include/configs/vme8349.h - platform/external/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * esd vme8349 U-Boot configuration file
  * Copyright (c) 2008, 2009 esd gmbh Hannover Germany
  *
  * (C) Copyright 2006-2010
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * reinhard.arlt@esd-electronics.de
  * Based on the MPC8349EMDS config.
  */

 /*
  * vme8349 board configuration file.
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  */
 #define CONFIG_E300		1	/* E300 Family */

 /* Don't enable PCI2 on vme834x - it doesn't exist physically. */
 #undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */

 #undef CONFIG_SYS_DRAM_TEST			/* memory test, takes time */

 /*
  * DDR Setup
  */
 #define CONFIG_DDR_ECC			/* only for ECC DDR module */
 #define CONFIG_DDR_ECC_CMD		/* use DDR ECC user commands */
 #define CONFIG_SPD_EEPROM
 #define SPD_EEPROM_ADDRESS		0x54
 #define CONFIG_SYS_READ_SPD		vme8349_read_spd
 #define CONFIG_SYS_83XX_DDR_USES_CS0	/* esd; Fsl board uses CS2/CS3 */

 /*
  * 32-bit data path mode.
  *
  * Please note that using this mode for devices with the real density of 64-bit
  * effectively reduces the amount of available memory due to the effect of
  * wrapping around while translating address to row/columns, for example in the
  * 256MB module the upper 128MB get aliased with contents of the lower
  * 128MB); normally this define should be used for devices with real 32-bit
  * data path.
  */
 #undef CONFIG_DDR_32BIT

 #define CONFIG_SYS_SDRAM_BASE		0x00000000	/* DDR is sys memory*/
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
 					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
 #define CONFIG_DDR_2T_TIMING
 #define CONFIG_SYS_DDRCDR		(DDRCDR_DHC_EN \
 					| DDRCDR_ODT \
 					| DDRCDR_Q_DRN)
 					/* 0x80080001 */

 /*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_BASE		0xf8000000	/* start of FLASH   */
 #define CONFIG_SYS_FLASH_SIZE		128		/* flash size in MB */


 #define CONFIG_SYS_WINDOW1_BASE		0xf0000000


 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device*/

 #undef CONFIG_SYS_FLASH_CHECKSUM
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase TO (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write TO (ms) */

 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */

 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
 #else
 #undef CONFIG_SYS_RAMBOOT
 #endif

 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #define CONFIG_SYS_INIT_RAM_ADDR	0xF7000000	/* Initial RAM addr */
 #define CONFIG_SYS_INIT_RAM_SIZE		0x1000		/* size */

 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
 					 GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB */
 #define CONFIG_SYS_MALLOC_LEN		(256 * 1024)	/* Malloc size */

 #undef CONFIG_SYS_LB_SDRAM	/* if board has SDRAM on local bus */

 /*
  * Serial Port
  */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

 #define CONFIG_SYS_BAUDRATE_TABLE  \
 		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

 #define CONFIG_SYS_NS16550_COM1		(CONFIG_SYS_IMMR + 0x4500)
 #define CONFIG_SYS_NS16550_COM2		(CONFIG_SYS_IMMR + 0x4600)

 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_FSL_I2C2_SPEED	400000
 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
 /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */

 #define CONFIG_SYS_I2C_8574_ADDR2       0x20    /* I2C1, PCF8574 */

 /* TSEC */
 #define CONFIG_SYS_TSEC1_OFFSET	0x24000
 #define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 #define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)

 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
 #define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
 #define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
 #define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
 #define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
 #define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI1_IO_BASE		0x00000000
 #define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
 #define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */

 #define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
 #define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
 #define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
 #define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
 #define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI2_IO_BASE		0x00000000
 #define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
 #define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */

 #if defined(CONFIG_PCI)

 #undef CONFIG_TULIP

 #if !defined(CONFIG_PCI_PNP)
 	#define PCI_ENET0_IOADDR	0xFIXME
 	#define PCI_ENET0_MEMADDR	0xFIXME
 	#define PCI_IDSEL_NUMBER	0xFIXME
 #endif

 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 #define CONFIG_SYS_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */

 #endif	/* CONFIG_PCI */

 /*
  * TSEC configuration
  */

 #if defined(CONFIG_TSEC_ENET)

 #define CONFIG_GMII			/* MII PHY management */
 #define CONFIG_TSEC1
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2
 #define CONFIG_TSEC2_NAME	"TSEC1"
 #define CONFIG_PHY_M88E1111
 #define TSEC1_PHY_ADDR		0x08
 #define TSEC2_PHY_ADDR		0x10
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 #define TSEC1_FLAGS		TSEC_GIGABIT
 #define TSEC2_FLAGS		TSEC_GIGABIT

 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"

