| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * DDR controller configuration for the i.MX7 architecture |
| * |
| * (C) Copyright 2017 CompuLab, Ltd. http://www.compulab.com |
| * |
| * Author: Uri Mashiach <uri.mashiach@compulab.co.il> |
| */ |
| |
| #include <linux/types.h> |
| #include <asm/io.h> |
| #include <asm/arch/imx-regs.h> |
| #include <asm/arch/crm_regs.h> |
| #include <asm/arch/mx7-ddr.h> |
| #include <common.h> |
| #include <linux/delay.h> |
| |
| /* |
| * Routine: mx7_dram_cfg |
| * Description: DDR controller configuration |
| * |
| * @ddrc_regs_val: DDRC registers value |
| * @ddrc_mp_val: DDRC_MP registers value |
| * @ddr_phy_regs_val: DDR_PHY registers value |
| * @calib_param: calibration parameters |
| * |
| */ |
| void mx7_dram_cfg(struct ddrc *ddrc_regs_val, struct ddrc_mp *ddrc_mp_val, |
| struct ddr_phy *ddr_phy_regs_val, |
| struct mx7_calibration *calib_param) |
| { |
| struct src *const src_regs = (struct src *)SRC_BASE_ADDR; |
| struct ddrc *const ddrc_regs = (struct ddrc *)DDRC_IPS_BASE_ADDR; |
| struct ddrc_mp *const ddrc_mp_reg = (struct ddrc_mp *)DDRC_MP_BASE_ADDR; |
| struct ddr_phy *const ddr_phy_regs = |
| (struct ddr_phy *)DDRPHY_IPS_BASE_ADDR; |
| struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs = |
| (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR; |
| int i; |
| |
| /* |
| * iMX7D RM 9.2.4.9.3 Power removal flow Table 9-11. Re-enabling power |
| * row 2 says "Reset controller / PHY by driving core_ddrc_rst = 0 , |
| * aresetn_n = 0, presetn = 0. That means reset everything. |
| */ |
| writel(SRC_DDRC_RCR_DDRC_CORE_RST_MASK | SRC_DDRC_RCR_DDRC_PRST_MASK, |
| &src_regs->ddrc_rcr); |
| |
| /* |
| * iMX7D RM 6.2.7.26 SRC_DDRC_RCR says wait 30 cycles (of unknown). |
| * If we assume this is 30 cycles at 100 MHz (about the rate of a |
| * DRAM bus), that's 300 nS, so waiting 10 uS is more then plenty. |
| */ |
| udelay(10); |
| |
| /* De-assert DDR Controller 'preset' and DDR PHY reset */ |
| clrbits_le32(&src_regs->ddrc_rcr, SRC_DDRC_RCR_DDRC_PRST_MASK); |
| |
| /* DDR controller configuration */ |
| writel(ddrc_regs_val->mstr, &ddrc_regs->mstr); |
| writel(ddrc_regs_val->rfshtmg, &ddrc_regs->rfshtmg); |
| writel(ddrc_mp_val->pctrl_0, &ddrc_mp_reg->pctrl_0); |
| writel(ddrc_regs_val->init1, &ddrc_regs->init1); |
| writel(ddrc_regs_val->init0, &ddrc_regs->init0); |
| writel(ddrc_regs_val->init3, &ddrc_regs->init3); |
| writel(ddrc_regs_val->init4, &ddrc_regs->init4); |
| writel(ddrc_regs_val->init5, &ddrc_regs->init5); |
| writel(ddrc_regs_val->rankctl, &ddrc_regs->rankctl); |
| writel(ddrc_regs_val->dramtmg0, &ddrc_regs->dramtmg0); |
| writel(ddrc_regs_val->dramtmg1, &ddrc_regs->dramtmg1); |
| writel(ddrc_regs_val->dramtmg2, &ddrc_regs->dramtmg2); |
| writel(ddrc_regs_val->dramtmg3, &ddrc_regs->dramtmg3); |
| writel(ddrc_regs_val->dramtmg4, &ddrc_regs->dramtmg4); |
| writel(ddrc_regs_val->dramtmg5, &ddrc_regs->dramtmg5); |
| writel(ddrc_regs_val->dramtmg8, &ddrc_regs->dramtmg8); |
| writel(ddrc_regs_val->zqctl0, &ddrc_regs->zqctl0); |
