| /* |
| * Copyright 2011, Marvell Semiconductor Inc. |
| * Lei Wen <leiwen@marvell.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| * |
| * Back ported to the 8xx platform (from the 8260 platform) by |
| * Murray.Jensen@cmst.csiro.au, 27-Jan-01. |
| */ |
| |
| #include <common.h> |
| #include <command.h> |
| #include <config.h> |
| #include <net.h> |
| #include <malloc.h> |
| #include <asm/io.h> |
| #include <linux/types.h> |
| #include <usb/mv_udc.h> |
| |
| #if CONFIG_USB_MAX_CONTROLLER_COUNT > 1 |
| #error This driver only supports one single controller. |
| #endif |
| |
| /* |
| * Check if the system has too long cachelines. If the cachelines are |
| * longer then 128b, the driver will not be able flush/invalidate data |
| * cache over separate QH entries. We use 128b because one QH entry is |
| * 64b long and there are always two QH list entries for each endpoint. |
| */ |
| #if ARCH_DMA_MINALIGN > 128 |
| #error This driver can not work on systems with caches longer than 128b |
| #endif |
| |
| #ifndef DEBUG |
| #define DBG(x...) do {} while (0) |
| #else |
| #define DBG(x...) printf(x) |
| static const char *reqname(unsigned r) |
| { |
| switch (r) { |
| case USB_REQ_GET_STATUS: return "GET_STATUS"; |
| case USB_REQ_CLEAR_FEATURE: return "CLEAR_FEATURE"; |
| case USB_REQ_SET_FEATURE: return "SET_FEATURE"; |
| case USB_REQ_SET_ADDRESS: return "SET_ADDRESS"; |
| case USB_REQ_GET_DESCRIPTOR: return "GET_DESCRIPTOR"; |
| case USB_REQ_SET_DESCRIPTOR: return "SET_DESCRIPTOR"; |
| case USB_REQ_GET_CONFIGURATION: return "GET_CONFIGURATION"; |
| case USB_REQ_SET_CONFIGURATION: return "SET_CONFIGURATION"; |
| case USB_REQ_GET_INTERFACE: return "GET_INTERFACE"; |
| case USB_REQ_SET_INTERFACE: return "SET_INTERFACE"; |
| default: return "*UNKNOWN*"; |
| } |
| } |
| #endif |
| |
| static struct usb_endpoint_descriptor ep0_out_desc = { |
| .bLength = sizeof(struct usb_endpoint_descriptor), |
| .bDescriptorType = USB_DT_ENDPOINT, |
| .bEndpointAddress = 0, |
| .bmAttributes = USB_ENDPOINT_XFER_CONTROL, |
| }; |
| |
| static struct usb_endpoint_descriptor ep0_in_desc = { |
| .bLength = sizeof(struct usb_endpoint_descriptor), |
| .bDescriptorType = USB_DT_ENDPOINT, |
| .bEndpointAddress = USB_DIR_IN, |
| .bmAttributes = USB_ENDPOINT_XFER_CONTROL, |
| }; |
| |
| static int mv_pullup(struct usb_gadget *gadget, int is_on); |
| static int mv_ep_enable(struct usb_ep *ep, |
| const struct usb_endpoint_descriptor *desc); |
| static int mv_ep_disable(struct usb_ep *ep); |
| static int mv_ep_queue(struct usb_ep *ep, |
| struct usb_request *req, gfp_t gfp_flags); |
| static struct usb_request * |
| mv_ep_alloc_request(struct usb_ep *ep, unsigned int gfp_flags); |
| static void mv_ep_free_request(struct usb_ep *ep, struct usb_request *_req); |
| |
| static struct usb_gadget_ops mv_udc_ops = { |
| .pullup = mv_pullup, |
| }; |
| |
| static struct usb_ep_ops mv_ep_ops = { |
