include/configs/ls1088a_common.h - platform/external/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2017-2018 NXP
  */

 #ifndef __LS1088_COMMON_H
 #define __LS1088_COMMON_H

 /* SPL build */
 #ifdef CONFIG_SPL_BUILD
 #define SPL_NO_BOARDINFO
 #define SPL_NO_QIXIS
 #define SPL_NO_PCI
 #define SPL_NO_ENV
 #define SPL_NO_RTC
 #define SPL_NO_USB
 #define SPL_NO_SATA
 #define SPL_NO_QSPI
 #define SPL_NO_IFC
 #undef CONFIG_DISPLAY_CPUINFO
 #endif

 #define CONFIG_REMAKE_ELF

 #include <asm/arch/stream_id_lsch3.h>
 #include <asm/arch/config.h>
 #include <asm/arch/soc.h>

 #define LS1088ARDB_PB_BOARD            0x4A
 /* Link Definitions */
 #ifdef CONFIG_TFABOOT
 #define CONFIG_SYS_INIT_SP_ADDR		CONFIG_SYS_TEXT_BASE
 #else
 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
 #endif

 /* Link Definitions */
 #define CONFIG_SYS_FSL_QSPI_BASE	0x20000000

 #define CONFIG_SKIP_LOWLEVEL_INIT

 #define CONFIG_VERY_BIG_RAM
 #define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000UL
 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_SYS_DDR_BLOCK2_BASE	0x8080000000ULL
 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS	1
 /*
  * SMP Definitinos
  */
 #define CPU_RELEASE_ADDR		secondary_boot_addr

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2048 * 1024)

 /* I2C */
 #ifndef CONFIG_DM_I2C
 #define CONFIG_SYS_I2C
 #endif


 /* Serial Port */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE     1
 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0) / 2)

 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

 #if !defined(SPL_NO_IFC) || defined(CONFIG_TARGET_LS1088AQDS)
 /* IFC */
 #define CONFIG_FSL_IFC
 #endif

 /*
  * During booting, IFC is mapped at the region of 0x30000000.
  * But this region is limited to 256MB. To accommodate NOR, promjet
  * and FPGA. This region is divided as below:
  * 0x30000000 - 0x37ffffff : 128MB : NOR flash
  * 0x38000000 - 0x3BFFFFFF : 64MB  : Promjet
  * 0x3C000000 - 0x40000000 : 64MB  : FPGA etc
  *
  * To accommodate bigger NOR flash and other devices, we will map IFC
  * chip selects to as below:
  * 0x5_1000_0000..0x5_1fff_ffff	Memory Hole
  * 0x5_2000_0000..0x5_3fff_ffff	IFC CSx (FPGA, NAND and others 512MB)
  * 0x5_4000_0000..0x5_7fff_ffff	ASIC or others 1GB
  * 0x5_8000_0000..0x5_bfff_ffff	IFC CS0 1GB (NOR/Promjet)
  * 0x5_C000_0000..0x5_ffff_ffff	IFC CS1 1GB (NOR/Promjet)
  *
  * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
  * CONFIG_SYS_FLASH_BASE has the final address (core view)
  * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
  * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
  * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
  */

 #define CONFIG_SYS_FLASH_BASE			0x580000000ULL
 #define CONFIG_SYS_FLASH_BASE_PHYS		0x80000000
 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000

 #define CONFIG_SYS_FLASH1_BASE_PHYS		0xC0000000
 #define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY	0x8000000

 #ifndef __ASSEMBLY__
 unsigned long long get_qixis_addr(void);
 #endif

 #define QIXIS_BASE				get_qixis_addr()
 #define QIXIS_BASE_PHYS				0x20000000
 #define QIXIS_BASE_PHYS_EARLY			0xC000000


 #define CONFIG_SYS_NAND_BASE			0x530000000ULL
 #define CONFIG_SYS_NAND_BASE_PHYS		0x30000000


