_A004510 |
| select SYS_FSL_ERRATUM_A004849 |
| select SYS_FSL_ERRATUM_A005275 |
| select SYS_FSL_ERRATUM_A005812 |
| select SYS_FSL_ERRATUM_A006261 |
| select SYS_FSL_ERRATUM_CPU_A003999 |
| select SYS_FSL_ERRATUM_DDR_A003 |
| select SYS_FSL_ERRATUM_DDR_A003474 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_ERRATUM_I2C_A004447 |
| select SYS_FSL_ERRATUM_NMG_CPU_A011 |
| select SYS_FSL_ERRATUM_SRIO_A004034 |
| select SYS_FSL_ERRATUM_USB14 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_QORIQ_CHASSIS1 |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v22 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_USB1_PHY_ENABLE |
| select SYS_FSL_USB2_PHY_ENABLE |
| select FSL_ELBC |
| imply CMD_NAND |
| imply CMD_SATA |
| imply CMD_REGINFO |
| imply FSL_SATA |
| |
| config ARCH_P4080 |
| bool |
| select BACKSIDE_L2_CACHE |
| select E500MC |
| select FSL_CORENET |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_6 |
| select SYS_FSL_DDR_VER_44 |
| select SYS_FSL_ERRATUM_A004510 |
| select SYS_FSL_ERRATUM_A004580 |
| select SYS_FSL_ERRATUM_A004849 |
| select SYS_FSL_ERRATUM_A005812 |
| select SYS_FSL_ERRATUM_A007075 |
| select SYS_FSL_ERRATUM_CPC_A002 |
| select SYS_FSL_ERRATUM_CPC_A003 |
| select SYS_FSL_ERRATUM_CPU_A003999 |
| select SYS_FSL_ERRATUM_DDR_A003 |
| select SYS_FSL_ERRATUM_DDR_A003474 |
| select SYS_FSL_ERRATUM_ELBC_A001 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_ERRATUM_ESDHC13 |
| select SYS_FSL_ERRATUM_ESDHC135 |
| select SYS_FSL_ERRATUM_I2C_A004447 |
| select SYS_FSL_ERRATUM_NMG_CPU_A011 |
| select SYS_FSL_ERRATUM_SRIO_A004034 |
| select SYS_FSL_PCIE_COMPAT_P4080_PCIE |
| select SYS_P4080_ERRATUM_CPU22 |
| select SYS_P4080_ERRATUM_PCIE_A003 |
| select SYS_P4080_ERRATUM_SERDES8 |
| select SYS_P4080_ERRATUM_SERDES9 |
| select SYS_P4080_ERRATUM_SERDES_A001 |
| select SYS_P4080_ERRATUM_SERDES_A005 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_QORIQ_CHASSIS1 |
| select SYS_FSL_RMU |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select FSL_ELBC |
| imply CMD_SATA |
| imply CMD_REGINFO |
| imply SATA_SIL |
| |
| config ARCH_P5040 |
| bool |
| select BACKSIDE_L2_CACHE |
| select E500MC |
| select FSL_CORENET |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_6 |
| select SYS_FSL_DDR_VER_44 |
| select SYS_FSL_ERRATUM_A004510 |
| select SYS_FSL_ERRATUM_A004699 |
| select SYS_FSL_ERRATUM_A005275 |
| select SYS_FSL_ERRATUM_A005812 |
| select SYS_FSL_ERRATUM_A006261 |
| select SYS_FSL_ERRATUM_DDR_A003 |
| select SYS_FSL_ERRATUM_DDR_A003474 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_ERRATUM_USB14 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_QORIQ_CHASSIS1 |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v24 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_USB1_PHY_ENABLE |
| select SYS_FSL_USB2_PHY_ENABLE |
| select SYS_PPC64 |
| select FSL_ELBC |
| imply CMD_SATA |
| imply CMD_REGINFO |
| imply FSL_SATA |
| |
| config ARCH_QEMU_E500 |
| bool |
| select SYS_CACHE_SHIFT_5 |
| |
| config ARCH_T1024 |
| bool |
| select BACKSIDE_L2_CACHE |
| select E500MC |
