| /* |
| * (C) Copyright 2001 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_MPC860 1 /* This is a MPC860 CPU */ |
| #define CONFIG_IVML24 1 /* ...on a IVML24 board */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0xFF000000 |
| |
| #if defined (CONFIG_IVML24_16M) |
| # define CONFIG_IDENT_STRING " IVML24" |
| #elif defined (CONFIG_IVML24_32M) |
| # define CONFIG_IDENT_STRING " IVML24_128" |
| #elif defined (CONFIG_IVML24_64M) |
| # define CONFIG_IDENT_STRING " IVML24_256" |
| #endif |
| |
| #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ |
| #undef CONFIG_8xx_CONS_SMC2 |
| #undef CONFIG_8xx_CONS_NONE |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ |
| #define CONFIG_8xx_GCLK_FREQ 50331648 |
| |
| #define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ |
| |
| #define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */ |
| |
| #if 0 |
| #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ |
| #else |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| #endif |
| #define CONFIG_BOOTCOMMAND "bootp" /* autoboot command */ |
| |
| #define CONFIG_BOOTARGS "root=/dev/nfs rw " \ |
| "nfsroot=10.0.0.2:/opt/eldk/ppc_8xx " \ |
| "nfsaddrs=10.0.0.99:10.0.0.2" |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| #define CONFIG_STATUS_LED 1 /* Status LED enabled */ |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_IDE |
| |
| |
| #define CONFIG_MAC_PARTITION |
| #define CONFIG_DOS_PARTITION |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_SUBNETMASK |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */ |
| |
| #define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ |
| |
| #define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ |
| |
| #define CONFIG_SYS_PB_12V_ENABLE 0x00002000 /* PB 18 */ |
| #define CONFIG_SYS_PB_ILOCK_SWITCH 0x00004000 /* PB 17 */ |
| #define CONFIG_SYS_PB_SDRAM_CLKE 0x00008000 /* PB 16 */ |
| #define CONFIG_SYS_PB_ETH_POWERDOWN 0x00010000 /* PB 15 */ |
| #define CONFIG_SYS_PB_IDE_MOTOR 0x00020000 /* PB 14 */ |
| |
| #define CONFIG_SYS_PC_ETH_RESET ((ushort)0x0010) /* PC 11 */ |
| #define CONFIG_SYS_PC_IDE_RESET ((ushort)0x0020) /* PC 10 */ |
| |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| */ |
| /*----------------------------------------------------------------------- |
| * Internal Memory Mapped Register |
| */ |
| #define CONFIG_SYS_IMMR 0xFFF00000 /* was: 0xFF000000 */ |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in DPRAM) |
| */ |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR |
| |
| #if defined (CONFIG_IVML24_16M) |
| # define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ |
| #elif defined (CONFIG_IVML24_32M) |
| # define CONFIG_SYS_INIT_RAM_SIZE 0x3000 /* Size of used area in DPRAM */ |
| #elif defined (CONFIG_IVML24_64M) |
| # define CONFIG_SYS_INIT_RAM_SIZE 0x3000 /* Size of used area in DPRAM */ |
| #endif |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| #define CONFIG_SYS_FLASH_BASE 0xFF000000 |
| #ifdef DEBUG |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| #else |
| #define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ |
| #endif |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_OFFSET 0x7A000 /* Offset of Environment Sector */ |
| #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SYPCR - System Protection Control 11-9 |
| * SYPCR can only be written once after reset! |
| *----------------------------------------------------------------------- |
| * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze |
| */ |