| .enable = mv_ep_enable, |
| .disable = mv_ep_disable, |
| .queue = mv_ep_queue, |
| .alloc_request = mv_ep_alloc_request, |
| .free_request = mv_ep_free_request, |
| }; |
| |
| /* Init values for USB endpoints. */ |
| static const struct usb_ep mv_ep_init[2] = { |
| [0] = { /* EP 0 */ |
| .maxpacket = 64, |
| .name = "ep0", |
| .ops = &mv_ep_ops, |
| }, |
| [1] = { /* EP 1..n */ |
| .maxpacket = 512, |
| .name = "ep-", |
| .ops = &mv_ep_ops, |
| }, |
| }; |
| |
| static struct mv_drv controller = { |
| .gadget = { |
| .name = "mv_udc", |
| .ops = &mv_udc_ops, |
| .is_dualspeed = 1, |
| }, |
| }; |
| |
| /** |
| * mv_get_qh() - return queue head for endpoint |
| * @ep_num: Endpoint number |
| * @dir_in: Direction of the endpoint (IN = 1, OUT = 0) |
| * |
| * This function returns the QH associated with particular endpoint |
| * and it's direction. |
| */ |
| static struct ept_queue_head *mv_get_qh(int ep_num, int dir_in) |
| { |
| return &controller.epts[(ep_num * 2) + dir_in]; |
| } |
| |
| /** |
| * mv_get_qtd() - return queue item for endpoint |
| * @ep_num: Endpoint number |
| * @dir_in: Direction of the endpoint (IN = 1, OUT = 0) |
| * |
| * This function returns the QH associated with particular endpoint |
| * and it's direction. |
| */ |
| static struct ept_queue_item *mv_get_qtd(int ep_num, int dir_in) |
| { |
| return controller.items[(ep_num * 2) + dir_in]; |
| } |
| |
| /** |
| * mv_flush_qh - flush cache over queue head |
| * @ep_num: Endpoint number |
| * |
| * This function flushes cache over QH for particular endpoint. |
| */ |
| static void mv_flush_qh(int ep_num) |
| { |
| struct ept_queue_head *head = mv_get_qh(ep_num, 0); |
| const uint32_t start = (uint32_t)head; |
| const uint32_t end = start + 2 * sizeof(*head); |
| |
| flush_dcache_range(start, end); |
| } |
| |
| /** |
| * mv_invalidate_qh - invalidate cache over queue head |
| * @ep_num: Endpoint number |
| * |
| * This function invalidates cache over QH for particular endpoint. |
| */ |
| static void mv_invalidate_qh(int ep_num) |
| { |
| struct ept_queue_head *head = mv_get_qh(ep_num, 0); |
| uint32_t start = (uint32_t)head; |
| uint32_t end = start + 2 * sizeof(*head); |
| |
| invalidate_dcache_range(start, end); |
| } |
| |
| /** |
| * mv_flush_qtd - flush cache over queue item |
| * @ep_num: Endpoint number |
| * |
| * This function flushes cache over qTD pair for particular endpoint. |
| */ |
| static void mv_flush_qtd(int ep_num) |
| { |
| struct ept_queue_item *item = mv_get_qtd(ep_num, 0); |
| const uint32_t start = (uint32_t)item; |
| const uint32_t end_raw = start + 2 * sizeof(*item); |
| const uint32_t end = roundup(end_raw, ARCH_DMA_MINALIGN); |
| |
| flush_dcache_range(start, end); |
| } |
| |
| /** |
| * mv_invalidate_qtd - invalidate cache over queue item |
| * @ep_num: Endpoint number |
| * |
| * This function invalidates cache over qTD pair for particular endpoint. |
