blob: a3b20b8f9584ef0623dfd16e30c0d2901f441040 [file] [log] [blame]
/*
* Copyright (C) 2007 Freescale Semiconductor, Inc.
* Kevin Lam <kevin.lam@freescale.com>
* Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*/
#include <common.h>
#include <i2c.h>
#include <asm/io.h>
#include <spd_sdram.h>
#include <vsc7385.h>
#if defined(CFG_DRAM_TEST)
int
testdram(void)
{
uint *pstart = (uint *) CFG_MEMTEST_START;
uint *pend = (uint *) CFG_MEMTEST_END;
uint *p;
printf("Testing DRAM from 0x%08x to 0x%08x\n",
CFG_MEMTEST_START,
CFG_MEMTEST_END);
printf("DRAM test phase 1:\n");
for (p = pstart; p < pend; p++)
*p = 0xaaaaaaaa;
for (p = pstart; p < pend; p++) {
if (*p != 0xaaaaaaaa) {
printf("DRAM test fails at: %08x\n", (uint) p);
return 1;
}
}
printf("DRAM test phase 2:\n");
for (p = pstart; p < pend; p++)
*p = 0x55555555;
for (p = pstart; p < pend; p++) {
if (*p != 0x55555555) {
printf("DRAM test fails at: %08x\n", (uint) p);
return 1;
}
}
printf("DRAM test passed.\n");
return 0;
}
#endif
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
void ddr_enable_ecc(unsigned int dram_size);
#endif
int fixed_sdram(void);
long int initdram(int board_type)
{
immap_t *im = (immap_t *) CFG_IMMR;
u32 msize = 0;
if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32) im)
return -1;
#if defined(CONFIG_SPD_EEPROM)
msize = spd_sdram();
#else
msize = fixed_sdram();
#endif
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRC)
/* Initialize DDR ECC byte */
ddr_enable_ecc(msize * 1024 * 1024);
#endif
/* return total bus DDR size(bytes) */
return (msize * 1024 * 1024);
}
#if !defined(CONFIG_SPD_EEPROM)
/*************************************************************************
* fixed sdram init -- doesn't use serial presence detect.
************************************************************************/
int fixed_sdram(void)
{
immap_t *im = (immap_t *) CFG_IMMR;
u32 msize = CFG_DDR_SIZE * 1024 * 1024;
u32 msize_log2 = __ilog2(msize);
im->sysconf.ddrlaw[0].bar = CFG_DDR_SDRAM_BASE >> 12;
im->sysconf.ddrlaw[0].ar = LBLAWAR_EN | (msize_log2 - 1);
im->sysconf.ddrcdr = CFG_DDRCDR_VALUE;
udelay(50000);
im->ddr.sdram_clk_cntl = CFG_DDR_SDRAM_CLK_CNTL;
udelay(1000);
im->ddr.csbnds[0].csbnds = CFG_DDR_CS0_BNDS;
im->ddr.cs_config[0] = CFG_DDR_CS0_CONFIG;
udelay(1000);
im->ddr.timing_cfg_0 = CFG_DDR_TIMING_0;
im->ddr.timing_cfg_1 = CFG_DDR_TIMING_1;
im->ddr.timing_cfg_2 = CFG_DDR_TIMING_2;
im->ddr.timing_cfg_3 = CFG_DDR_TIMING_3;
im->ddr.sdram_cfg = CFG_DDR_SDRAM_CFG;
im->ddr.sdram_cfg2 = CFG_DDR_SDRAM_CFG2;
im->ddr.sdram_mode = CFG_DDR_MODE;
im->ddr.sdram_mode2 = CFG_DDR_MODE2;
im->ddr.sdram_interval = CFG_DDR_INTERVAL;
sync();
udelay(1000);
im->ddr.sdram_cfg |= SDRAM_CFG_MEM_EN;
udelay(2000);
return CFG_DDR_SIZE;
}
#endif /*!CFG_SPD_EEPROM */
int checkboard(void)
{
puts("Board: Freescale MPC837xERDB\n");
return 0;
}
/*
* Miscellaneous late-boot configurations
*
* If a VSC7385 microcode image is present, then upload it.
*/
int misc_init_r(void)
{
int rc = 0;
#ifdef CONFIG_VSC7385_IMAGE
if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
CONFIG_VSC7385_IMAGE_SIZE)) {
puts("Failure uploading VSC7385 microcode.\n");
rc = 1;
}
#endif
return rc;
}
#if defined(CONFIG_OF_BOARD_SETUP)
void ft_board_setup(void *blob, bd_t *bd)
{
#ifdef CONFIG_PCI
ft_pci_setup(blob, bd);
#endif
ft_cpu_setup(blob, bd);
}
#endif /* CONFIG_OF_BOARD_SETUP */