 #endif	/* CONFIG_TSEC_ENET */

 /*
  * Environment
  */
 #ifndef CONFIG_SYS_RAMBOOT
 /* Address and size of Redundant Environment Sector	*/
 #endif

 #define CONFIG_LOADS_ECHO		/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE

 #define CONFIG_SYS_RTC_BUS_NUM  0x01
 #define CONFIG_SYS_I2C_RTC_ADDR	0x32

 /* Pass Ethernet MAC to VxWorks */
 #define CONFIG_SYS_VXWORKS_MAC_PTR	0x000043f0

 #undef CONFIG_WATCHDOG			/* watchdog disabled */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 256 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20)	/* Init Memory map for Linux*/

 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */

 /* System IO Config */
 #define CONFIG_SYS_SICRH 0
 #define CONFIG_SYS_SICRL SICRL_LDP_A

 #define CONFIG_SYS_GPIO1_PRELIM
 #define CONFIG_SYS_GPIO1_DIR	0x00100000
 #define CONFIG_SYS_GPIO1_DAT	0x00100000

 #define CONFIG_SYS_GPIO2_PRELIM
 #define CONFIG_SYS_GPIO2_DIR	0x78900000
 #define CONFIG_SYS_GPIO2_DAT	0x70100000

 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #endif

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif

 /*
  * Environment Configuration
  */
 #define CONFIG_ENV_OVERWRITE

 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #endif

 #define CONFIG_HOSTNAME		"VME8349"
 #define CONFIG_ROOTPATH		"/tftpboot/rootfs"
 #define CONFIG_BOOTFILE		"uImage"

 #define CONFIG_LOADADDR		800000	/* def location for tftp and bootm */

 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"hostname=vme8349\0"						\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 	"flash_nfs=run nfsargs addip addtty;"				\
 		"bootm ${kernel_addr}\0"				\
 	"flash_self=run ramargs addip addtty;"				\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
 		"bootm\0"						\
 	"load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0"		\
 	"update=protect off fff00000 fff3ffff; "			\
 		"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
 	"upd=run load update\0"						\
 	"fdtaddr=780000\0"						\
 	"fdtfile=vme8349.dtb\0"						\
 	""

 #define CONFIG_NFSBOOTCOMMAND						\
 	"setenv bootargs root=/dev/nfs rw "				\
 		"nfsroot=$serverip:$rootpath "				\
 		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
 							"$netdev:off "	\
 		"console=$consoledev,$baudrate $othbootargs;"		\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr - $fdtaddr"

 #define CONFIG_RAMBOOTCOMMAND						\
 	"setenv bootargs root=/dev/ram rw "				\
 		"console=$consoledev,$baudrate $othbootargs;"		\
 	"tftp $ramdiskaddr $ramdiskfile;"				\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr $ramdiskaddr $fdtaddr"

 #define CONFIG_BOOTCOMMAND	"run flash_self"

 #ifndef __ASSEMBLY__
 int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
 		     unsigned char *buffer, int len);
 #endif

 #endif	/* __CONFIG_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* esd vme8349 U-Boot configuration file
	* Copyright (c) 2008, 2009 esd gmbh Hannover Germany
	*
	* (C) Copyright 2006-2010
	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	*
	* reinhard.arlt@esd-electronics.de
	* Based on the MPC8349EMDS config.
	*/

	/*
	* vme8349 board configuration file.
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_E300 1 /* E300 Family */

	/* Don't enable PCI2 on vme834x - it doesn't exist physically. */
	#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */

	#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */

	/*
	* DDR Setup
	*/
	#define CONFIG_DDR_ECC /* only for ECC DDR module */
	#define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
	#define CONFIG_SPD_EEPROM
	#define SPD_EEPROM_ADDRESS 0x54
	#define CONFIG_SYS_READ_SPD vme8349_read_spd
	#define CONFIG_SYS_83XX_DDR_USES_CS0 /* esd; Fsl board uses CS2/CS3 */

	/*
	* 32-bit data path mode.
	*
	* Please note that using this mode for devices with the real density of 64-bit
	* effectively reduces the amount of available memory due to the effect of
	* wrapping around while translating address to row/columns, for example in the
	* 256MB module the upper 128MB get aliased with contents of the lower
	* 128MB); normally this define should be used for devices with real 32-bit
	* data path.
	*/
	#undef CONFIG_DDR_32BIT

	#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is sys memory*/
	#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \
	\| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
	#define CONFIG_DDR_2T_TIMING
	#define CONFIG_SYS_DDRCDR (DDRCDR_DHC_EN \
	\| DDRCDR_ODT \
	\| DDRCDR_Q_DRN)
	/* 0x80080001 */

	/*
	* FLASH on the Local Bus
	*/
	#define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */
	#define CONFIG_SYS_FLASH_SIZE 128 /* flash size in MB */