| #if defined(CONFIG_WATCHDOG) |
| |
| # if defined (CONFIG_IVML24_16M) |
| # define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
| SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) |
| # elif defined (CONFIG_IVML24_32M) |
| # define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
| SYPCR_SWE | SYPCR_SWP) |
| # elif defined (CONFIG_IVML24_64M) |
| # define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
| SYPCR_SWE | SYPCR_SWP) |
| # endif |
| |
| #else |
| #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * SIUMCR - SIU Module Configuration 11-6 |
| *----------------------------------------------------------------------- |
| * PCMCIA config., multi-function pin tri-state |
| */ |
| /* EARB, DBGC and DBPC are initialised by the HCW */ |
| /* => 0x000000C0 */ |
| #define CONFIG_SYS_SIUMCR (SIUMCR_BSC | SIUMCR_GB5E) |
| |
| /*----------------------------------------------------------------------- |
| * TBSCR - Time Base Status and Control 11-26 |
| *----------------------------------------------------------------------- |
| * Clear Reference Interrupt Status, Timebase freezing enabled |
| */ |
| #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) |
| |
| /*----------------------------------------------------------------------- |
| * PISCR - Periodic Interrupt Status and Control 11-31 |
| *----------------------------------------------------------------------- |
| * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled |
| */ |
| #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) |
| |
| /*----------------------------------------------------------------------- |
| * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 |
| *----------------------------------------------------------------------- |
| * Reset PLL lock status sticky bit, timer expired status bit and timer |
| * interrupt status bit, set PLL multiplication factor ! |
| */ |
| /* 0x00B0C0C0 */ |
| #define CONFIG_SYS_PLPRCR \ |
| ( (11 << PLPRCR_MF_SHIFT) | \ |
| PLPRCR_SPLSS | PLPRCR_TEXPS | /*PLPRCR_TMIST|*/ \ |
| /*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL | \ |
| PLPRCR_CSR | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/ \ |
| ) |
| |
| /*----------------------------------------------------------------------- |
| * SCCR - System Clock and reset Control Register 15-27 |
| *----------------------------------------------------------------------- |
| * Set clock output, timebase and RTC source and divider, |
| * power management and some other internal clocks |
| */ |
| #define SCCR_MASK SCCR_EBDF11 |
| /* 0x01800014 */ |
| #define CONFIG_SYS_SCCR (SCCR_COM01 | /*SCCR_TBS|*/ \ |
| SCCR_RTDIV | SCCR_RTSEL | \ |
| /*SCCR_CRQEN|*/ /*SCCR_PRQEN|*/ \ |
| SCCR_EBDF00 | SCCR_DFSYNC00 | \ |
| SCCR_DFBRG00 | SCCR_DFNL000 | \ |
| SCCR_DFNH000 | SCCR_DFLCD101 | \ |
| SCCR_DFALCD00) |
| |
| /*----------------------------------------------------------------------- |
| * RTCSC - Real-Time Clock Status and Control Register 11-27 |
| *----------------------------------------------------------------------- |
| */ |
| /* 0x00C3 */ |
| #define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) |
| |
| |
| /*----------------------------------------------------------------------- |
| * RCCR - RISC Controller Configuration Register 19-4 |
| *----------------------------------------------------------------------- |
| */ |
| /* TIMEP=2 */ |
| #define CONFIG_SYS_RCCR 0x0200 |
| |
| /*----------------------------------------------------------------------- |