| select E5500 |
| select FSL_CORENET |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_6 |
| select SYS_DPAA_FMAN |
| select SYS_FSL_DDR_VER_50 |
| select SYS_FSL_ERRATUM_A008378 |
| select SYS_FSL_ERRATUM_A008109 |
| select SYS_FSL_ERRATUM_A009663 |
| select SYS_FSL_ERRATUM_A009942 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_DDR4 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_QORIQ_CHASSIS2 |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v24 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_5 |
| select SYS_FSL_SINGLE_SOURCE_CLK |
| select SYS_FSL_QMAN_V3 if SYS_DPAA_QBMAN |
| select SYS_FSL_USB_DUAL_PHY_ENABLE |
| select FSL_IFC |
| imply CMD_EEPROM |
| imply CMD_NAND |
| imply CMD_MTDPARTS |
| imply CMD_REGINFO |
| |
| config ARCH_T1040 |
| bool |
| select BACKSIDE_L2_CACHE |
| select E500MC |
| select E5500 |
| select FSL_CORENET |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_6 |
| select SYS_DPAA_FMAN |
| select SYS_DPAA_PME |
| select SYS_FSL_DDR_VER_50 |
| select SYS_FSL_ERRATUM_A008044 |
| select SYS_FSL_ERRATUM_A008378 |
| select SYS_FSL_ERRATUM_A008109 |
| select SYS_FSL_ERRATUM_A009663 |
| select SYS_FSL_ERRATUM_A009942 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_DDR4 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_QORIQ_CHASSIS2 |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v24 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_5 |
| select SYS_FSL_SINGLE_SOURCE_CLK |
| select SYS_FSL_QMAN_V3 if SYS_DPAA_QBMAN |
| select SYS_FSL_USB_DUAL_PHY_ENABLE |
| select FSL_IFC |
| imply CMD_MTDPARTS |
| imply CMD_NAND |
| imply CMD_REGINFO |
| |
| config ARCH_T1042 |
| bool |
| select BACKSIDE_L2_CACHE |
| select E500MC |
| select E5500 |
| select FSL_CORENET |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_6 |
| select SYS_DPAA_FMAN |
| select SYS_DPAA_PME |
| select SYS_FSL_DDR_VER_50 |
| select SYS_FSL_ERRATUM_A008044 |
| select SYS_FSL_ERRATUM_A008378 |
| select SYS_FSL_ERRATUM_A008109 |
| select SYS_FSL_ERRATUM_A009663 |
| select SYS_FSL_ERRATUM_A009942 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_DDR4 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_QORIQ_CHASSIS2 |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v24 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_5 |
| select SYS_FSL_SINGLE_SOURCE_CLK |
| select SYS_FSL_QMAN_V3 if SYS_DPAA_QBMAN |
| select SYS_FSL_USB_DUAL_PHY_ENABLE |
| select FSL_IFC |
| imply CMD_MTDPARTS |
| imply CMD_NAND |
| imply CMD_REGINFO |
| |
| config ARCH_T2080 |
| bool |
| select E500MC |
| select E6500 |
| select FSL_CORENET |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_6 |
| select SYS_DPAA_DCE if !NOBQFMAN |
| select SYS_DPAA_FMAN if !NOBQFMAN |
| select SYS_DPAA_PME if !NOBQFMAN |
| select SYS_DPAA_RMAN if !NOBQFMAN |
| select SYS_FSL_DDR_VER_47 |
| select SYS_FSL_ERRATUM_A006379 |
| select SYS_FSL_ERRATUM_A006593 |
| select SYS_FSL_ERRATUM_A007186 if CHAIN_OF_TRUST |
| select SYS_FSL_ERRATUM_A007212 |
| select SYS_FSL_ERRATUM_A007815 |
| select SYS_FSL_ERRATUM_A007907 |
