include/configs/P1023RDB.h - platform/external/u-boot - Gitiles

 /*
  * Copyright 2013 Freescale Semiconductor, Inc.
  *
  * Authors:  Roy Zang <tie-fei.zang@freescale.com>
  *	     Chunhe Lan <Chunhe.Lan@freescale.com>
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xeff40000
 #endif

 #ifndef CONFIG_SYS_MONITOR_BASE
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
 #endif

 #ifndef CONFIG_RESET_VECTOR_ADDRESS
 #define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
 #endif

 /* High Level Configuration Options */
 #define CONFIG_BOOKE		/* BOOKE */
 #define CONFIG_E500		/* BOOKE e500 family */
 #define CONFIG_MP		/* support multiple processors */

 #define CONFIG_FSL_ELBC		/* Has Enhanced localbus controller */
 #define CONFIG_PCI_INDIRECT_BRIDGE     /* indirect PCI bridge support */
 #define CONFIG_PCIE1		/* PCIE controller 1 (slot 1) */
 #define CONFIG_PCIE2		/* PCIE controller 2 (slot 2) */
 #define CONFIG_PCIE3		/* PCIE controller 3 (slot 3) */
 #define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
 #define CONFIG_FSL_PCIE_RESET	/* need PCIe reset errata */
 #define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
 #define CONFIG_FSL_LAW		/* Use common FSL init code */

 #ifndef __ASSEMBLY__
 extern unsigned long get_clock_freq(void);
 #endif

 #define CONFIG_SYS_CLK_FREQ	66666666
 #define CONFIG_DDR_CLK_FREQ	CONFIG_SYS_CLK_FREQ

 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
 #define CONFIG_L2_CACHE			/* toggle L2 cache */
 #define CONFIG_BTB			/* toggle branch predition */
 #define CONFIG_HWCONFIG

 #define CONFIG_ENABLE_36BIT_PHYS

 #define CONFIG_SYS_MEMTEST_START	0x01000000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x02000000

 #define CONFIG_PANIC_HANG	/* do not reset board on panic */

 /* Implement conversion of addresses in the LBC */
 #define CONFIG_SYS_LBC_LBCR		0x00000000
 #define CONFIG_SYS_LBC_LCRR		LCRR_CLKDIV_8

 /* DDR Setup */
 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE

 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	1

 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_FSL_DDR3
 #define CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SYS_SDRAM_SIZE		512u	/* DDR is 512M */
 #define CONFIG_SYS_SPD_BUS_NUM          0
 #define SPD_EEPROM_ADDRESS              0x50
 #define CONFIG_SYS_DDR_RAW_TIMING

 /*
  * Memory map
  *
  * 0x0000_0000	0x1fff_ffff	DDR			512M cacheable
  * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
  * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
  * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
  * 0xff00_0000	0xff3f_ffff	DPAA_QBMAN		4M cacheable
  * 0xff60_0000	0xff7f_ffff	CCSR			2M non-cacheable
  * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K cacheable TLB0
  *
  * Localbus non-cacheable
  *
  * 0xec00_0000	0xefff_ffff	NOR flash		64M non-cacheable
  * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
  */

 /*
  * Local Bus Definitions
  */
 #define CONFIG_SYS_FLASH_BASE		0xec000000 /* start of FLASH 64M */
 #define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE

 #define CONFIG_FLASH_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
 				| BR_PS_16 | BR_V)
 #define CONFIG_FLASH_OR_PRELIM	0xfc000ff7

 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* sectors per device */
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

 #define CONFIG_BOARD_EARLY_INIT_F	/* call board_early_init_f function */
 #define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */

 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR	0xffd00000	/* Initial L1 address */
 #define CONFIG_SYS_INIT_RAM_SIZE	0x00004000/* Size of used area in RAM */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
 					GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_LEN	(768 * 1024)	  /* Reserve 512 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN	(6 * 1024 * 1024) /* Reserved for malloc */

 #define CONFIG_SYS_NAND_BASE		0xffa00000
 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE

 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_CMD_NAND
 #define CONFIG_NAND_FSL_ELBC
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)

