| /* |
| * (C) Copyright 2000, 2001 |
| * Wolfgang Denk, DENX Software Engineering, wd@denx.de. |
| * |
| * (C) Copyright 2001 |
| * James F. Dougherty (jfd@cs.stanford.edu) |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * |
| * Configuration settings for the MOUSSE board. |
| * See also: http://www.vooha.com/ |
| * |
| */ |
| |
| /* ------------------------------------------------------------------------- */ |
| |
| /* |
| * board/config.h - configuration options, board specific |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* |
| * High Level Configuration Options |
| * (easy to change) |
| */ |
| |
| #define CONFIG_MPC824X 1 |
| #define CONFIG_MPC8240 1 |
| #define CONFIG_MOUSSE 1 |
| |
| #define CONFIG_SYS_TEXT_BASE 0xFFF00000 |
| #define CONFIG_SYS_LDSCRIPT "board/mousse/u-boot.lds" |
| |
| #define CONFIG_SYS_ADDR_MAP_B 1 |
| |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_BAUDRATE 9600 |
| #if 1 |
| #define CONFIG_BOOTCOMMAND "tftp 100000 vmlinux.img;bootm" /* autoboot command */ |
| #else |
| #define CONFIG_BOOTCOMMAND "bootm ffe10000" |
| #endif |
| #define CONFIG_BOOTARGS "console=ttyS0 root=/dev/nfs rw nfsroot=209.128.93.133:/boot nfsaddrs=209.128.93.133:209.128.93.138" |
| #define CONFIG_BOOTDELAY 3 |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_DATE |
| |
| |
| #define CONFIG_ENV_OVERWRITE 1 |
| #define CONFIG_ETH_ADDR "00:10:18:10:00:06" |
| |
| #define CONFIG_DOS_PARTITION 1 /* MSDOS bootable partitiion support */ |
| |
| #include "../board/mousse/mousse.h" |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #undef CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "=>" /* Monitor Command Prompt */ |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_MAXARGS 8 /* Max number of command args */ |
| |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_LOAD_ADDR 0x00100000 /* Default load address */ |
| |
| /*----------------------------------------------------------------------- |
| * Start addresses for the final memory configuration |
| * (Set up by the startup code) |
| * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
| |
| #ifdef DEBUG |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_SDRAM_BASE |
| #else |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE |
| #endif |
| |
| #ifdef DEBUG |
| #define CONFIG_SYS_MONITOR_LEN (4 << 20) /* lots of mem ... */ |
| #else |
| #define CONFIG_SYS_MONITOR_LEN (512 << 10) /* 512K PLCC bootrom */ |
| #endif |
| #define CONFIG_SYS_MALLOC_LEN (2*(4096 << 10)) /* 2*4096kB for malloc() */ |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ |
| #define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0 ... 32 MB in DRAM */ |
| |
| |
| #define CONFIG_SYS_EUMB_ADDR 0xFC000000 |
| |
| #define CONFIG_SYS_ISA_MEM 0xFD000000 |
| #define CONFIG_SYS_ISA_IO 0xFE000000 |
| |
| #define CONFIG_SYS_FLASH_BASE 0xFFF00000 |
| #define CONFIG_SYS_FLASH_SIZE ((uint)(512 * 1024)) |
| #define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 |
| #define FLASH_BASE0_PRELIM 0xFFF00000 /* 512K PLCC FLASH/AM29F040*/ |
| #define FLASH_BASE0_SIZE 0x80000 /* 512K */ |
| #define FLASH_BASE1_PRELIM 0xFFE10000 /* AMD 29LV160DB |
| 1MB - 64K FLASH0 SEG =960K |
| (size=0xf0000)*/ |
| |
| /* |
| * NS16550 Configuration |
| */ |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| |