 /* MC firmware */
 /* TODO Actual DPL max length needs to be confirmed with the MC FW team */
 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH	    0x20000
 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET    0x00F00000
 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH	    0x20000
 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET    0x00F20000
 #define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH	0x200000
 #define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET	0x07000000

 /* Define phy_reset function to boot the MC based on mcinitcmd.
  * This happens late enough to properly fixup u-boot env MAC addresses.
  */
 #define CONFIG_RESET_PHY_R

 /*
  * Carve out a DDR region which will not be used by u-boot/Linux
  *
  * It will be used by MC and Debug Server. The MC region must be
  * 512MB aligned, so the min size to hide is 512MB.
  */

 #if defined(CONFIG_FSL_MC_ENET)
 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE		(128UL * 1024 * 1024)
 #endif

 /* Miscellaneous configurable options */
 #define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

 /* SATA */
 #ifdef CONFIG_SCSI
 #define CONFIG_SCSI_AHCI_PLAT
 #define CONFIG_SYS_SATA1		AHCI_BASE_ADDR1

 #define CONFIG_SYS_SCSI_MAX_SCSI_ID	1
 #define CONFIG_SYS_SCSI_MAX_LUN		1
 #define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 					CONFIG_SYS_SCSI_MAX_LUN)
 #endif

 /* Physical Memory Map */
 #define CONFIG_CHIP_SELECTS_PER_CTRL	4

 #define CONFIG_HWCONFIG
 #define HWCONFIG_BUFFER_SIZE		128

 /* #define CONFIG_DISPLAY_CPUINFO */

 #ifndef SPL_NO_ENV
 /* Allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE

 /* Initial environment variables */
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
 	"loadaddr=0x80100000\0"			\
 	"kernel_addr=0x100000\0"		\
 	"ramdisk_addr=0x800000\0"		\
 	"ramdisk_size=0x2000000\0"		\
 	"fdt_high=0xa0000000\0"			\
 	"initrd_high=0xffffffffffffffff\0"	\
 	"kernel_start=0x581000000\0"		\
 	"kernel_load=0xa0000000\0"		\
 	"kernel_size=0x2800000\0"		\
 	"console=ttyAMA0,38400n8\0"		\
 	"mcinitcmd=fsl_mc start mc 0x580a00000"	\
 	" 0x580e00000 \0"

 #ifndef CONFIG_TFABOOT
 #if defined(CONFIG_QSPI_BOOT)
 #define CONFIG_BOOTCOMMAND	"sf probe 0:0;" \
 				"sf read 0x80001000 0xd00000 0x100000;"\
 				" fsl_mc lazyapply dpl 0x80001000 &&" \
 				" sf read $kernel_load $kernel_start" \
 				" $kernel_size && bootm $kernel_load"
 #elif defined(CONFIG_SD_BOOT)
 #define CONFIG_BOOTCOMMAND	"mmcinfo;mmc read 0x80001000 0x6800 0x800;"\
 				" fsl_mc lazyapply dpl 0x80001000 &&" \
 				" mmc read $kernel_load $kernel_start" \
 				" $kernel_size && bootm $kernel_load"
 #else /* NOR BOOT*/
 #define CONFIG_BOOTCOMMAND	"fsl_mc lazyapply dpl 0x580d00000 &&" \
 				" cp.b $kernel_start $kernel_load" \
 				" $kernel_size && bootm $kernel_load"
 #endif
 #endif /* CONFIG_TFABOOT  */
 #endif

 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE /* Boot args buffer */
 #define CONFIG_SYS_MAXARGS		64	/* max command args */

 #ifdef CONFIG_SPL
 #define CONFIG_SPL_BSS_START_ADDR      0x80100000
 #define CONFIG_SPL_BSS_MAX_SIZE                0x00100000
 #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
 #define CONFIG_SPL_MAX_SIZE            0x16000
 #define CONFIG_SPL_STACK               (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
 #define CONFIG_SPL_TARGET              "u-boot-with-spl.bin"

