| /* |
| * (C) Copyright 2007 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * Configuation settings for the SMN42 board from Siemens. |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * If we are developing, we might want to start u-boot from ram |
| * so we MUST NOT initialize critical regs like mem-timing ... |
| */ |
| #undef CONFIG_SKIP_LOWLEVEL_INIT |
| #undef CONFIG_SKIP_RELOCATE_UBOOT |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| #define CONFIG_ARM7 1 /* This is a ARM7 CPU */ |
| #define CONFIG_ARM_THUMB 1 /* this is an ARM720TDMI */ |
| #define CONFIG_LPC2292 |
| #undef CONFIG_ARM7_REVD /* disable ARM720 REV.D Workarounds */ |
| |
| #undef CONFIG_USE_IRQ /* don't need them anymore */ |
| |
| /* |
| * Size of malloc() pool |
| */ |
| #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) |
| #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ |
| |
| /* |
| * Hardware drivers |
| */ |
| |
| /* |
| * select serial console configuration |
| */ |
| #define CONFIG_LPC2292_SERIAL |
| #define CONFIG_SERIAL1 1 /* we use Serial line 1 */ |
| |
| /* allow to overwrite serial and ethaddr */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| |
| |
| /* enable I2C and select the hardware/software driver */ |
| #undef CONFIG_HARD_I2C /* I2C with hardware support */ |
| #define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ |
| /* this would be 0xAE if E0, E1 and E2 were pulled high */ |
| #define CONFIG_SYS_I2C_SLAVE 0xA0 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR (0xA0 >> 1) |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16 bit address */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 bytes per write */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 |
| /* not used but required by devices.c */ |
| #define CONFIG_SYS_I2C_SPEED 10000 |
| |
| #ifdef CONFIG_SOFT_I2C |
| /* |
| * Software (bit-bang) I2C driver configuration |
| */ |
| #define SCL 0x00000004 /* P0.2 */ |
| #define SDA 0x00000008 /* P0.3 */ |
| |
| #define I2C_READ ((GET32(IO0PIN) & SDA) ? 1 : 0) |
| #define I2C_SDA(x) { if (x) PUT32(IO0SET, SDA); else PUT32(IO0CLR, SDA); } |
| #define I2C_SCL(x) { if (x) PUT32(IO0SET, SCL); else PUT32(IO0CLR, SCL); } |
| #define I2C_DELAY { udelay(100); } |
| #define I2C_ACTIVE { unsigned int i2ctmp; \ |
| i2ctmp = GET32(IO0DIR); \ |
| i2ctmp |= SDA; \ |
| PUT32(IO0DIR, i2ctmp); } |
| #define I2C_TRISTATE { unsigned int i2ctmp; \ |
| i2ctmp = GET32(IO0DIR); \ |
| i2ctmp &= ~SDA; \ |
| PUT32(IO0DIR, i2ctmp); } |
| #endif /* CONFIG_SOFT_I2C */ |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_FAT |
| #define CONFIG_CMD_MMC |
| #define CONFIG_CMD_NET |
| #define CONFIG_CMD_EEPROM |
| #define CONFIG_CMD_PING |
| |
| |
| #define CONFIG_DOS_PARTITION |
| |
| #define CONFIG_BOOTDELAY 5 |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "SMN42 # " /* Monitor Command Prompt */ |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x81800000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x83000000 /* 24 MB in SRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x81000000 /* default load address */ |
| /* for uClinux img is here*/ |
| |
| #define CONFIG_SYS_SYS_CLK_FREQ 58982400 /* Hz */ |
| #define CONFIG_SYS_HZ 2048 /* decrementer freq in Hz */ |
| |
| /* valid baudrates */ |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| |
| /*----------------------------------------------------------------------- |
| * Stack sizes |
| * |
| * The stack sizes are set up in start.S using the settings below |
| */ |
| #define CONFIG_STACKSIZE (128*1024) /* regular stack */ |
| #ifdef CONFIG_USE_IRQ |
| #define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ |
| #define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * Physical Memory Map |
| */ |
| #define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of SRAM */ |
| #define PHYS_SDRAM_1 0x81000000 /* SRAM Bank #1 */ |
| #define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB SRAM */ |
| |
| /* This is the external flash */ |
| #define PHYS_FLASH_1 0x80000000 /* Flash Bank #1 */ |
| #define PHYS_FLASH_SIZE 0x01000000 /* 16 MB */ |
| |
| /*----------------------------------------------------------------------- |
| * FLASH and environment organization |
| */ |
| |
| /* |
| * The first entry in CONFIG_SYS_FLASH_BANKS_LIST is a dummy, but it must be present. |
| */ |
| #define CONFIG_SYS_FLASH_BANKS_LIST { 0, PHYS_FLASH_1 } |
| #define CONFIG_SYS_FLASH_ADDR0 0x555 |
| #define CONFIG_SYS_FLASH_ADDR1 0x2AA |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 16384 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */ |
| |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ |
| |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| /* The Environment Sector is in the CPU-internal flash */ |
| #define CONFIG_SYS_FLASH_BASE 0 |
| #define CONFIG_ENV_OFFSET 0x3C000 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) |
| #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ |
| |
| #define CONFIG_CMDLINE_TAG |
| #define CONFIG_SETUP_MEMORY_TAGS |
| #define CONFIG_INITRD_TAG |
| #define CONFIG_MMC 1 |
| /* we use this ethernet chip */ |
| #define CONFIG_ENC28J60 |
| |
| #endif /* __CONFIG_H */ |