 /* NAND flash config */
 #define CONFIG_SYS_NAND_BR_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
 				| BR_PS_8		/* Port Size = 8bit */ \
 				| BR_MS_FCM		/* MSEL = FCM */ \
 				| BR_V)			/* valid */
 #define CONFIG_SYS_NAND_OR_PRELIM  (OR_AM_256KB		/* length 256K */ \
 				| OR_FCM_PGS \
 				| OR_FCM_CSCT \
 				| OR_FCM_CST \
 				| OR_FCM_CHT \
 				| OR_FCM_SCY_1 \
 				| OR_FCM_TRLX \
 				| OR_FCM_EHTR)

 #define CONFIG_SYS_BR0_PRELIM	CONFIG_FLASH_BR_PRELIM	/* NOR Base Address */
 #define CONFIG_SYS_OR0_PRELIM	CONFIG_FLASH_OR_PRELIM	/* NOR Options */
 #define CONFIG_SYS_BR1_PRELIM	CONFIG_SYS_NAND_BR_PRELIM
 #define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */

 /* Serial Port */
 #define CONFIG_CONS_INDEX		1
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

 #define CONFIG_SYS_BAUDRATE_TABLE	\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR + 0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR + 0x4600)

 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_FSL_I2C2_SPEED	400000
 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100

 /*
  * I2C2 EEPROM
  */
 #define CONFIG_ID_EEPROM
 #ifdef CONFIG_ID_EEPROM
 #define CONFIG_SYS_I2C_EEPROM_NXID
 #endif
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_EEPROM_BUS_NUM		0

 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
  */

 /* controller 3, Slot 1, tgtid 3, Base address b000 */
 #define CONFIG_SYS_PCIE3_NAME		"Slot 3"
 #define CONFIG_SYS_PCIE3_MEM_VIRT	0x80000000
 #define CONFIG_SYS_PCIE3_MEM_BUS	0x80000000
 #define CONFIG_SYS_PCIE3_MEM_PHYS	0x80000000
 #define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE3_IO_VIRT	0xffc00000
 #define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE3_IO_PHYS	0xffc00000
 #define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */

 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
 #define CONFIG_SYS_PCIE2_NAME		"Slot 2"
 #define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
 #define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
 #define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
 #define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
 #define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
 #define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */

 /* controller 1, Slot 2, tgtid 1, Base address a000 */
 #define CONFIG_SYS_PCIE1_NAME		"Slot 1"
 #define CONFIG_SYS_PCIE1_MEM_VIRT	0xc0000000
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xc0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	0xc0000000
 #define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
 #define CONFIG_SYS_PCIE1_IO_VIRT	0xffc20000
 #define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
 #define CONFIG_SYS_PCIE1_IO_PHYS	0xffc20000
 #define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */

 #if defined(CONFIG_PCI)
 #define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
 #endif	/* CONFIG_PCI */

 /*
  * Environment
  */
 #define CONFIG_ENV_OVERWRITE

 #define CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */

 #define CONFIG_LOADS_ECHO		/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */

 /*
  * Command line configuration.
  */
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_REGINFO

 #if defined(CONFIG_PCI)
 #define CONFIG_CMD_PCI
 #endif

 /*
  * USB
  */
 #define CONFIG_HAS_FSL_DR_USB
 #ifdef CONFIG_HAS_FSL_DR_USB
 #define CONFIG_USB_EHCI

 #ifdef CONFIG_USB_EHCI
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_USB_EHCI_FSL
 #define CONFIG_DOS_PARTITION
 #endif
 #endif

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
 #define CONFIG_CMDLINE_EDITING		/* Command-line editing */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
 #define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
 #endif
 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
 #define CONFIG_SYS_MAXARGS	16		/* max number of command args */
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ	(64 << 20)   /* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN	(64 << 20)   /* Increase max gunzip size */

 /*
  * Environment Configuration
  */
 #define CONFIG_BOOTFILE		"uImage"
 #define CONFIG_UBOOTPATH	(u-boot.bin) /* U-Boot image on TFTP server */