| select SYS_FSL_ERRATUM_A008109 |
| select SYS_FSL_ERRATUM_A009942 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select FSL_PCIE_RESET |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_QORIQ_CHASSIS2 |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v30 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_SRIO_LIODN |
| select SYS_FSL_QMAN_V3 if SYS_DPAA_QBMAN |
| select SYS_FSL_USB_DUAL_PHY_ENABLE |
| select SYS_PMAN if !NOBQFMAN |
| select SYS_PPC64 |
| select FSL_IFC |
| imply CMD_SATA |
| imply CMD_NAND |
| imply CMD_REGINFO |
| imply FSL_SATA |
| imply ID_EEPROM |
| |
| config ARCH_T4240 |
| bool |
| select E500MC |
| select E6500 |
| select FSL_CORENET |
| select FSL_LAW |
| select SYS_CACHE_SHIFT_6 |
| select SYS_DPAA_DCE if !NOBQFMAN |
| select SYS_DPAA_FMAN if !NOBQFMAN |
| select SYS_DPAA_PME if !NOBQFMAN |
| select SYS_DPAA_RMAN if !NOBQFMAN |
| select SYS_FSL_DDR_VER_47 |
| select SYS_FSL_ERRATUM_A004468 |
| select SYS_FSL_ERRATUM_A005871 |
| select SYS_FSL_ERRATUM_A006261 |
| select SYS_FSL_ERRATUM_A006379 |
| select SYS_FSL_ERRATUM_A006593 |
| select SYS_FSL_ERRATUM_A007186 if CHAIN_OF_TRUST |
| select SYS_FSL_ERRATUM_A007798 |
| select SYS_FSL_ERRATUM_A007815 |
| select SYS_FSL_ERRATUM_A007907 |
| select SYS_FSL_ERRATUM_A008109 |
| select SYS_FSL_ERRATUM_A009942 |
| select SYS_FSL_HAS_DDR3 |
| select SYS_FSL_HAS_SEC |
| select SYS_FSL_QORIQ_CHASSIS2 |
| select SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v30 |
| select SYS_FSL_SEC_BE |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_SRIO_LIODN |
| select SYS_FSL_QMAN_V3 if SYS_DPAA_QBMAN |
| select SYS_FSL_USB_DUAL_PHY_ENABLE |
| select SYS_PMAN if !NOBQFMAN |
| select SYS_PPC64 |
| select FSL_IFC |
| imply CMD_SATA |
| imply CMD_NAND |
| imply CMD_REGINFO |
| imply FSL_SATA |
| |
| config MPC85XX_HAVE_RESET_VECTOR |
| bool "Indicate reset vector at CONFIG_RESET_VECTOR_ADDRESS - 0xffc" |
| depends on MPC85xx |
| |
| config BTB |
| bool "toggle branch predition" |
| |
| config BOOKE |
| bool |
| default y |
| |
| config E500 |
| bool |
| default y |
| help |
| Enable PowerPC E500 cores, including e500v1, e500v2, e500mc |
| |
| config E500MC |
| bool |
| select BTB |
| imply CMD_PCI |
| help |
| Enble PowerPC E500MC core |
| |
| config E5500 |
| bool |
| |
| config E6500 |
| bool |
| select BTB |
| help |
| Enable PowerPC E6500 core |
| |
| config NOBQFMAN |
| bool |
| |
| config FSL_LAW |
| bool |
| help |
| Use Freescale common code for Local Access Window |
| |
| config HETROGENOUS_CLUSTERS |
| bool |
| |
| config MAX_CPUS |
| int "Maximum number of CPUs permitted for MPC85xx" |
| default 12 if ARCH_T4240 |
| default 8 if ARCH_P4080 |
| default 4 if ARCH_B4860 || \ |
| ARCH_P2041 || \ |
| ARCH_P3041 || \ |
| ARCH_P5040 || \ |
| ARCH_T1040 || \ |
| ARCH_T1042 || \ |
| ARCH_T2080 |
| default 2 if ARCH_B4420 || \ |
| ARCH_BSC9132 || \ |
| ARCH_P1020 || \ |
| ARCH_P1021 || \ |
| ARCH_P1023 || \ |
| ARCH_P1024 || \ |
| ARCH_P1025 || \ |
| ARCH_P2020 || \ |
| ARCH_T1024 |
| default 1 |
| help |