| writel(ddrc_regs_val->zqctl1, &ddrc_regs->zqctl1); |
| writel(ddrc_regs_val->dfitmg0, &ddrc_regs->dfitmg0); |
| writel(ddrc_regs_val->dfitmg1, &ddrc_regs->dfitmg1); |
| writel(ddrc_regs_val->dfiupd0, &ddrc_regs->dfiupd0); |
| writel(ddrc_regs_val->dfiupd1, &ddrc_regs->dfiupd1); |
| writel(ddrc_regs_val->dfiupd2, &ddrc_regs->dfiupd2); |
| writel(ddrc_regs_val->addrmap0, &ddrc_regs->addrmap0); |
| writel(ddrc_regs_val->addrmap1, &ddrc_regs->addrmap1); |
| writel(ddrc_regs_val->addrmap4, &ddrc_regs->addrmap4); |
| writel(ddrc_regs_val->addrmap5, &ddrc_regs->addrmap5); |
| writel(ddrc_regs_val->addrmap6, &ddrc_regs->addrmap6); |
| writel(ddrc_regs_val->odtcfg, &ddrc_regs->odtcfg); |
| writel(ddrc_regs_val->odtmap, &ddrc_regs->odtmap); |
| |
| /* De-assert DDR Controller 'core_ddrc_rstn' and 'aresetn' */ |
| clrbits_le32(&src_regs->ddrc_rcr, SRC_DDRC_RCR_DDRC_CORE_RST_MASK); |
| |
| /* PHY configuration */ |
| writel(ddr_phy_regs_val->phy_con0, &ddr_phy_regs->phy_con0); |
| writel(ddr_phy_regs_val->phy_con1, &ddr_phy_regs->phy_con1); |
| writel(ddr_phy_regs_val->phy_con4, &ddr_phy_regs->phy_con4); |
| writel(ddr_phy_regs_val->mdll_con0, &ddr_phy_regs->mdll_con0); |
| writel(ddr_phy_regs_val->drvds_con0, &ddr_phy_regs->drvds_con0); |
| writel(ddr_phy_regs_val->offset_wr_con0, &ddr_phy_regs->offset_wr_con0); |
| writel(ddr_phy_regs_val->offset_rd_con0, &ddr_phy_regs->offset_rd_con0); |
| writel(ddr_phy_regs_val->cmd_sdll_con0 | |
| DDR_PHY_CMD_SDLL_CON0_CTRL_RESYNC_MASK, |
| &ddr_phy_regs->cmd_sdll_con0); |
| writel(ddr_phy_regs_val->cmd_sdll_con0 & |
| ~DDR_PHY_CMD_SDLL_CON0_CTRL_RESYNC_MASK, |
| &ddr_phy_regs->cmd_sdll_con0); |
| writel(ddr_phy_regs_val->offset_lp_con0, &ddr_phy_regs->offset_lp_con0); |
| writel(ddr_phy_regs_val->cmd_deskew_con0, |
| &ddr_phy_regs->cmd_deskew_con0); |
| writel(ddr_phy_regs_val->cmd_deskew_con1, |
| &ddr_phy_regs->cmd_deskew_con1); |
| writel(ddr_phy_regs_val->cmd_deskew_con2, |
| &ddr_phy_regs->cmd_deskew_con2); |
| writel(ddr_phy_regs_val->cmd_deskew_con3, |
| &ddr_phy_regs->cmd_deskew_con3); |
| writel(ddr_phy_regs_val->cmd_lvl_con0, &ddr_phy_regs->cmd_lvl_con0); |
| |
| /* calibration */ |
| for (i = 0; i < calib_param->num_val; i++) |
| writel(calib_param->values[i], &ddr_phy_regs->zq_con0); |
| |
| /* Wake_up DDR PHY */ |
| HW_CCM_CCGR_WR(CCGR_IDX_DDR, CCM_CLK_ON_N_N); |
| writel(IOMUXC_GPR_GPR8_ddr_phy_ctrl_wake_up(0xf) | |
| IOMUXC_GPR_GPR8_ddr_phy_dfi_init_start_MASK, |
| &iomuxc_gpr_regs->gpr[8]); |
| HW_CCM_CCGR_WR(CCGR_IDX_DDR, CCM_CLK_ON_R_W); |
| } |
| |
| /* |
| * Routine: imx_ddr_size |
| * Description: extract the current DRAM size from the DDRC registers |
| * |
| * @return: DRAM size |
| */ |
| unsigned int imx_ddr_size(void) |
| { |
| struct ddrc *const ddrc_regs = (struct ddrc *)DDRC_IPS_BASE_ADDR; |
| u32 reg_val, field_val; |
| int bits = 0;/* Number of address bits */ |
| |
| /* Count data bus width bits */ |
| reg_val = readl(&ddrc_regs->mstr); |
| field_val = (reg_val & MSTR_DATA_BUS_WIDTH_MASK) >> MSTR_DATA_BUS_WIDTH_SHIFT; |
| bits += 2 - field_val; |