 /* default location for tftp and bootm */
 #define CONFIG_LOADADDR		1000000


 #define CONFIG_BAUDRATE	115200

 /* Qman/Bman */
 #define CONFIG_SYS_DPAA_QBMAN		/* support Q/Bman */
 #define CONFIG_SYS_QMAN_MEM_BASE	0xff000000
 #define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
 #define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
 #define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
 #define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
 #define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
 #define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
 					CONFIG_SYS_QMAN_CENA_SIZE)
 #define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_QMAN_SWP_ISDR_REG	0xE08
 #define CONFIG_SYS_BMAN_MEM_BASE	0xff200000
 #define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
 #define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
 #define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
 #define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
 #define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
 #define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
 					CONFIG_SYS_BMAN_CENA_SIZE)
 #define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
 #define CONFIG_SYS_BMAN_SWP_ISDR_REG	0xE08

 /* For FM */
 #define CONFIG_SYS_DPAA_FMAN
 #define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */

 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_FMAN_ENET
 #define CONFIG_PHY_ATHEROS
 #endif

 /* Default address of microcode for the Linux Fman driver */
 /* QE microcode/firmware address */
 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 #define CONFIG_SYS_FMAN_FW_ADDR	0xEFF00000
 #define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
 #define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

 #ifdef CONFIG_FMAN_ENET
 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR	0x1
 #define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR	0x2

 #define CONFIG_SYS_TBIPA_VALUE	8
 #define CONFIG_MII		/* MII PHY management */
 #define CONFIG_ETHPRIME		"FM1@DTSEC1"
 #endif

 #define CONFIG_EXTRA_ENV_SETTINGS	\
 	"netdev=eth0\0"						\
 	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
 	"loadaddr=1000000\0"					\
 	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
 	"tftpflash=tftpboot $loadaddr $uboot; "			\
 		"protect off $ubootaddr +$filesize; "		\
 		"erase $ubootaddr +$filesize; "			\
 		"cp.b $loadaddr $ubootaddr $filesize; "		\
 		"protect on $ubootaddr +$filesize; "		\
 		"cmp.b $loadaddr $ubootaddr $filesize\0"	\
 	"consoledev=ttyS0\0"					\
 	"ramdiskaddr=2000000\0"					\
 	"ramdiskfile=rootfs.ext2.gz.uboot\0"			\
 	"fdtaddr=1e00000\0"					\
 	"fdtfile=p1023rdb.dtb\0"				\
 	"othbootargs=ramdisk_size=600000\0"			\
 	"bdev=sda1\0"						\
 	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"

 #define CONFIG_HDBOOT					\
 	"setenv bootargs root=/dev/$bdev rw "		\
 	"console=$consoledev,$baudrate $othbootargs;"	\
 	"tftp $loadaddr $bootfile;"			\
 	"tftp $fdtaddr $fdtfile;"			\
 	"bootm $loadaddr - $fdtaddr"

 #define CONFIG_NFSBOOTCOMMAND						\
 	"setenv bootargs root=/dev/nfs rw "				\
 	"nfsroot=$serverip:$rootpath "					\
 	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 	"console=$consoledev,$baudrate $othbootargs;"			\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr - $fdtaddr"

 #define CONFIG_RAMBOOTCOMMAND						\
 	"setenv bootargs root=/dev/ram rw "				\
 	"console=$consoledev,$baudrate $othbootargs;"			\
 	"tftp $ramdiskaddr $ramdiskfile;"				\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr $ramdiskaddr $fdtaddr"

 #define CONFIG_BOOTCOMMAND		CONFIG_RAMBOOTCOMMAND

 #endif	/* __CONFIG_H */
	/*
	* Copyright 2013 Freescale Semiconductor, Inc.
	*
	* Authors: Roy Zang <tie-fei.zang@freescale.com>
	* Chunhe Lan <Chunhe.Lan@freescale.com>
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#ifndef CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_TEXT_BASE 0xeff40000
	#endif

	#ifndef CONFIG_SYS_MONITOR_BASE
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	#endif

	#ifndef CONFIG_RESET_VECTOR_ADDRESS
	#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
	#endif