| * RMDS - RISC Microcode Development Support Control Register |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_SYS_RMDS 0 |
| |
| /*----------------------------------------------------------------------- |
| * |
| * Interrupt Levels |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_SYS_CPM_INTERRUPT 13 /* SIU_LEVEL6 */ |
| |
| /*----------------------------------------------------------------------- |
| * PCMCIA stuff |
| *----------------------------------------------------------------------- |
| * |
| */ |
| #define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) |
| #define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) |
| #define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) |
| #define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) |
| #define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) |
| #define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) |
| |
| /*----------------------------------------------------------------------- |
| * IDE/ATA stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */ |
| #define CONFIG_IDE_INIT_POSTRESET 1 /* Use postreset IDE hook */ |
| #define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */ |
| #define CONFIG_IDE_RESET 1 /* reset for ide supported */ |
| |
| #define CONFIG_SYS_IDE_MAXBUS 1 /* The IVML24 has only 1 IDE bus*/ |
| #define CONFIG_SYS_IDE_MAXDEVICE 1 /* ... and only 1 IDE device */ |
| |
| #define CONFIG_SYS_ATA_BASE_ADDR 0xFE100000 |
| #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 |
| #undef CONFIG_SYS_ATA_IDE1_OFFSET /* only one IDE bus available */ |
| |
| #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */ |
| #define CONFIG_SYS_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */ |
| #define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */ |
| |
| /*----------------------------------------------------------------------- |
| * |
| *----------------------------------------------------------------------- |
| * |
| */ |
| #define CONFIG_SYS_DER 0 |
| |
| /* |
| * Init Memory Controller: |
| * |
| * BR0 and OR0 (FLASH) |
| */ |
| |
| #define FLASH_BASE0_PRELIM 0xFF000000 /* FLASH bank #0 */ |
| |
| /* used to re-map FLASH both when starting from SRAM or FLASH: |
| * restrict access enough to keep SRAM working (if any) |
| * but not too much to meddle with FLASH accesses |
| */ |
| /* EPROMs are 512kb */ |
| #define CONFIG_SYS_REMAP_OR_AM 0xFFF80000 /* OR addr mask */ |
| #define CONFIG_SYS_PRELIM_OR_AM 0xFFF80000 /* OR addr mask */ |
| |
| /* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ |
| #define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_5_CLK | OR_EHTR) |
| |
| #define CONFIG_SYS_OR0_REMAP ( CONFIG_SYS_REMAP_OR_AM | OR_ACS_DIV4 | OR_BI | \ |
| CONFIG_SYS_OR_TIMING_FLASH) |
| #define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | OR_ACS_DIV4 | OR_BI | \ |
| CONFIG_SYS_OR_TIMING_FLASH) |
| /* 16 bit, bank valid */ |
| #define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V ) |
| |
| /* |
| * BR1/OR1 - ELIC SACCO bank @ 0xFE000000 |
| * |
| * AM=0xFFFF8 ATM=0 CSNT/SAM=1 ACS/G5LA/G5LS=3 BIH=1 SCY=2 SETA=0 TRLX=1 EHTR=1 |
| */ |
| #define ELIC_SACCO_BASE 0xFE000000 |
| #define ELIC_SACCO_OR_AM 0xFFFF8000 |
| #define ELIC_SACCO_TIMING (OR_SCY_2_CLK | OR_TRLX | OR_EHTR) |
| |
| #define CONFIG_SYS_OR1 (ELIC_SACCO_OR_AM | OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \ |
| ELIC_SACCO_TIMING) |
| #define CONFIG_SYS_BR1 ((ELIC_SACCO_BASE & BR_BA_MSK) | BR_PS_8 | BR_V ) |
| |
| /* |