| #define CONFIG_SYS_NS16550_CLK 18432000 |
| |
| #define CONFIG_SYS_NS16550_COM1 0xFFE08080 |
| |
| /*----------------------------------------------------------------------- |
| * Definitions for initial stack pointer and data area (in DPRAM) |
| */ |
| #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_MONITOR_LEN |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| /* |
| * Low Level Configuration Settings |
| * (address mappings, register initial values, etc.) |
| * You should know what you are doing if you make changes here. |
| * For the detail description refer to the MPC8240 user's manual. |
| */ |
| |
| #define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ |
| #define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 2 |
| #define CONFIG_SYS_HZ 1000 |
| |
| #define CONFIG_SYS_ETH_DEV_FN 0x00 |
| #define CONFIG_SYS_ETH_IOBASE 0x00104000 |
| |
| |
| /* Bit-field values for MCCR1. |
| */ |
| #define CONFIG_SYS_ROMNAL 8 |
| #define CONFIG_SYS_ROMFAL 8 |
| |
| /* Bit-field values for MCCR2. |
| */ |
| #define CONFIG_SYS_REFINT 0xf5 /* Refresh interval */ |
| |
| /* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. |
| */ |
| #define CONFIG_SYS_BSTOPRE 0x79 |
| |
| #ifdef INCLUDE_ECC |
| #define USE_ECC 1 |
| #else /* INCLUDE_ECC */ |
| #define USE_ECC 0 |
| #endif /* INCLUDE_ECC */ |
| |
| |
| /* Bit-field values for MCCR3. |
| */ |
| #define CONFIG_SYS_REFREC 8 /* Refresh to activate interval */ |
| #define CONFIG_SYS_RDLAT (4+USE_ECC) /* Data latancy from read command */ |
| |
| /* Bit-field values for MCCR4. |
| */ |
| #define CONFIG_SYS_PRETOACT 3 /* Precharge to activate interval */ |
| #define CONFIG_SYS_ACTTOPRE 5 /* Activate to Precharge interval */ |
| #define CONFIG_SYS_SDMODE_CAS_LAT 3 /* SDMODE CAS latancy */ |
| #define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE wrap type */ |
| #define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length */ |
| #define CONFIG_SYS_ACTORW 2 |
| #define CONFIG_SYS_REGISTERD_TYPE_BUFFER (1-USE_ECC) |
| |
| /* Memory bank settings. |
| * Only bits 20-29 are actually used from these vales to set the |
| * start/end addresses. The upper two bits will always be 0, and the lower |
| * 20 bits will be 0x00000 for a start address, or 0xfffff for an end |
| * address. Refer to the MPC8240 book. |
| */ |
| #define CONFIG_SYS_RAM_SIZE 0x04000000 /* 64MB */ |
| |
| |
| #define CONFIG_SYS_BANK0_START 0x00000000 |
| #define CONFIG_SYS_BANK0_END (CONFIG_SYS_RAM_SIZE - 1) |
| #define CONFIG_SYS_BANK0_ENABLE 1 |
| #define CONFIG_SYS_BANK1_START 0x3ff00000 |
| #define CONFIG_SYS_BANK1_END 0x3fffffff |
| #define CONFIG_SYS_BANK1_ENABLE 0 |
| #define CONFIG_SYS_BANK2_START 0x3ff00000 |
| #define CONFIG_SYS_BANK2_END 0x3fffffff |
| #define CONFIG_SYS_BANK2_ENABLE 0 |
| #define CONFIG_SYS_BANK3_START 0x3ff00000 |
| #define CONFIG_SYS_BANK3_END 0x3fffffff |
| #define CONFIG_SYS_BANK3_ENABLE 0 |
| #define CONFIG_SYS_BANK4_START 0x3ff00000 |
| #define CONFIG_SYS_BANK4_END 0x3fffffff |
| #define CONFIG_SYS_BANK4_ENABLE 0 |
| #define CONFIG_SYS_BANK5_START 0x3ff00000 |
| #define CONFIG_SYS_BANK5_END 0x3fffffff |
| #define CONFIG_SYS_BANK5_ENABLE 0 |
| #define CONFIG_SYS_BANK6_START 0x3ff00000 |
| #define CONFIG_SYS_BANK6_END 0x3fffffff |
| #define CONFIG_SYS_BANK6_ENABLE 0 |