| */ |
| static void mv_invalidate_qtd(int ep_num) |
| { |
| struct ept_queue_item *item = mv_get_qtd(ep_num, 0); |
| const uint32_t start = (uint32_t)item; |
| const uint32_t end_raw = start + 2 * sizeof(*item); |
| const uint32_t end = roundup(end_raw, ARCH_DMA_MINALIGN); |
| |
| invalidate_dcache_range(start, end); |
| } |
| |
| static struct usb_request * |
| mv_ep_alloc_request(struct usb_ep *ep, unsigned int gfp_flags) |
| { |
| struct mv_ep *mv_ep = container_of(ep, struct mv_ep, ep); |
| return &mv_ep->req; |
| } |
| |
| static void mv_ep_free_request(struct usb_ep *ep, struct usb_request *_req) |
| { |
| return; |
| } |
| |
| static void ep_enable(int num, int in) |
| { |
| struct ept_queue_head *head; |
| struct mv_udc *udc = (struct mv_udc *)controller.ctrl->hcor; |
| unsigned n; |
| head = mv_get_qh(num, in); |
| |
| n = readl(&udc->epctrl[num]); |
| if (in) |
| n |= (CTRL_TXE | CTRL_TXR | CTRL_TXT_BULK); |
| else |
| n |= (CTRL_RXE | CTRL_RXR | CTRL_RXT_BULK); |
| |
| if (num != 0) { |
| head->config = CONFIG_MAX_PKT(EP_MAX_PACKET_SIZE) | CONFIG_ZLT; |
| mv_flush_qh(num); |
| } |
| writel(n, &udc->epctrl[num]); |
| } |
| |
| static int mv_ep_enable(struct usb_ep *ep, |
| const struct usb_endpoint_descriptor *desc) |
| { |
| struct mv_ep *mv_ep = container_of(ep, struct mv_ep, ep); |
| int num, in; |
| num = desc->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK; |
| in = (desc->bEndpointAddress & USB_DIR_IN) != 0; |
| ep_enable(num, in); |
| mv_ep->desc = desc; |
| return 0; |
| } |
| |
| static int mv_ep_disable(struct usb_ep *ep) |
| { |
| struct mv_ep *mv_ep = container_of(ep, struct mv_ep, ep); |
| |
| mv_ep->desc = NULL; |
| return 0; |
| } |
| |
| static int mv_bounce(struct mv_ep *ep) |
| { |
| uint32_t addr = (uint32_t)ep->req.buf; |
| uint32_t ba; |
| |
| /* Input buffer address is not aligned. */ |
| if (addr & (ARCH_DMA_MINALIGN - 1)) |
| goto align; |
| |
| /* Input buffer length is not aligned. */ |
| if (ep->req.length & (ARCH_DMA_MINALIGN - 1)) |
| goto align; |
| |
| /* The buffer is well aligned, only flush cache. */ |
| ep->b_len = ep->req.length; |
| ep->b_buf = ep->req.buf; |
| goto flush; |
| |
| align: |
| /* Use internal buffer for small payloads. */ |
| if (ep->req.length <= 64) { |
| ep->b_len = 64; |
| ep->b_buf = ep->b_fast; |
| } else { |
| ep->b_len = roundup(ep->req.length, ARCH_DMA_MINALIGN); |
| ep->b_buf = memalign(ARCH_DMA_MINALIGN, ep->b_len); |
| if (!ep->b_buf) |
| return -ENOMEM; |
| } |
| |
| memcpy(ep->b_buf, ep->req.buf, ep->req.length); |
| |
| flush: |
| ba = (uint32_t)ep->b_buf; |
| flush_dcache_range(ba, ba + ep->b_len); |
| |
| return 0; |
| } |
| |
| static void mv_debounce(struct mv_ep *ep) |
| { |
| uint32_t addr = (uint32_t)ep->req.buf; |
| uint32_t ba = (uint32_t)ep->b_buf; |
| |
| invalidate_dcache_range(ba, ba + ep->b_len); |
| |
| /* Input buffer address is not aligned. */ |