 #define CONFIG_SYS_SPL_MALLOC_SIZE     0x00100000
 #define CONFIG_SYS_SPL_MALLOC_START    0x80200000

 #ifdef CONFIG_NXP_ESBC
 #define CONFIG_U_BOOT_HDR_SIZE		(16 << 10)
 /*
  * HDR would be appended at end of image and copied to DDR along
  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  * size increases then increase this size in case of secure boot as
  * it uses raw u-boot image instead of fit image.
  */
 #define CONFIG_SYS_MONITOR_LEN         (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
 #else
 #define CONFIG_SYS_MONITOR_LEN         0x100000
 #endif /* ifdef CONFIG_NXP_ESBC */

 #endif
 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */

 #endif /* __LS1088_COMMON_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2017-2018 NXP
	*/

	#ifndef __LS1088_COMMON_H
	#define __LS1088_COMMON_H

	/* SPL build */
	#ifdef CONFIG_SPL_BUILD
	#define SPL_NO_BOARDINFO
	#define SPL_NO_QIXIS
	#define SPL_NO_PCI
	#define SPL_NO_ENV
	#define SPL_NO_RTC
	#define SPL_NO_USB
	#define SPL_NO_SATA
	#define SPL_NO_QSPI
	#define SPL_NO_IFC
	#undef CONFIG_DISPLAY_CPUINFO
	#endif

	#define CONFIG_REMAKE_ELF

	#include <asm/arch/stream_id_lsch3.h>
	#include <asm/arch/config.h>
	#include <asm/arch/soc.h>

	#define LS1088ARDB_PB_BOARD 0x4A
	/* Link Definitions */
	#ifdef CONFIG_TFABOOT
	#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
	#else
	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
	#endif

	/* Link Definitions */
	#define CONFIG_SYS_FSL_QSPI_BASE 0x20000000

	#define CONFIG_SKIP_LOWLEVEL_INIT

	#define CONFIG_VERY_BIG_RAM
	#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
	#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
	#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 1
	/*
	* SMP Definitinos
	*/
	#define CPU_RELEASE_ADDR secondary_boot_addr

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)

	/* I2C */
	#ifndef CONFIG_DM_I2C
	#define CONFIG_SYS_I2C
	#endif


	/* Serial Port */
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)

	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }

	#if !defined(SPL_NO_IFC) \|\| defined(CONFIG_TARGET_LS1088AQDS)
	/* IFC */
	#define CONFIG_FSL_IFC
	#endif

	/*
	* During booting, IFC is mapped at the region of 0x30000000.
	* But this region is limited to 256MB. To accommodate NOR, promjet
	* and FPGA. This region is divided as below:
	* 0x30000000 - 0x37ffffff : 128MB : NOR flash
	* 0x38000000 - 0x3BFFFFFF : 64MB : Promjet
	* 0x3C000000 - 0x40000000 : 64MB : FPGA etc
	*
	* To accommodate bigger NOR flash and other devices, we will map IFC
	* chip selects to as below:
	* 0x5_1000_0000..0x5_1fff_ffff Memory Hole
	* 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
	* 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
	* 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
	* 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
	*
	* For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
	* CONFIG_SYS_FLASH_BASE has the final address (core view)
	* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
	* CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
	* CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
	*/

	#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
	#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
	#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000

	#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000
	#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000

	#ifndef __ASSEMBLY__
	unsigned long long get_qixis_addr(void);
	#endif

	#define QIXIS_BASE get_qixis_addr()
	#define QIXIS_BASE_PHYS 0x20000000
	#define QIXIS_BASE_PHYS_EARLY 0xC000000


	#define CONFIG_SYS_NAND_BASE 0x530000000ULL
	#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000


	/* MC firmware */
	/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
	#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
	#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
	#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
	#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
	#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
	#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000