| Set this number to the maximum number of possible CPUs in the SoC. |
| SoCs may have multiple clusters with each cluster may have multiple |
| ports. If some ports are reserved but higher ports are used for |
| cores, count the reserved ports. This will allocate enough memory |
| in spin table to properly handle all cores. |
| |
| config SYS_CCSRBAR_DEFAULT |
| hex "Default CCSRBAR address" |
| default 0xff700000 if ARCH_BSC9131 || \ |
| ARCH_BSC9132 || \ |
| ARCH_C29X || \ |
| ARCH_MPC8536 || \ |
| ARCH_MPC8540 || \ |
| ARCH_MPC8544 || \ |
| ARCH_MPC8548 || \ |
| ARCH_MPC8560 || \ |
| ARCH_P1010 || \ |
| ARCH_P1011 || \ |
| ARCH_P1020 || \ |
| ARCH_P1021 || \ |
| ARCH_P1024 || \ |
| ARCH_P1025 || \ |
| ARCH_P2020 |
| default 0xff600000 if ARCH_P1023 |
| default 0xfe000000 if ARCH_B4420 || \ |
| ARCH_B4860 || \ |
| ARCH_P2041 || \ |
| ARCH_P3041 || \ |
| ARCH_P4080 || \ |
| ARCH_P5040 || \ |
| ARCH_T1024 || \ |
| ARCH_T1040 || \ |
| ARCH_T1042 || \ |
| ARCH_T2080 || \ |
| ARCH_T4240 |
| default 0xe0000000 if ARCH_QEMU_E500 |
| help |
| Default value of CCSRBAR comes from power-on-reset. It |
| is fixed on each SoC. Some SoCs can have different value |
| if changed by pre-boot regime. The value here must match |
| the current value in SoC. If not sure, do not change. |
| |
| config SYS_DPAA_PME |
| bool |
| |
| config SYS_DPAA_DCE |
| bool |
| |
| config SYS_DPAA_RMAN |
| bool |
| |
| config A003399_NOR_WORKAROUND |
| bool |
| help |
| Enables a workaround for IFC erratum A003399. It is only required |
| during NOR boot. |
| |
| config A008044_WORKAROUND |
| bool |
| help |
| Enables a workaround for T1040/T1042 erratum A008044. It is only |
| required during NAND boot and valid for Rev 1.0 SoC revision |
| |
| config SYS_FSL_ERRATUM_A004468 |
| bool |
| |
| config SYS_FSL_ERRATUM_A004477 |
| bool |
| |
| config SYS_FSL_ERRATUM_A004508 |
| bool |
| |
| config SYS_FSL_ERRATUM_A004580 |
| bool |
| |
| config SYS_FSL_ERRATUM_A004699 |
| bool |
| |
| config SYS_FSL_ERRATUM_A004849 |
| bool |
| |
| config SYS_FSL_ERRATUM_A004510 |
| bool |
| |
| config SYS_FSL_ERRATUM_A004510_SVR_REV |
| hex |
| depends on SYS_FSL_ERRATUM_A004510 |
| default 0x20 if ARCH_P4080 |
| default 0x10 |
| |
| config SYS_FSL_ERRATUM_A004510_SVR_REV2 |
| hex |
| depends on (SYS_FSL_ERRATUM_A004510 && (ARCH_P2041 || ARCH_P3041)) |
| default 0x11 |
| |
| config SYS_FSL_ERRATUM_A005125 |
| bool |
| |
| config SYS_FSL_ERRATUM_A005434 |
| bool |
| |
| config SYS_FSL_ERRATUM_A005812 |
| bool |
| |
| config SYS_FSL_ERRATUM_A005871 |
| bool |
| |
| config SYS_FSL_ERRATUM_A005275 |
| bool |
| |
| config SYS_FSL_ERRATUM_A006261 |
| bool |
| |
| config SYS_FSL_ERRATUM_A006379 |
| bool |
| |
| config SYS_FSL_ERRATUM_A006384 |
| bool |
| |
| config SYS_FSL_ERRATUM_A006475 |
| bool |
| |
| config SYS_FSL_ERRATUM_A006593 |
| bool |
| |
| config SYS_FSL_ERRATUM_A007075 |
| bool |
| |
| config SYS_FSL_ERRATUM_A007186 |
| bool |
| |
| config SYS_FSL_ERRATUM_A007212 |
| bool |
| |
| config SYS_FSL_ERRATUM_A007815 |
| bool |
| |
| config SYS_FSL_ERRATUM_A007798 |
| bool |
| |
| config SYS_FSL_ERRATUM_A007907 |