	#define CONFIG_SYS_WINDOW1_BASE 0xf0000000


	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device*/

	#undef CONFIG_SYS_FLASH_CHECKSUM
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase TO (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO (ms) */

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */

	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	#define CONFIG_SYS_RAMBOOT
	#else
	#undef CONFIG_SYS_RAMBOOT
	#endif

	#define CONFIG_SYS_INIT_RAM_LOCK 1
	#define CONFIG_SYS_INIT_RAM_ADDR 0xF7000000 /* Initial RAM addr */
	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* size */

	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
	GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB */
	#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Malloc size */

	#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */

	/*
	* Serial Port
	*/
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
	#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
	/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */

	#define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */

	/* TSEC */
	#define CONFIG_SYS_TSEC1_OFFSET 0x24000
	#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
	#define CONFIG_SYS_TSEC2_OFFSET 0x25000
	#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)

	/*
	* General PCI
	* Addresses are mapped 1-1.
	*/
	#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
	#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
	#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
	#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
	#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
	#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
	#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */

	#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
	#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
	#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
	#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
	#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
	#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
	#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */

	#if defined(CONFIG_PCI)

	#undef CONFIG_TULIP

	#if !defined(CONFIG_PCI_PNP)
	#define PCI_ENET0_IOADDR 0xFIXME
	#define PCI_ENET0_MEMADDR 0xFIXME
	#define PCI_IDSEL_NUMBER 0xFIXME
	#endif

	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */

	#endif /* CONFIG_PCI */

	/*
	* TSEC configuration
	*/

	#if defined(CONFIG_TSEC_ENET)

	#define CONFIG_GMII /* MII PHY management */
	#define CONFIG_TSEC1
	#define CONFIG_TSEC1_NAME "TSEC0"
	#define CONFIG_TSEC2
	#define CONFIG_TSEC2_NAME "TSEC1"
	#define CONFIG_PHY_M88E1111
	#define TSEC1_PHY_ADDR 0x08
	#define TSEC2_PHY_ADDR 0x10
	#define TSEC1_PHYIDX 0
	#define TSEC2_PHYIDX 0
	#define TSEC1_FLAGS TSEC_GIGABIT
	#define TSEC2_FLAGS TSEC_GIGABIT

	/* Options are: TSEC[0-1] */
	#define CONFIG_ETHPRIME "TSEC0"

	#endif /* CONFIG_TSEC_ENET */

	/*
	* Environment
	*/
	#ifndef CONFIG_SYS_RAMBOOT
	/* Address and size of Redundant Environment Sector */
	#endif

	#define CONFIG_LOADS_ECHO /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE

	#define CONFIG_SYS_RTC_BUS_NUM 0x01
	#define CONFIG_SYS_I2C_RTC_ADDR 0x32

	/* Pass Ethernet MAC to VxWorks */
	#define CONFIG_SYS_VXWORKS_MAC_PTR 0x000043f0

	#undef CONFIG_WATCHDOG /* watchdog disabled */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 256 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Init Memory map for Linux*/

	#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */

	/* System IO Config */
	#define CONFIG_SYS_SICRH 0
	#define CONFIG_SYS_SICRL SICRL_LDP_A

	#define CONFIG_SYS_GPIO1_PRELIM
	#define CONFIG_SYS_GPIO1_DIR 0x00100000
	#define CONFIG_SYS_GPIO1_DAT 0x00100000

	#define CONFIG_SYS_GPIO2_PRELIM
	#define CONFIG_SYS_GPIO2_DIR 0x78900000
	#define CONFIG_SYS_GPIO2_DAT 0x70100000

	#ifdef CONFIG_PCI
	#define CONFIG_PCI_INDIRECT_BRIDGE
	#endif

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
	#endif

	/*
	* Environment Configuration
	*/
	#define CONFIG_ENV_OVERWRITE

	#if defined(CONFIG_TSEC_ENET)
	#define CONFIG_HAS_ETH0
	#define CONFIG_HAS_ETH1
	#endif

	#define CONFIG_HOSTNAME "VME8349"
	#define CONFIG_ROOTPATH "/tftpboot/rootfs"
	#define CONFIG_BOOTFILE "uImage"

	#define CONFIG_LOADADDR 800000 /* def location for tftp and bootm */

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"hostname=vme8349\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
	"flash_nfs=run nfsargs addip addtty;" \
	"bootm ${kernel_addr}\0" \
	"flash_self=run ramargs addip addtty;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
	"bootm\0" \
	"load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0" \
	"update=protect off fff00000 fff3ffff; " \
	"era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
	"upd=run load update\0" \
	"fdtaddr=780000\0" \
	"fdtfile=vme8349.dtb\0" \
	""

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
	"$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#define CONFIG_BOOTCOMMAND "run flash_self"

	#ifndef __ASSEMBLY__
	int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
	unsigned char *buffer, int len);
	#endif

	#endif /* __CONFIG_H */