| if (addr & (ARCH_DMA_MINALIGN - 1)) |
| goto copy; |
| |
| /* Input buffer length is not aligned. */ |
| if (ep->req.length & (ARCH_DMA_MINALIGN - 1)) |
| goto copy; |
| |
| /* The buffer is well aligned, only invalidate cache. */ |
| return; |
| |
| copy: |
| memcpy(ep->req.buf, ep->b_buf, ep->req.length); |
| |
| /* Large payloads use allocated buffer, free it. */ |
| if (ep->req.length > 64) |
| free(ep->b_buf); |
| } |
| |
| static int mv_ep_queue(struct usb_ep *ep, |
| struct usb_request *req, gfp_t gfp_flags) |
| { |
| struct mv_ep *mv_ep = container_of(ep, struct mv_ep, ep); |
| struct mv_udc *udc = (struct mv_udc *)controller.ctrl->hcor; |
| struct ept_queue_item *item; |
| struct ept_queue_head *head; |
| int bit, num, len, in, ret; |
| num = mv_ep->desc->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK; |
| in = (mv_ep->desc->bEndpointAddress & USB_DIR_IN) != 0; |
| item = mv_get_qtd(num, in); |
| head = mv_get_qh(num, in); |
| len = req->length; |
| |
| ret = mv_bounce(mv_ep); |
| if (ret) |
| return ret; |
| |
| item->next = TERMINATE; |
| item->info = INFO_BYTES(len) | INFO_IOC | INFO_ACTIVE; |
| item->page0 = (uint32_t)mv_ep->b_buf; |
| item->page1 = ((uint32_t)mv_ep->b_buf & 0xfffff000) + 0x1000; |
| mv_flush_qtd(num); |
| |
| head->next = (unsigned) item; |
| head->info = 0; |
| |
| DBG("ept%d %s queue len %x, buffer %p\n", |
| num, in ? "in" : "out", len, mv_ep->b_buf); |
| mv_flush_qh(num); |
| |
| if (in) |
| bit = EPT_TX(num); |
| else |
| bit = EPT_RX(num); |
| |
| writel(bit, &udc->epprime); |
| |
| return 0; |
| } |
| |
| static void handle_ep_complete(struct mv_ep *ep) |
| { |
| struct ept_queue_item *item; |
| int num, in, len; |
| num = ep->desc->bEndpointAddress & USB_ENDPOINT_NUMBER_MASK; |
| in = (ep->desc->bEndpointAddress & USB_DIR_IN) != 0; |
| if (num == 0) |
| ep->desc = &ep0_out_desc; |
| item = mv_get_qtd(num, in); |
| mv_invalidate_qtd(num); |
| |
| if (item->info & 0xff) |
| printf("EP%d/%s FAIL info=%x pg0=%x\n", |
| num, in ? "in" : "out", item->info, item->page0); |
| |
| len = (item->info >> 16) & 0x7fff; |
| |
| mv_debounce(ep); |
| |
| ep->req.length -= len; |
| DBG("ept%d %s complete %x\n", |
| num, in ? "in" : "out", len); |
| ep->req.complete(&ep->ep, &ep->req); |
| if (num == 0) { |
| ep->req.length = 0; |
| usb_ep_queue(&ep->ep, &ep->req, 0); |
| ep->desc = &ep0_in_desc; |
| } |
| } |
| |
| #define SETUP(type, request) (((type) << 8) | (request)) |
| |
| static void handle_setup(void) |
| { |
| struct usb_request *req = &controller.ep[0].req; |
| struct mv_udc *udc = (struct mv_udc *)controller.ctrl->hcor; |
| struct ept_queue_head *head; |
| struct usb_ctrlrequest r; |
| int status = 0; |
| int num, in, _num, _in, i; |
| char *buf; |
| head = mv_get_qh(0, 0); /* EP0 OUT */ |
| |
| mv_invalidate_qh(0); |
| memcpy(&r, head->setup_data, sizeof(struct usb_ctrlrequest)); |
| writel(EPT_RX(0), &udc->epstat); |