	/* High Level Configuration Options */
	#define CONFIG_BOOKE /* BOOKE */
	#define CONFIG_E500 /* BOOKE e500 family */
	#define CONFIG_MP /* support multiple processors */

	#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */
	#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
	#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
	#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
	#define CONFIG_PCIE3 /* PCIE controller 3 (slot 3) */
	#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
	#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */
	#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
	#define CONFIG_FSL_LAW /* Use common FSL init code */

	#ifndef __ASSEMBLY__
	extern unsigned long get_clock_freq(void);
	#endif

	#define CONFIG_SYS_CLK_FREQ 66666666
	#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ

	/*
	* These can be toggled for performance analysis, otherwise use default.
	*/
	#define CONFIG_L2_CACHE /* toggle L2 cache */
	#define CONFIG_BTB /* toggle branch predition */
	#define CONFIG_HWCONFIG

	#define CONFIG_ENABLE_36BIT_PHYS

	#define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x02000000

	#define CONFIG_PANIC_HANG /* do not reset board on panic */

	/* Implement conversion of addresses in the LBC */
	#define CONFIG_SYS_LBC_LBCR 0x00000000
	#define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8

	/* DDR Setup */
	#define CONFIG_VERY_BIG_RAM
	#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE

	#define CONFIG_DIMM_SLOTS_PER_CTLR 1
	#define CONFIG_CHIP_SELECTS_PER_CTRL 1

	#define CONFIG_DDR_SPD
	#define CONFIG_SYS_FSL_DDR3
	#define CONFIG_FSL_DDR_INTERACTIVE
	#define CONFIG_SYS_SDRAM_SIZE 512u /* DDR is 512M */
	#define CONFIG_SYS_SPD_BUS_NUM 0
	#define SPD_EEPROM_ADDRESS 0x50
	#define CONFIG_SYS_DDR_RAW_TIMING

	/*
	* Memory map
	*
	* 0x0000_0000 0x1fff_ffff DDR 512M cacheable
	* 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable
	* 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable
	* 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable
	* 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M cacheable
	* 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable
	* 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable TLB0
	*
	* Localbus non-cacheable
	*
	* 0xec00_0000 0xefff_ffff NOR flash 64M non-cacheable
	* 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable
	*/

	/*
	* Local Bus Definitions
	*/
	#define CONFIG_SYS_FLASH_BASE 0xec000000 /* start of FLASH 64M */
	#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE

	#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
	\| BR_PS_16 \| BR_V)
	#define CONFIG_FLASH_OR_PRELIM 0xfc000ff7

	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_SYS_FLASH_EMPTY_INFO
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f function */
	#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */

	#define CONFIG_SYS_INIT_RAM_LOCK
	#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */
	#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* Size of used area in RAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
	GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_LEN (768 * 1024) /* Reserve 512 kB for Mon */
	#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */

	#define CONFIG_SYS_NAND_BASE 0xffa00000
	#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE

	#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_CMD_NAND
	#define CONFIG_NAND_FSL_ELBC
	#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)

	/* NAND flash config */
	#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
	\| (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
	\| BR_PS_8 /* Port Size = 8bit */ \
	\| BR_MS_FCM /* MSEL = FCM */ \
	\| BR_V) /* valid */
	#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \
	\| OR_FCM_PGS \
	\| OR_FCM_CSCT \
	\| OR_FCM_CST \
	\| OR_FCM_CHT \
	\| OR_FCM_SCY_1 \
	\| OR_FCM_TRLX \
	\| OR_FCM_EHTR)

	#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */
	#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */
	#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
	#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */

	/* Serial Port */
	#define CONFIG_CONS_INDEX 1
	#undef CONFIG_SERIAL_SOFTWARE_FIFO
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100

	/*
	* I2C2 EEPROM
	*/
	#define CONFIG_ID_EEPROM
	#ifdef CONFIG_ID_EEPROM
	#define CONFIG_SYS_I2C_EEPROM_NXID
	#endif
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_EEPROM_BUS_NUM 0

	/*
	* General PCI
	* Memory space is mapped 1-1, but I/O space must start from 0.
	*/

