| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright 2021 Gateworks Corporation |
| */ |
| |
| #include <fdt_support.h> |
| #include <init.h> |
| #include <led.h> |
| #include <miiphy.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/sys_proto.h> |
| |
| #include "eeprom.h" |
| |
| int board_phys_sdram_size(phys_size_t *size) |
| { |
| if (!size) |
| return -EINVAL; |
| |
| *size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); |
| |
| return 0; |
| } |
| |
| int board_fit_config_name_match(const char *name) |
| { |
| int i = 0; |
| const char *dtb; |
| static char init; |
| char buf[32]; |
| |
| do { |
| dtb = eeprom_get_dtb_name(i++, buf, sizeof(buf)); |
| if (!strcmp(dtb, name)) { |
| if (!init++) |
| printf("DTB : %s\n", name); |
| return 0; |
| } |
| } while (dtb); |
| |
| return -1; |
| } |
| |
| static int __maybe_unused setup_fec(void) |
| { |
| struct iomuxc_gpr_base_regs *gpr = |
| (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR; |
| |
| #ifndef CONFIG_IMX8MP |
| /* Use 125M anatop REF_CLK1 for ENET1, not from external */ |
| clrsetbits_le32(&gpr->gpr[1], 0x2000, 0); |
| #else |
| /* Enable RGMII TX clk output */ |
| setbits_le32(&gpr->gpr[1], BIT(22)); |
| #endif |
| |
| return 0; |
| } |
| |
| static int __maybe_unused setup_eqos(void) |
| { |
| struct iomuxc_gpr_base_regs *gpr = |
| (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR; |
| |
| /* set INTF as RGMII, enable RGMII TXC clock */ |
| clrsetbits_le32(&gpr->gpr[1], |
| IOMUXC_GPR_GPR1_GPR_ENET_QOS_INTF_SEL_MASK, BIT(16)); |
| setbits_le32(&gpr->gpr[1], BIT(19) | BIT(21)); |
| |
| return set_clk_eqos(ENET_125MHZ); |
| } |
| |
| #if (IS_ENABLED(CONFIG_NET)) |
| int board_phy_config(struct phy_device *phydev) |
| { |
| unsigned short val; |
| ofnode node; |
| |
| switch (phydev->phy_id) { |
| case 0x2000a231: /* TI DP83867 GbE PHY */ |
| puts("DP83867 "); |
| /* LED configuration */ |
| val = 0; |
| val |= 0x5 << 4; /* LED1(Amber;Speed) : 1000BT link */ |
| val |= 0xb << 8; /* LED2(Green;Link/Act): blink for TX/RX act */ |
| phy_write(phydev, MDIO_DEVAD_NONE, 24, val); |
| break; |
| case 0xd565a401: /* MaxLinear GPY111 */ |
| puts("GPY111 "); |
| node = phy_get_ofnode(phydev); |
| if (ofnode_valid(node)) { |
| u32 rx_delay, tx_delay; |
| |
| rx_delay = ofnode_read_u32_default(node, "rx-internal-delay-ps", 2000); |
| tx_delay = ofnode_read_u32_default(node, "tx-internal-delay-ps", 2000); |
| val = phy_read(phydev, MDIO_DEVAD_NONE, 0x17); |
| val &= ~((0x7 << 12) | (0x7 << 8)); |
| val |= (rx_delay / 500) << 12; |
| val |= (tx_delay / 500) << 8; |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x17, val); |
| } |
| break; |
| } |
| |
| if (phydev->drv->config) |
| phydev->drv->config(phydev); |
| |
| return 0; |
| } |
| #endif // IS_ENABLED(CONFIG_NET) |
| |
| int board_init(void) |
| { |
| venice_eeprom_init(1); |
| |
| if (IS_ENABLED(CONFIG_FEC_MXC)) |
| setup_fec(); |
| if (IS_ENABLED(CONFIG_DWC_ETH_QOS)) |
| setup_eqos(); |
| |
| return 0; |
| } |
| |
| int board_late_init(void) |
| { |
| const char *str; |
| char env[32]; |
| int ret, i; |
| u8 enetaddr[6]; |
| char fdt[64]; |
| |
| /* Set board serial/model */ |
| if (!env_get("serial#")) |
| env_set_ulong("serial#", eeprom_get_serial()); |
| env_set("model", eeprom_get_model()); |
| |
| /* Set fdt_file vars */ |
| i = 0; |
| do { |
| str = eeprom_get_dtb_name(i, fdt, sizeof(fdt)); |
| if (str) { |
| sprintf(env, "fdt_file%d", i + 1); |
| strcat(fdt, ".dtb"); |
| env_set(env, fdt); |
| } |
| i++; |
| } while (str); |
| |
| /* Set mac addrs */ |
| i = 0; |
| do { |
| if (i) |
| sprintf(env, "eth%daddr", i); |
| else |
| sprintf(env, "ethaddr"); |
| str = env_get(env); |
| if (!str) { |
| ret = eeprom_getmac(i, enetaddr); |
| if (!ret) |
| eth_env_set_enetaddr(env, enetaddr); |
| } |
| i++; |
| } while (!ret); |
| |
| return 0; |
| } |
| |
| int board_mmc_get_env_dev(int devno) |
| { |
| return devno; |
| } |
| |
| int ft_board_setup(void *fdt, struct bd_info *bd) |
| { |
| const char *base_model = eeprom_get_baseboard_model(); |
| char pcbrev; |
| int off; |
| |
| /* set board model dt prop */ |
| fdt_setprop_string(fdt, 0, "board", eeprom_get_model()); |
| |
| if (!strncmp(base_model, "GW73", 4)) { |
| pcbrev = get_pcb_rev(base_model); |
| |
| if (pcbrev > 'B') { |
| printf("adjusting dt for %s\n", base_model); |
| |
| /* |
| * revC replaced PCIe 5-port switch with 4-port |
| * which changed ethernet1 PCIe GbE |
| * from: pcie@0,0/pcie@1,0/pcie@2,4/pcie@6.0 |
| * to: pcie@0,0/pcie@1,0/pcie@2,3/pcie@5.0 |
| */ |
| off = fdt_path_offset(fdt, "ethernet1"); |
| if (off > 0) { |
| u32 reg[5]; |
| |
| fdt_set_name(fdt, off, "pcie@5,0"); |
| off = fdt_parent_offset(fdt, off); |
| fdt_set_name(fdt, off, "pcie@2,3"); |
| memset(reg, 0, sizeof(reg)); |
| reg[0] = cpu_to_fdt32(PCI_DEVFN(3, 0)); |
| fdt_setprop(fdt, off, "reg", reg, sizeof(reg)); |
| } |
| } |
| } |
| |
| return 0; |
| } |