| DBG("handle setup %s, %x, %x index %x value %x\n", reqname(r.bRequest), |
| r.bRequestType, r.bRequest, r.wIndex, r.wValue); |
| |
| switch (SETUP(r.bRequestType, r.bRequest)) { |
| case SETUP(USB_RECIP_ENDPOINT, USB_REQ_CLEAR_FEATURE): |
| _num = r.wIndex & 15; |
| _in = !!(r.wIndex & 0x80); |
| |
| if ((r.wValue == 0) && (r.wLength == 0)) { |
| req->length = 0; |
| for (i = 0; i < NUM_ENDPOINTS; i++) { |
| if (!controller.ep[i].desc) |
| continue; |
| num = controller.ep[i].desc->bEndpointAddress |
| & USB_ENDPOINT_NUMBER_MASK; |
| in = (controller.ep[i].desc->bEndpointAddress |
| & USB_DIR_IN) != 0; |
| if ((num == _num) && (in == _in)) { |
| ep_enable(num, in); |
| usb_ep_queue(controller.gadget.ep0, |
| req, 0); |
| break; |
| } |
| } |
| } |
| return; |
| |
| case SETUP(USB_RECIP_DEVICE, USB_REQ_SET_ADDRESS): |
| /* |
| * write address delayed (will take effect |
| * after the next IN txn) |
| */ |
| writel((r.wValue << 25) | (1 << 24), &udc->devaddr); |
| req->length = 0; |
| usb_ep_queue(controller.gadget.ep0, req, 0); |
| return; |
| |
| case SETUP(USB_DIR_IN | USB_RECIP_DEVICE, USB_REQ_GET_STATUS): |
| req->length = 2; |
| buf = (char *)req->buf; |
| buf[0] = 1 << USB_DEVICE_SELF_POWERED; |
| buf[1] = 0; |
| usb_ep_queue(controller.gadget.ep0, req, 0); |
| return; |
| } |
| /* pass request up to the gadget driver */ |
| if (controller.driver) |
| status = controller.driver->setup(&controller.gadget, &r); |
| else |
| status = -ENODEV; |
| |
| if (!status) |
| return; |
| DBG("STALL reqname %s type %x value %x, index %x\n", |
| reqname(r.bRequest), r.bRequestType, r.wValue, r.wIndex); |
| writel((1<<16) | (1 << 0), &udc->epctrl[0]); |
| } |
| |
| static void stop_activity(void) |
| { |
| int i, num, in; |
| struct ept_queue_head *head; |
| struct mv_udc *udc = (struct mv_udc *)controller.ctrl->hcor; |
| writel(readl(&udc->epcomp), &udc->epcomp); |
| writel(readl(&udc->epstat), &udc->epstat); |
| writel(0xffffffff, &udc->epflush); |
| |
| /* error out any pending reqs */ |
| for (i = 0; i < NUM_ENDPOINTS; i++) { |
| if (i != 0) |
| writel(0, &udc->epctrl[i]); |
| if (controller.ep[i].desc) { |
| num = controller.ep[i].desc->bEndpointAddress |
| & USB_ENDPOINT_NUMBER_MASK; |
| in = (controller.ep[i].desc->bEndpointAddress |
| & USB_DIR_IN) != 0; |
| head = mv_get_qh(num, in); |
| head->info = INFO_ACTIVE; |
| mv_flush_qh(num); |
| } |
| } |
| } |
| |
| void udc_irq(void) |
| { |
| struct mv_udc *udc = (struct mv_udc *)controller.ctrl->hcor; |
| unsigned n = readl(&udc->usbsts); |
| writel(n, &udc->usbsts); |
| int bit, i, num, in; |
| |
| n &= (STS_SLI | STS_URI | STS_PCI | STS_UI | STS_UEI); |
| if (n == 0) |
| return; |
| |
| if (n & STS_URI) { |
| DBG("-- reset --\n"); |
| stop_activity(); |
| } |
| if (n & STS_SLI) |
| DBG("-- suspend --\n"); |
| |
| if (n & STS_PCI) { |
| DBG("-- portchange --\n"); |
| bit = (readl(&udc->portsc) >> 26) & 3; |