	/* controller 3, Slot 1, tgtid 3, Base address b000 */
	#define CONFIG_SYS_PCIE3_NAME "Slot 3"
	#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000
	#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000
	#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000
	#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000
	#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
	#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000
	#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */

	/* controller 2, direct to uli, tgtid 2, Base address 9000 */
	#define CONFIG_SYS_PCIE2_NAME "Slot 2"
	#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
	#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
	#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
	#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
	#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
	#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000
	#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */

	/* controller 1, Slot 2, tgtid 1, Base address a000 */
	#define CONFIG_SYS_PCIE1_NAME "Slot 1"
	#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
	#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
	#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
	#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
	#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000
	#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
	#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000
	#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */

	#if defined(CONFIG_PCI)
	#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#endif /* CONFIG_PCI */

	/*
	* Environment
	*/
	#define CONFIG_ENV_OVERWRITE

	#define CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE 0x2000
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */

	#define CONFIG_LOADS_ECHO /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */

	/*
	* Command line configuration.
	*/
	#define CONFIG_CMD_IRQ
	#define CONFIG_CMD_REGINFO

	#if defined(CONFIG_PCI)
	#define CONFIG_CMD_PCI
	#endif

	/*
	* USB
	*/
	#define CONFIG_HAS_FSL_DR_USB
	#ifdef CONFIG_HAS_FSL_DR_USB
	#define CONFIG_USB_EHCI

	#ifdef CONFIG_USB_EHCI
	#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
	#define CONFIG_USB_EHCI_FSL
	#define CONFIG_DOS_PARTITION
	#endif
	#endif

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_CMDLINE_EDITING /* Command-line editing */
	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 64 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	/*
	* Environment Configuration
	*/
	#define CONFIG_BOOTFILE "uImage"
	#define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */

	/* default location for tftp and bootm */
	#define CONFIG_LOADADDR 1000000


	#define CONFIG_BAUDRATE 115200

	/* Qman/Bman */
	#define CONFIG_SYS_DPAA_QBMAN /* support Q/Bman */
	#define CONFIG_SYS_QMAN_MEM_BASE 0xff000000
	#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
	#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000
	#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
	#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
	#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
	#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
	CONFIG_SYS_QMAN_CENA_SIZE)
	#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
	#define CONFIG_SYS_BMAN_MEM_BASE 0xff200000
	#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
	#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000
	#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
	#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
	#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
	#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
	CONFIG_SYS_BMAN_CENA_SIZE)
	#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
	#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08

	/* For FM */
	#define CONFIG_SYS_DPAA_FMAN
	#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */

	#ifdef CONFIG_SYS_DPAA_FMAN
	#define CONFIG_FMAN_ENET
	#define CONFIG_PHY_ATHEROS
	#endif

	/* Default address of microcode for the Linux Fman driver */
	/* QE microcode/firmware address */
	#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
	#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
	#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
	#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)

	#ifdef CONFIG_FMAN_ENET
	#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x1
	#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x2

	#define CONFIG_SYS_TBIPA_VALUE 8
	#define CONFIG_MII /* MII PHY management */
	#define CONFIG_ETHPRIME "FM1@DTSEC1"
	#endif

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
	"loadaddr=1000000\0" \
	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
	"tftpflash=tftpboot $loadaddr $uboot; " \
	"protect off $ubootaddr +$filesize; " \
	"erase $ubootaddr +$filesize; " \
	"cp.b $loadaddr $ubootaddr $filesize; " \
	"protect on $ubootaddr +$filesize; " \
	"cmp.b $loadaddr $ubootaddr $filesize\0" \
	"consoledev=ttyS0\0" \
	"ramdiskaddr=2000000\0" \
	"ramdiskfile=rootfs.ext2.gz.uboot\0" \
	"fdtaddr=1e00000\0" \
	"fdtfile=p1023rdb.dtb\0" \
	"othbootargs=ramdisk_size=600000\0" \
	"bdev=sda1\0" \
	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"

	#define CONFIG_HDBOOT \
	"setenv bootargs root=/dev/$bdev rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND

	#endif /* __CONFIG_H */