| * BR2/OR2 - ELIC EPIC bank @ 0xFE008000 |
| * |
| * AM=0xFFFF8 ATM=0 CSNT/SAM=1 ACS/G5LA/G5LS=3 BIH=1 SCY=2 SETA=0 TRLX=1 EHTR=1 |
| */ |
| #define ELIC_EPIC_BASE 0xFE008000 |
| #define ELIC_EPIC_OR_AM 0xFFFF8000 |
| #define ELIC_EPIC_TIMING (OR_SCY_2_CLK | OR_TRLX | OR_EHTR) |
| |
| #define CONFIG_SYS_OR2 (ELIC_EPIC_OR_AM | OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \ |
| ELIC_EPIC_TIMING) |
| #define CONFIG_SYS_BR2 ((ELIC_EPIC_BASE & BR_BA_MSK) | BR_PS_8 | BR_V ) |
| |
| /* |
| * BR3/OR3: SDRAM |
| * |
| * Multiplexed addresses, GPL5 output to GPL5_A (don't care) |
| */ |
| #define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */ |
| #define SDRAM_PRELIM_OR_AM 0xF8000000 /* map max. 128 MB */ |
| #define SDRAM_TIMING OR_SCY_0_CLK /* SDRAM-Timing */ |
| |
| #define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB SDRAM */ |
| |
| #define CONFIG_SYS_OR3_PRELIM (SDRAM_PRELIM_OR_AM | OR_CSNT_SAM | OR_G5LS | SDRAM_TIMING ) |
| #define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_V ) |
| |
| /* |
| * BR4/OR4 - HDLC Address |
| * |
| * AM=0xFFFF8 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=0 BIH=1 SCY=1 SETA=0 TRLX=0 EHTR=0 |
| */ |
| #define HDLC_ADDR_BASE 0xFE108000 /* HDLC Address area */ |
| #define HDLC_ADDR_OR_AM 0xFFFF8000 |
| #define HDLC_ADDR_TIMING OR_SCY_1_CLK |
| |
| #define CONFIG_SYS_OR4 (HDLC_ADDR_OR_AM | OR_BI | HDLC_ADDR_TIMING) |
| #define CONFIG_SYS_BR4 ((HDLC_ADDR_BASE & BR_BA_MSK) | BR_PS_8 | BR_WP | BR_V ) |
| |
| /* |
| * BR5/OR5: SHARC ADSP-2165L |
| * |
| * AM=0xFFC00 ATM=0 CSNT/SAM=0 ACS/G5LA/G5LS=3 BIH=1 SCY=0 SETA=0 TRLX=0 EHTR=0 |
| */ |
| #define SHARC_BASE 0xFE400000 |
| #define SHARC_OR_AM 0xFFC00000 |
| #define SHARC_TIMING OR_SCY_0_CLK |
| |
| #define CONFIG_SYS_OR5 (SHARC_OR_AM | OR_ACS_DIV2 | OR_BI | SHARC_TIMING ) |
| #define CONFIG_SYS_BR5 ((SHARC_BASE & BR_BA_MSK) | BR_PS_32 | BR_MS_UPMA | BR_V ) |
| |
| /* |
| * Memory Periodic Timer Prescaler |
| */ |
| |
| /* periodic timer for refresh */ |
| #define CONFIG_SYS_MBMR_PTB 204 |
| |
| /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ |
| #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ |
| #define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ |
| |
| /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ |
| #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ |
| |
| #if defined (CONFIG_IVML24_16M) |
| # define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ |
| #elif defined (CONFIG_IVML24_32M) |
| # define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ |
| #elif defined (CONFIG_IVML24_64M) |
| # define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV8 /* setting for 1 bank */ |
| #endif |
| |
| |
| /* |
| * MBMR settings for SDRAM |
| */ |
| |
| #if defined (CONFIG_IVML24_16M) |
| /* 8 column SDRAM */ |
| # define CONFIG_SYS_MBMR_8COL ((CONFIG_SYS_MBMR_PTB << MBMR_PTB_SHIFT) | \ |
| MBMR_AMB_TYPE_0 | MBMR_DSB_1_CYCL | MBMR_G0CLB_A11 | \ |
| MBMR_RLFB_1X | MBMR_WLFB_1X | MBMR_TLFB_4X) |
| #elif defined (CONFIG_IVML24_32M) |
| /* 128 MBit SDRAM */ |
| # define CONFIG_SYS_MBMR_8COL ((CONFIG_SYS_MBMR_PTB << MBMR_PTB_SHIFT) | \ |
| MBMR_AMB_TYPE_1 | MBMR_DSB_1_CYCL | MBMR_G0CLB_A10 | \ |
| MBMR_RLFB_1X | MBMR_WLFB_1X | MBMR_TLFB_4X) |
| #elif defined (CONFIG_IVML24_64M) |
| /* 128 MBit SDRAM */ |
| # define CONFIG_SYS_MBMR_8COL ((CONFIG_SYS_MBMR_PTB << MBMR_PTB_SHIFT) | \ |
| MBMR_AMB_TYPE_1 | MBMR_DSB_1_CYCL | MBMR_G0CLB_A10 | \ |
| MBMR_RLFB_1X | MBMR_WLFB_1X | MBMR_TLFB_4X) |
| #endif |
| #endif /* __CONFIG_H */ |