| if (bit == 2) { |
| controller.gadget.speed = USB_SPEED_HIGH; |
| for (i = 1; i < NUM_ENDPOINTS && n; i++) |
| if (controller.ep[i].desc) |
| controller.ep[i].ep.maxpacket = 512; |
| } else { |
| controller.gadget.speed = USB_SPEED_FULL; |
| } |
| } |
| |
| if (n & STS_UEI) |
| printf("<UEI %x>\n", readl(&udc->epcomp)); |
| |
| if ((n & STS_UI) || (n & STS_UEI)) { |
| n = readl(&udc->epstat); |
| if (n & EPT_RX(0)) |
| handle_setup(); |
| |
| n = readl(&udc->epcomp); |
| if (n != 0) |
| writel(n, &udc->epcomp); |
| |
| for (i = 0; i < NUM_ENDPOINTS && n; i++) { |
| if (controller.ep[i].desc) { |
| num = controller.ep[i].desc->bEndpointAddress |
| & USB_ENDPOINT_NUMBER_MASK; |
| in = (controller.ep[i].desc->bEndpointAddress |
| & USB_DIR_IN) != 0; |
| bit = (in) ? EPT_TX(num) : EPT_RX(num); |
| if (n & bit) |
| handle_ep_complete(&controller.ep[i]); |
| } |
| } |
| } |
| } |
| |
| int usb_gadget_handle_interrupts(void) |
| { |
| u32 value; |
| struct mv_udc *udc = (struct mv_udc *)controller.ctrl->hcor; |
| |
| value = readl(&udc->usbsts); |
| if (value) |
| udc_irq(); |
| |
| return value; |
| } |
| |
| static int mv_pullup(struct usb_gadget *gadget, int is_on) |
| { |
| struct mv_udc *udc = (struct mv_udc *)controller.ctrl->hcor; |
| if (is_on) { |
| /* RESET */ |
| writel(USBCMD_ITC(MICRO_8FRAME) | USBCMD_RST, &udc->usbcmd); |
| udelay(200); |
| |
| writel((unsigned)controller.epts, &udc->epinitaddr); |
| |
| /* select DEVICE mode */ |
| writel(USBMODE_DEVICE, &udc->usbmode); |
| |
| writel(0xffffffff, &udc->epflush); |
| |
| /* Turn on the USB connection by enabling the pullup resistor */ |
| writel(USBCMD_ITC(MICRO_8FRAME) | USBCMD_RUN, &udc->usbcmd); |
| } else { |
| stop_activity(); |
| writel(USBCMD_FS2, &udc->usbcmd); |
| udelay(800); |
| if (controller.driver) |
| controller.driver->disconnect(gadget); |
| } |
| |
| return 0; |
| } |
| |
| void udc_disconnect(void) |
| { |
| struct mv_udc *udc = (struct mv_udc *)controller.ctrl->hcor; |
| /* disable pullup */ |
| stop_activity(); |
| writel(USBCMD_FS2, &udc->usbcmd); |
| udelay(800); |
| if (controller.driver) |
| controller.driver->disconnect(&controller.gadget); |
| } |
| |
| static int mvudc_probe(void) |
| { |
| struct ept_queue_head *head; |
| uint8_t *imem; |
| int i; |
| |
| const int num = 2 * NUM_ENDPOINTS; |
| |
| const int eplist_min_align = 4096; |
| const int eplist_align = roundup(eplist_min_align, ARCH_DMA_MINALIGN); |
| const int eplist_raw_sz = num * sizeof(struct ept_queue_head); |
| const int eplist_sz = roundup(eplist_raw_sz, ARCH_DMA_MINALIGN); |
| |
| const int ilist_align = roundup(ARCH_DMA_MINALIGN, 32); |
| const int ilist_ent_raw_sz = 2 * sizeof(struct ept_queue_item); |
| const int ilist_ent_sz = roundup(ilist_ent_raw_sz, ARCH_DMA_MINALIGN); |
| const int ilist_sz = NUM_ENDPOINTS * ilist_ent_sz; |
| |
| /* The QH list must be aligned to 4096 bytes. */ |