| /* Count rank address bits */ |
| field_val = (reg_val & MSTR_DATA_ACTIVE_RANKS_MASK) >> MSTR_DATA_ACTIVE_RANKS_SHIFT; |
| if (field_val > 1) |
| bits += field_val - 1; |
| /* Count column address bits */ |
| bits += 2;/* Column address 0 and 1 are fixed mapped */ |
| reg_val = readl(&ddrc_regs->addrmap2); |
| field_val = (reg_val & ADDRMAP2_COL_B2_MASK) >> ADDRMAP2_COL_B2_SHIFT; |
| if (field_val <= 7) |
| bits++; |
| field_val = (reg_val & ADDRMAP2_COL_B3_MASK) >> ADDRMAP2_COL_B3_SHIFT; |
| if (field_val <= 7) |
| bits++; |
| field_val = (reg_val & ADDRMAP2_COL_B4_MASK) >> ADDRMAP2_COL_B4_SHIFT; |
| if (field_val <= 7) |
| bits++; |
| field_val = (reg_val & ADDRMAP2_COL_B5_MASK) >> ADDRMAP2_COL_B5_SHIFT; |
| if (field_val <= 7) |
| bits++; |
| reg_val = readl(&ddrc_regs->addrmap3); |
| field_val = (reg_val & ADDRMAP3_COL_B6_MASK) >> ADDRMAP3_COL_B6_SHIFT; |
| if (field_val <= 7) |
| bits++; |
| field_val = (reg_val & ADDRMAP3_COL_B7_MASK) >> ADDRMAP3_COL_B7_SHIFT; |
| if (field_val <= 7) |
| bits++; |
| field_val = (reg_val & ADDRMAP3_COL_B8_MASK) >> ADDRMAP3_COL_B8_SHIFT; |
| if (field_val <= 7) |
| bits++; |
| field_val = (reg_val & ADDRMAP3_COL_B9_MASK) >> ADDRMAP3_COL_B9_SHIFT; |
| if (field_val <= 7) |
| bits++; |
| reg_val = readl(&ddrc_regs->addrmap4); |
| field_val = (reg_val & ADDRMAP4_COL_B10_MASK) >> ADDRMAP4_COL_B10_SHIFT; |
| if (field_val <= 7) |
| bits++; |
| field_val = (reg_val & ADDRMAP4_COL_B11_MASK) >> ADDRMAP4_COL_B11_SHIFT; |
| if (field_val <= 7) |
| bits++; |
| /* Count row address bits */ |
| reg_val = readl(&ddrc_regs->addrmap5); |
| field_val = (reg_val & ADDRMAP5_ROW_B0_MASK) >> ADDRMAP5_ROW_B0_SHIFT; |
| if (field_val <= 11) |
| bits++; |
| field_val = (reg_val & ADDRMAP5_ROW_B1_MASK) >> ADDRMAP5_ROW_B1_SHIFT; |
| if (field_val <= 11) |
| bits++; |
| field_val = (reg_val & ADDRMAP5_ROW_B2_10_MASK) >> ADDRMAP5_ROW_B2_10_SHIFT; |
| if (field_val <= 11) |
| bits += 9; |
| field_val = (reg_val & ADDRMAP5_ROW_B11_MASK) >> ADDRMAP5_ROW_B11_SHIFT; |
| if (field_val <= 11) |
| bits++; |
| reg_val = readl(&ddrc_regs->addrmap6); |
| field_val = (reg_val & ADDRMAP6_ROW_B12_MASK) >> ADDRMAP6_ROW_B12_SHIFT; |
| if (field_val <= 11) |
| bits++; |
| field_val = (reg_val & ADDRMAP6_ROW_B13_MASK) >> ADDRMAP6_ROW_B13_SHIFT; |
| if (field_val <= 11) |
| bits++; |
| field_val = (reg_val & ADDRMAP6_ROW_B14_MASK) >> ADDRMAP6_ROW_B14_SHIFT; |
| if (field_val <= 11) |
| bits++; |
| field_val = (reg_val & ADDRMAP6_ROW_B15_MASK) >> ADDRMAP6_ROW_B15_SHIFT; |
| if (field_val <= 11) |
| bits++; |
| /* Count bank bits */ |
| reg_val = readl(&ddrc_regs->addrmap1); |
| field_val = (reg_val & ADDRMAP1_BANK_B0_MASK) >> ADDRMAP1_BANK_B0_SHIFT; |
| if (field_val <= 30) |
| bits++; |
| field_val = (reg_val & ADDRMAP1_BANK_B1_MASK) >> ADDRMAP1_BANK_B1_SHIFT; |
| if (field_val <= 30) |
| bits++; |
| field_val = (reg_val & ADDRMAP1_BANK_B2_MASK) >> ADDRMAP1_BANK_B2_SHIFT; |
| if (field_val <= 29) |
| bits++; |
| |
| /* cap to max 2 GB */ |
| if (bits > 31) |
| bits = 31; |
| |
| return 1 << bits; |
| } |