| bool |
| |
| config SYS_FSL_ERRATUM_A008044 |
| bool |
| select A008044_WORKAROUND if MTD_RAW_NAND |
| |
| config SYS_FSL_ERRATUM_CPC_A002 |
| bool |
| |
| config SYS_FSL_ERRATUM_CPC_A003 |
| bool |
| |
| config SYS_FSL_ERRATUM_CPU_A003999 |
| bool |
| |
| config SYS_FSL_ERRATUM_ELBC_A001 |
| bool |
| |
| config SYS_FSL_ERRATUM_I2C_A004447 |
| bool |
| |
| config SYS_FSL_A004447_SVR_REV |
| hex |
| depends on SYS_FSL_ERRATUM_I2C_A004447 |
| default 0x00 if ARCH_MPC8548 |
| default 0x10 if ARCH_P1010 |
| default 0x11 if ARCH_P1023 || ARCH_P2041 || ARCH_BSC9132 |
| default 0x20 if ARCH_P3041 || ARCH_P4080 |
| |
| config SYS_FSL_ERRATUM_IFC_A002769 |
| bool |
| |
| config SYS_FSL_ERRATUM_IFC_A003399 |
| bool |
| |
| config SYS_FSL_ERRATUM_NMG_CPU_A011 |
| bool |
| |
| config SYS_FSL_ERRATUM_NMG_ETSEC129 |
| bool |
| |
| config SYS_FSL_ERRATUM_NMG_LBC103 |
| bool |
| |
| config SYS_FSL_ERRATUM_P1010_A003549 |
| bool |
| |
| config SYS_FSL_ERRATUM_SATA_A001 |
| bool |
| |
| config SYS_FSL_ERRATUM_SEC_A003571 |
| bool |
| |
| config SYS_FSL_ERRATUM_SRIO_A004034 |
| bool |
| |
| config SYS_FSL_ERRATUM_USB14 |
| bool |
| |
| config SYS_HAS_SERDES |
| bool |
| |
| config SYS_P4080_ERRATUM_CPU22 |
| bool |
| |
| config SYS_P4080_ERRATUM_PCIE_A003 |
| bool |
| |
| config SYS_P4080_ERRATUM_SERDES8 |
| bool |
| |
| config SYS_P4080_ERRATUM_SERDES9 |
| bool |
| |
| config SYS_P4080_ERRATUM_SERDES_A001 |
| bool |
| |
| config SYS_P4080_ERRATUM_SERDES_A005 |
| bool |
| |
| config FSL_PCIE_DISABLE_ASPM |
| bool |
| |
| config FSL_PCIE_RESET |
| bool |
| |
| config SYS_PMAN |
| bool |
| |
| config SYS_FSL_RAID_ENGINE |
| bool |
| |
| config SYS_FSL_RMU |
| bool |
| |
| config SYS_FSL_QORIQ_CHASSIS1 |
| bool |
| |
| config SYS_FSL_QORIQ_CHASSIS2 |
| bool |
| |
| config SYS_FSL_NUM_LAWS |
| int "Number of local access windows" |
| depends on FSL_LAW |
| default 32 if ARCH_B4420 || \ |
| ARCH_B4860 || \ |
| ARCH_P2041 || \ |
| ARCH_P3041 || \ |
| ARCH_P4080 || \ |
| ARCH_P5040 || \ |
| ARCH_T2080 || \ |
| ARCH_T4240 |
| default 16 if ARCH_T1024 || \ |
| ARCH_T1040 || \ |
| ARCH_T1042 |
| default 12 if ARCH_BSC9131 || \ |
| ARCH_BSC9132 || \ |
| ARCH_C29X || \ |
| ARCH_MPC8536 || \ |
| ARCH_P1010 || \ |
| ARCH_P1011 || \ |
| ARCH_P1020 || \ |
| ARCH_P1021 || \ |
| ARCH_P1023 || \ |
| ARCH_P1024 || \ |
| ARCH_P1025 || \ |
| ARCH_P2020 |
| default 10 if ARCH_MPC8544 || \ |
| ARCH_MPC8548 |
| default 8 if ARCH_MPC8540 || \ |
| ARCH_MPC8560 |
| help |
| Number of local access windows. This is fixed per SoC. |
| If not sure, do not change. |
| |
| config SYS_FSL_CORES_PER_CLUSTER |
| int |
| depends on SYS_FSL_QORIQ_CHASSIS2 |
| default 4 if ARCH_B4860 || ARCH_T2080 || ARCH_T4240 |
| default 2 if ARCH_B4420 |
| default 1 if ARCH_T1024 || ARCH_T1040 || ARCH_T1042 |
| |
| config SYS_FSL_THREADS_PER_CORE |
| int |
| depends on SYS_FSL_QORIQ_CHASSIS2 |
| default 2 if E6500 |
| default 1 |
| |
| config SYS_NUM_TLBCAMS |
| int "Number of TLB CAM entries" |
| default 64 if E500MC |
| default 16 |
| help |
| Number of TLB CAM entries for Book-E chips. 64 for E500MC, |