| controller.epts = memalign(eplist_align, eplist_sz); |
| if (!controller.epts) |
| return -ENOMEM; |
| memset(controller.epts, 0, eplist_sz); |
| |
| /* |
| * Each qTD item must be 32-byte aligned, each qTD touple must be |
| * cacheline aligned. There are two qTD items for each endpoint and |
| * only one of them is used for the endpoint at time, so we can group |
| * them together. |
| */ |
| controller.items_mem = memalign(ilist_align, ilist_sz); |
| if (!controller.items_mem) { |
| free(controller.epts); |
| return -ENOMEM; |
| } |
| memset(controller.items_mem, 0, ilist_sz); |
| |
| for (i = 0; i < 2 * NUM_ENDPOINTS; i++) { |
| /* |
| * Configure QH for each endpoint. The structure of the QH list |
| * is such that each two subsequent fields, N and N+1 where N is |
| * even, in the QH list represent QH for one endpoint. The Nth |
| * entry represents OUT configuration and the N+1th entry does |
| * represent IN configuration of the endpoint. |
| */ |
| head = controller.epts + i; |
| if (i < 2) |
| head->config = CONFIG_MAX_PKT(EP0_MAX_PACKET_SIZE) |
| | CONFIG_ZLT | CONFIG_IOS; |
| else |
| head->config = CONFIG_MAX_PKT(EP_MAX_PACKET_SIZE) |
| | CONFIG_ZLT; |
| head->next = TERMINATE; |
| head->info = 0; |
| |
| imem = controller.items_mem + ((i >> 1) * ilist_ent_sz); |
| if (i & 1) |
| imem += sizeof(struct ept_queue_item); |
| |
| controller.items[i] = (struct ept_queue_item *)imem; |
| |
| if (i & 1) { |
| mv_flush_qh(i - 1); |
| mv_flush_qtd(i - 1); |
| } |
| } |
| |
| INIT_LIST_HEAD(&controller.gadget.ep_list); |
| |
| /* Init EP 0 */ |
| memcpy(&controller.ep[0].ep, &mv_ep_init[0], sizeof(*mv_ep_init)); |
| controller.ep[0].desc = &ep0_in_desc; |
| controller.gadget.ep0 = &controller.ep[0].ep; |
| INIT_LIST_HEAD(&controller.gadget.ep0->ep_list); |
| |
| /* Init EP 1..n */ |
| for (i = 1; i < NUM_ENDPOINTS; i++) { |
| memcpy(&controller.ep[i].ep, &mv_ep_init[1], |
| sizeof(*mv_ep_init)); |
| list_add_tail(&controller.ep[i].ep.ep_list, |
| &controller.gadget.ep_list); |
| } |
| |
| return 0; |
| } |
| |
| int usb_gadget_register_driver(struct usb_gadget_driver *driver) |
| { |
| struct mv_udc *udc; |
| int ret; |
| |
| if (!driver) |
| return -EINVAL; |
| if (!driver->bind || !driver->setup || !driver->disconnect) |
| return -EINVAL; |
| if (driver->speed != USB_SPEED_FULL && driver->speed != USB_SPEED_HIGH) |
| return -EINVAL; |
| |
| ret = usb_lowlevel_init(0, (void **)&controller.ctrl); |
| if (ret) |
| return ret; |
| |
| ret = mvudc_probe(); |
| if (!ret) { |
| udc = (struct mv_udc *)controller.ctrl->hcor; |
| |
| /* select ULPI phy */ |
| writel(PTS(PTS_ENABLE) | PFSC, &udc->portsc); |
| } |
| |
| ret = driver->bind(&controller.gadget); |
| if (ret) { |
| DBG("driver->bind() returned %d\n", ret); |
| return ret; |
| } |
| controller.driver = driver; |
| |
| return 0; |
| } |
| |
| int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) |
| { |
| return 0; |
| } |