	/* Define phy_reset function to boot the MC based on mcinitcmd.
	* This happens late enough to properly fixup u-boot env MAC addresses.
	*/
	#define CONFIG_RESET_PHY_R

	/*
	* Carve out a DDR region which will not be used by u-boot/Linux
	*
	* It will be used by MC and Debug Server. The MC region must be
	* 512MB aligned, so the min size to hide is 512MB.
	*/

	#if defined(CONFIG_FSL_MC_ENET)
	#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (128UL * 1024 * 1024)
	#endif

	/* Miscellaneous configurable options */
	#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)

	/* SATA */
	#ifdef CONFIG_SCSI
	#define CONFIG_SCSI_AHCI_PLAT
	#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1

	#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
	#define CONFIG_SYS_SCSI_MAX_LUN 1
	#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
	CONFIG_SYS_SCSI_MAX_LUN)
	#endif

	/* Physical Memory Map */
	#define CONFIG_CHIP_SELECTS_PER_CTRL 4

	#define CONFIG_HWCONFIG
	#define HWCONFIG_BUFFER_SIZE 128

	/* #define CONFIG_DISPLAY_CPUINFO */

	#ifndef SPL_NO_ENV
	/* Allow to overwrite serial and ethaddr */
	#define CONFIG_ENV_OVERWRITE

	/* Initial environment variables */
	#define CONFIG_EXTRA_ENV_SETTINGS \
	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	"loadaddr=0x80100000\0" \
	"kernel_addr=0x100000\0" \
	"ramdisk_addr=0x800000\0" \
	"ramdisk_size=0x2000000\0" \
	"fdt_high=0xa0000000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"kernel_start=0x581000000\0" \
	"kernel_load=0xa0000000\0" \
	"kernel_size=0x2800000\0" \
	"console=ttyAMA0,38400n8\0" \
	"mcinitcmd=fsl_mc start mc 0x580a00000" \
	" 0x580e00000 \0"

	#ifndef CONFIG_TFABOOT
	#if defined(CONFIG_QSPI_BOOT)
	#define CONFIG_BOOTCOMMAND "sf probe 0:0;" \
	"sf read 0x80001000 0xd00000 0x100000;"\
	" fsl_mc lazyapply dpl 0x80001000 &&" \
	" sf read $kernel_load $kernel_start" \
	" $kernel_size && bootm $kernel_load"
	#elif defined(CONFIG_SD_BOOT)
	#define CONFIG_BOOTCOMMAND "mmcinfo;mmc read 0x80001000 0x6800 0x800;"\
	" fsl_mc lazyapply dpl 0x80001000 &&" \
	" mmc read $kernel_load $kernel_start" \
	" $kernel_size && bootm $kernel_load"
	#else /* NOR BOOT*/
	#define CONFIG_BOOTCOMMAND "fsl_mc lazyapply dpl 0x580d00000 &&" \
	" cp.b $kernel_start $kernel_load" \
	" $kernel_size && bootm $kernel_load"
	#endif
	#endif /* CONFIG_TFABOOT */
	#endif

	/* Monitor Command Prompt */
	#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
	#define CONFIG_SYS_MAXARGS 64 /* max command args */

	#ifdef CONFIG_SPL
	#define CONFIG_SPL_BSS_START_ADDR 0x80100000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
	#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
	#define CONFIG_SPL_MAX_SIZE 0x16000
	#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
	#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"

	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
	#define CONFIG_SYS_SPL_MALLOC_START 0x80200000

	#ifdef CONFIG_NXP_ESBC
	#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
	/*
	* HDR would be appended at end of image and copied to DDR along
	* with U-Boot image. Here u-boot max. size is 512K. So if binary
	* size increases then increase this size in case of secure boot as
	* it uses raw u-boot image instead of fit image.
	*/
	#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
	#else
	#define CONFIG_SYS_MONITOR_LEN 0x100000
	#endif /* ifdef CONFIG_NXP_ESBC */

	#endif
	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */

	#endif /* __LS1088_COMMON_H */