| 16 for other E500 SoCs. |
| |
| if HETROGENOUS_CLUSTERS |
| |
| config SYS_MAPLE |
| def_bool y |
| |
| config SYS_CPRI |
| def_bool y |
| |
| config PPC_CLUSTER_START |
| int |
| default 0 |
| |
| config DSP_CLUSTER_START |
| int |
| default 1 |
| |
| config SYS_CPRI_CLK |
| int |
| default 3 |
| |
| config SYS_ULB_CLK |
| int |
| default 4 |
| |
| config SYS_ETVPE_CLK |
| int |
| default 1 |
| |
| config MAX_DSP_CPUS |
| int |
| default 12 if ARCH_B4860 |
| default 2 if ARCH_B4420 |
| endif |
| |
| config SYS_L2_SIZE_256KB |
| bool |
| |
| config SYS_L2_SIZE_512KB |
| bool |
| |
| config SYS_L2_SIZE |
| int |
| default 262144 if SYS_L2_SIZE_256KB |
| default 524288 if SYS_L2_SIZE_512KB |
| |
| config BACKSIDE_L2_CACHE |
| bool |
| |
| config SYS_L3_SIZE_256KB |
| bool |
| |
| config SYS_L3_SIZE_512KB |
| bool |
| |
| config SYS_L3_SIZE_1024KB |
| bool |
| |
| config SYS_L3_SIZE |
| int |
| default 262144 if SYS_L3_SIZE_256KB |
| default 524288 if SYS_L3_SIZE_512KB |
| default 1048576 if SYS_L3_SIZE_512KB |
| |
| config SYS_PPC64 |
| bool |
| |
| config SYS_PPC_E500_USE_DEBUG_TLB |
| bool |
| |
| config FSL_ELBC |
| bool |
| |
| config SYS_PPC_E500_DEBUG_TLB |
| int "Temporary TLB entry for external debugger" |
| depends on SYS_PPC_E500_USE_DEBUG_TLB |
| default 0 if ARCH_MPC8544 || ARCH_MPC8548 |
| default 1 if ARCH_MPC8536 |
| default 2 if ARCH_P1011 || \ |
| ARCH_P1020 || \ |
| ARCH_P1021 || \ |
| ARCH_P1024 || \ |
| ARCH_P1025 || \ |
| ARCH_P2020 |
| default 3 if ARCH_P1010 || \ |
| ARCH_BSC9132 || \ |
| ARCH_C29X |
| help |
| Select a temporary TLB entry to be used during boot to work |
| around limitations in e500v1 and e500v2 external debugger |
| support. This reduces the portions of the boot code where |
| breakpoints and single stepping do not work. The value of this |
| symbol should be set to the TLB1 entry to be used for this |
| purpose. If unsure, do not change. |
| |
| config SYS_FSL_IFC_CLK_DIV |
| int "Divider of platform clock" |
| depends on FSL_IFC |
| default 2 if ARCH_B4420 || \ |
| ARCH_B4860 || \ |
| ARCH_T1024 || \ |
| ARCH_T1040 || \ |
| ARCH_T1042 || \ |
| ARCH_T4240 |
| default 1 |
| help |
| Defines divider of platform clock(clock input to |
| IFC controller). |
| |
| config SYS_FSL_LBC_CLK_DIV |
| int "Divider of platform clock" |
| depends on FSL_ELBC || ARCH_MPC8540 || \ |
| ARCH_MPC8548 || \ |
| ARCH_MPC8560 |
| |
| default 2 if ARCH_P2041 || \ |
| ARCH_P3041 || \ |
| ARCH_P4080 || \ |
| ARCH_P5040 |
| default 1 |
| |
| help |
| Defines divider of platform clock(clock input to |
| eLBC controller). |
| |
| config ENABLE_36BIT_PHYS |
| bool "Enable 36bit physical address space support" |
| |
| config SYS_BOOK3E_HV |
| bool "Category E.HV is supported" |
| depends on BOOKE |
| |
| config FSL_CORENET |
| bool |
| select SYS_FSL_CPC |
| |
| config FSL_NGPIXIS |
| bool |
| |
| config SYS_CPC_REINIT_F |
| bool |
| help |
| The CPC is configured as SRAM at the time of U-Boot entry and is |
| required to be re-initialized. |
| |
| config SYS_FSL_CPC |
| bool |
| |
