blob: 3fc3bb844a62badb7f57972d01cd3e922b3512d9 [file] [log] [blame]
/*
* (C) Copyright 2001-2003
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_405EP 1 /* This is a PPC405 CPU */
#define CONFIG_PLU405 1 /* ...on a PLU405 board */
#define CONFIG_SYS_TEXT_BASE 0xFFF80000
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */
#define CONFIG_SYS_CLK_FREQ 33333400 /* external frequency to pll */
#undef CONFIG_BOOTARGS
#undef CONFIG_BOOTCOMMAND
#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#undef CONFIG_HAS_ETH1
#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
#define CONFIG_RESET_PHY_R 1 /* use reset_phy() */
#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#define CONFIG_CMD_PCI
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_IDE
#define CONFIG_CMD_NAND
#define CONFIG_CMD_DATE
#define CONFIG_CMD_EEPROM
#define CONFIG_SUPPORT_VFAT
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_RTC_MC146818 /* DS1685 is MC146818 compatible*/
#define CONFIG_SYS_RTC_REG_BASE_ADDR 0xF0000500 /* RTC Base Address */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
#define CONFIG_SYS_BASE_BAUD 691200
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_SYS_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
/*
* NAND-FLASH stuff
*/
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define NAND_BIG_DELAY_US 25
#define CONFIG_SYS_NAND_CE (0x80000000 >> 1) /* our CE is GPIO1 */
#define CONFIG_SYS_NAND_RDY (0x80000000 >> 4) /* our RDY is GPIO4 */
#define CONFIG_SYS_NAND_CLE (0x80000000 >> 2) /* our CLE is GPIO2 */
#define CONFIG_SYS_NAND_ALE (0x80000000 >> 3) /* our ALE is GPIO3 */
#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1 /* ".i" read skips bad blocks */
#define CONFIG_SYS_NAND_QUIET 1
/*
* PCI stuff
*/
#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
#define PCI_HOST_FORCE 1 /* configure as pci host */
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_PCI_HOST PCI_HOST_FORCE /* select pci host function */
/* resource configuration */
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
#define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
#define CONFIG_SYS_PCI_PTM1MS 0xf8000001 /* 128MB, enable hard-wired to 1 */
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
#define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
#define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
#define CONFIG_SYS_PCI_PTM2PCI 0x08000000 /* Host: use this pci address */
/*
* IDE/ATA stuff
*/
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET 1 /* reset for ide supported */
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
/* max. 1 drives per IDE bus */
#define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1)
#define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
#define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
#define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register access */
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* FLASH organization
*/
#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 1000 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st addr for flash config cycles */
#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd addr for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector */
/*
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN (~(CONFIG_SYS_TEXT_BASE) + 1)
#define CONFIG_SYS_MALLOC_LEN (1024 << 10)
/*
* Environment Variable setup
*/
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET 0x100 /* reseve 0x100 bytes for strapping */
#define CONFIG_ENV_SIZE 0x700
/*
* I2C EEPROM (24WC16) for environment
*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_PPC4XX
#define CONFIG_SYS_I2C_PPC4XX_CH0
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM 24WC16 */
#define CONFIG_SYS_EEPROM_WREN 1
/* 24WC16 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The 24WC16 has */
/* 16 byte page write mode using */
/* last 4 bits of the address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
/*
* External Bus Controller (EBC) Setup
*/
#define CAN0_BA 0xF0000000 /* CAN0 Base Address */
#define CAN1_BA 0xF0000100 /* CAN1 Base Address */
#define DUART0_BA 0xF0000400 /* DUART Base Address */
#define DUART1_BA 0xF0000408 /* DUART Base Address */
#define RTC_BA 0xF0000500 /* RTC Base Address */
#define VGA_BA 0xF1000000 /* Epson VGA Base Address */
#define CONFIG_SYS_NAND_BASE 0xF4000000 /* NAND FLASH Base Address */
/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
/* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
#define CONFIG_SYS_EBC_PB0AP 0x92015480
/* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000
/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
#define CONFIG_SYS_EBC_PB1AP 0x92015480
/* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
#define CONFIG_SYS_EBC_PB1CR 0xF4018000
/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB2AP 0x010053C0
/* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
#define CONFIG_SYS_EBC_PB2CR 0xF0018000
/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB3AP 0x010053C0
/* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
#define CONFIG_SYS_EBC_PB3CR 0xF011A000
/*
* FPGA stuff
*/
#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */
/* FPGA internal regs */
#define CONFIG_SYS_FPGA_CTRL 0x000
/* FPGA Control Reg */
#define CONFIG_SYS_FPGA_CTRL_CF_RESET 0x0001
#define CONFIG_SYS_FPGA_CTRL_WDI 0x0002
#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020
#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
#define CONFIG_SYS_FPGA_MAX_SIZE 128*1024 /* 128kByte is enough for XC2S50E*/
/* FPGA program pin configuration */
#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
#define CONFIG_SYS_FPGA_INIT 0x00010000 /* FPGA init pin (ppc input) */
#define CONFIG_SYS_FPGA_DONE 0x00008000 /* FPGA done pin (ppc input) */
/*
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
#define CONFIG_SYS_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* Definitions for GPIO setup (PPC405EP specific)
*
* GPIO0[0] - External Bus Controller BLAST output
* GPIO0[1-9] - Instruction trace outputs -> GPIO
* GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
* GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
* GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
* GPIO0[24-27] - UART0 control signal inputs/outputs
* GPIO0[28-29] - UART1 data signal input/output
* GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
*/
#define CONFIG_SYS_GPIO0_OSRL 0x00000550
#define CONFIG_SYS_GPIO0_OSRH 0x00000110
#define CONFIG_SYS_GPIO0_ISR1L 0x00000000
#define CONFIG_SYS_GPIO0_ISR1H 0x15555445
#define CONFIG_SYS_GPIO0_TSRL 0x00000000
#define CONFIG_SYS_GPIO0_TSRH 0x00000000
#define CONFIG_SYS_GPIO0_TCR 0x77FE0014
#define CONFIG_SYS_DUART_RST (0x80000000 >> 14)
#define CONFIG_SYS_EEPROM_WP (0x80000000 >> 0)
/*
* Default speed selection (cpu_plb_opb_ebc) in MHz.
* This value will be set if iic boot eprom is disabled.
*/
#if 1
#define PLLMR0_DEFAULT PLLMR0_266_133_66_33
#define PLLMR1_DEFAULT PLLMR1_266_133_66_33
#endif
#if 0
#define PLLMR0_DEFAULT PLLMR0_200_100_50_33
#define PLLMR1_DEFAULT PLLMR1_200_100_50_33
#endif
#if 0
#define PLLMR0_DEFAULT PLLMR0_133_66_66_33
#define PLLMR1_DEFAULT PLLMR1_133_66_66_33
#endif
/*
* PCI OHCI controller
*/
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_PCI_OHCI 1
#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
/*
* UBI
*/
#define CONFIG_RBTREE
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_LZO
#endif /* __CONFIG_H */