blob: 61137bcbf1c5c2e482aa9c7f48903592a2ac40e7 [file] [log] [blame]
.. SPDX-License-Identifier: GPL-2.0+
.. Copyright (C) 2018, Bin Meng <bmeng.cn@gmail.com>
QEMU RISC-V
===========
QEMU for RISC-V supports a special 'virt' machine and 'spike' machine designed
for emulation and virtualization purposes. This document describes how to run
U-Boot under it. Both 32-bit and 64-bit targets are supported, running in
either machine or supervisor mode.
The QEMU virt machine models a generic RISC-V virtual machine with support for
the VirtIO standard networking and block storage devices. It has CLINT, PLIC,
16550A UART devices in addition to VirtIO and it also uses device-tree to pass
configuration information to guest software. It implements the latest RISC-V
privileged architecture.
See :doc:`../../develop/devicetree/dt_qemu` for information on how to see
the devicetree actually generated by QEMU.
The QEMU spike machine models a minimalistic RISC-V virtual machine with
only CLINT and HTIF devices. It also uses device-tree to pass configuration
information to guest software and implements the latest RISC-V privileged
architecture.
Building U-Boot
---------------
Set the CROSS_COMPILE environment variable as usual, and run:
- For 32-bit RISC-V::
make qemu-riscv32_defconfig
make
- For 64-bit RISC-V::
make qemu-riscv64_defconfig
make
This will compile U-Boot for machine mode. To build supervisor mode binaries,
use the configurations qemu-riscv32_smode_defconfig and
qemu-riscv64_smode_defconfig instead. Note that U-Boot running in supervisor
mode requires a supervisor binary interface (SBI), such as RISC-V OpenSBI.
Running U-Boot
--------------
The minimal QEMU command line to get U-Boot up and running is:
- For 32-bit RISC-V virt machine::
qemu-system-riscv32 -nographic -machine virt -bios u-boot.bin
- For 64-bit RISC-V virt machine::
qemu-system-riscv64 -nographic -machine virt -bios u-boot.bin
- For 64-bit RISC-V spike machine::
qemu-system-riscv64 -nographic -machine spike -bios u-boot.bin
The commands above create targets with 128MiB memory by default.
A freely configurable amount of RAM can be created via the '-m'
parameter. For example, '-m 2G' creates 2GiB memory for the target,
and the memory node in the embedded DTB created by QEMU reflects
the new setting.
For instructions on how to run U-Boot in supervisor mode on QEMU
with OpenSBI, see the documentation available with OpenSBI:
https://github.com/riscv/opensbi/blob/master/docs/platform/qemu_virt.md
https://github.com/riscv/opensbi/blob/master/docs/platform/spike.md
These have been tested in QEMU 5.0.0.
Running U-Boot SPL
------------------
In the default SPL configuration, U-Boot SPL starts in machine mode. U-Boot
proper and OpenSBI (FW_DYNAMIC firmware) are bundled as FIT image and made
available to U-Boot SPL. Both are then loaded by U-Boot SPL and the location
of U-Boot proper is passed to OpenSBI. After initialization, U-Boot proper is
started in supervisor mode by OpenSBI.
OpenSBI must be compiled before compiling U-Boot. Version 0.4 and higher is
supported by U-Boot. Clone the OpenSBI repository and run the following command.
.. code-block:: console
git clone https://github.com/riscv/opensbi.git
cd opensbi
make PLATFORM=generic
See the OpenSBI documentation for full details:
https://github.com/riscv/opensbi/blob/master/docs/platform/qemu_virt.md
https://github.com/riscv/opensbi/blob/master/docs/platform/spike.md
To make the FW_DYNAMIC binary (build/platform/generic/firmware/fw_dynamic.bin)
available to U-Boot, either copy it into the U-Boot root directory or specify
its location with the OPENSBI environment variable. Afterwards, compile U-Boot
with the following commands.
- For 32-bit RISC-V::
make qemu-riscv32_spl_defconfig
make
- For 64-bit RISC-V::
make qemu-riscv64_spl_defconfig
make
The minimal QEMU commands to run U-Boot SPL in both 32-bit and 64-bit
configurations are:
- For 32-bit RISC-V virt machine::
qemu-system-riscv32 -nographic -machine virt -bios spl/u-boot-spl.bin \
-device loader,file=u-boot.itb,addr=0x80200000
- For 64-bit RISC-V virt machine::
qemu-system-riscv64 -nographic -machine virt -bios spl/u-boot-spl.bin \
-device loader,file=u-boot.itb,addr=0x80200000
- For 64-bit RISC-V spike machine::
qemu-system-riscv64 -nographic -machine spike -bios spl/u-boot-spl.bin \
-device loader,file=u-boot.itb,addr=0x80200000
An attached disk can be emulated in RISC-V virt machine by adding::
-device ich9-ahci,id=ahci \
-drive if=none,file=riscv64.img,format=raw,id=mydisk \
-device ide-hd,drive=mydisk,bus=ahci.0
You will have to run 'scsi scan' to use it.
A video console can be emulated in RISC-V virt machine by removing "-nographic"
and adding::
-serial stdio -device VGA
In addition, a usb keyboard can be attached to an emulated xHCI controller in
RISC-V virt machine as an option of input devices by adding::
-device qemu-xhci,id=xhci -device usb-kbd,bus=xhci.0
Running with KVM
----------------
Running with QEMU using KVM requires an S-mode U-Boot binary as created by
qemu-riscv64_smode_defconfig.
Provide the U-Boot S-mode ELF image as *-kernel* parameter and do not add a
*-bios* parameter, e.g.
.. code-block:: bash
qemu-system-riscv64 -accel kvm -nographic -machine virt -kernel u-boot
Debug UART
----------
The following settings provide a debug UART for the virt machine::
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_NS16550=y
CONFIG_DEBUG_UART_BASE=0x10000000
CONFIG_DEBUG_UART_CLOCK=3686400