| config SYS_CACHE_STASHING |
| bool "Enable cache stashing" |
| |
| config SYS_FSL_PCIE_COMPAT_P4080_PCIE |
| bool |
| |
| config SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v22 |
| bool |
| |
| config SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v24 |
| bool |
| |
| config SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v30 |
| bool |
| |
| config SYS_FSL_PCIE_COMPAT |
| string |
| depends on FSL_CORENET |
| default "fsl,p4080-pcie" if SYS_FSL_PCIE_COMPAT_P4080_PCIE |
| default "fsl,qoriq-pcie-v2.2" if SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v22 |
| default "fsl,qoriq-pcie-v2.4" if SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v24 |
| default "fsl,qoriq-pcie-v3.0" if SYS_FSL_PCIE_COMPAT_QORIQ_PCIE_v30 |
| help |
| Defines the string to utilize when trying to match PCIe device tree |
| nodes for the given platform. |
| |
| config SYS_FSL_SINGLE_SOURCE_CLK |
| bool |
| |
| config SYS_FSL_SRIO_LIODN |
| bool |
| |
| config SYS_FSL_TBCLK_DIV |
| int |
| default 32 if ARCH_P2041 || ARCH_P3041 |
| default 16 if ARCH_P4080 || ARCH_P5040 || ARCH_T4240 || ARCH_B4860 || \ |
| ARCH_B4420 || ARCH_T1040 || ARCH_T1042 || \ |
| ARCH_T1024 || ARCH_T2080 |
| default 8 |
| help |
| Defines the core time base clock divider ratio compared to the system |
| clock. On most PQ3 devices this is 8, on newer QorIQ devices it can |
| be 16 or 32. The ratio varies from SoC to Soc. |
| |
| config SYS_FSL_USB1_PHY_ENABLE |
| bool |
| |
| config SYS_FSL_USB2_PHY_ENABLE |
| bool |
| |
| config SYS_FSL_USB_DUAL_PHY_ENABLE |
| bool |
| |
| config SYS_MPC85XX_NO_RESETVEC |
| bool "Discard resetvec section and move bootpg section up" |
| depends on MPC85xx |
| help |
| If this variable is specified, the section .resetvec is not kept and |
| the section .bootpg is placed in the previous 4k of the .text section. |
| |
| config SPL_SYS_MPC85XX_NO_RESETVEC |
| bool "Discard resetvec section and move bootpg section up, in SPL" |
| depends on MPC85xx && SPL |
| help |
| If this variable is specified, the section .resetvec is not kept and |
| the section .bootpg is placed in the previous 4k of the .text section, |
| of the SPL portion of the binary. |
| |
| config TPL_SYS_MPC85XX_NO_RESETVEC |
| bool "Discard resetvec section and move bootpg section up, in TPL" |
| depends on MPC85xx && TPL |
| help |
| If this variable is specified, the section .resetvec is not kept and |
| the section .bootpg is placed in the previous 4k of the .text section, |
| of the SPL portion of the binary. |
| |
| config FSL_VIA |
| bool |
| |
| source "board/emulation/qemu-ppce500/Kconfig" |
| source "board/freescale/mpc8548cds/Kconfig" |
| source "board/freescale/p1010rdb/Kconfig" |
| source "board/freescale/p1_p2_rdb_pc/Kconfig" |
| source "board/freescale/p2041rdb/Kconfig" |
| source "board/freescale/t102xrdb/Kconfig" |
| source "board/freescale/t104xrdb/Kconfig" |
| source "board/freescale/t208xqds/Kconfig" |
| source "board/freescale/t208xrdb/Kconfig" |
| source "board/freescale/t4rdb/Kconfig" |
| source "board/socrates/Kconfig" |
| |
| endmenu |