| #define CONFIG_SYS_BANK7_START 0x3ff00000 |
| #define CONFIG_SYS_BANK7_END 0x3fffffff |
| #define CONFIG_SYS_BANK7_ENABLE 0 |
| |
| #define CONFIG_SYS_ODCR 0x7f |
| |
| |
| #define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 reatins the currently accessed page in memory |
| see 8240 book for details*/ |
| #define PCI_MEM_SPACE1_START 0x80000000 |
| #define PCI_MEM_SPACE2_START 0xfd000000 |
| |
| /* IBAT/DBAT Configuration */ |
| /* Ram: 64MB, starts at address-0, r/w instruction/data */ |
| #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U |
| #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L |
| |
| /* MPLD/Port-X I/O Space : data and instruction read/write, cache-inhibit */ |
| #define CONFIG_SYS_IBAT1U (PORTX_DEV_BASE | BATU_BL_128M | BATU_VS | BATU_VP) |
| #if 0 |
| #define CONFIG_SYS_IBAT1L (PORTX_DEV_BASE | BATL_PP_10 | BATL_MEMCOHERENCE |\ |
| BATL_WRITETHROUGH | BATL_CACHEINHIBIT) |
| #else |
| #define CONFIG_SYS_IBAT1L (PORTX_DEV_BASE | BATL_PP_10 |BATL_CACHEINHIBIT) |
| #endif |
| #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U |
| #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L |
| |
| /* PCI Memory region 1: 0x8XXX_XXXX PCI Mem space: EUMBAR, etc - 16MB */ |
| #define CONFIG_SYS_IBAT2U (PCI_MEM_SPACE1_START|BATU_BL_16M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT2L (PCI_MEM_SPACE1_START|BATL_PP_10 | BATL_GUARDEDSTORAGE|BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U |
| #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L |
| |
| /* PCI Memory region 2: PCI Devices in 0xFD space */ |
| #define CONFIG_SYS_IBAT3U (PCI_MEM_SPACE2_START|BATU_BL_16M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT3L (PCI_MEM_SPACE2_START|BATL_PP_10 | BATL_GUARDEDSTORAGE | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U |
| #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L |
| |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /*----------------------------------------------------------------------- |
| * FLASH organization |
| */ |
| #define CONFIG_SYS_MAX_FLASH_BANKS 3 /* Max number of flash banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 64 /* Max number of sectors in one bank */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #if 0 |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_OFFSET 0x8000 /* Offset of the Environment Sector */ |
| #define CONFIG_ENV_SIZE 0x4000 /* Size of the Environment Sector */ |
| #else |
| #define CONFIG_ENV_IS_IN_NVRAM 1 |
| #define CONFIG_ENV_ADDR NV_OFF_U_BOOT_ADDR /* PortX NVM Free addr*/ |
| #define CONFIG_ENV_OFFSET CONFIG_ENV_ADDR |
| #define CONFIG_ENV_SIZE NV_U_BOOT_ENV_SIZE /* 2K */ |
| #endif |
| /*----------------------------------------------------------------------- |
| * Cache Configuration |
| */ |
| #define CONFIG_SYS_CACHELINE_SIZE 16 |
| |
| /* Localizations */ |
| #if 0 |
| #define CONFIG_ETHADDR 0:0:0:0:1:d |
| #define CONFIG_IPADDR 172.16.40.113 |
| #define CONFIG_SERVERIP 172.16.40.111 |
| #else |
| #define CONFIG_ETHADDR 0:0:0:0:1:d |
| #define CONFIG_IPADDR 209.128.93.138 |
| #define CONFIG_SERVERIP 209.128.93.133 |
| #endif |
| |
| /*----------------------------------------------------------------------- |
| * PCI stuff |
| *----------------------------------------------------------------------- |
| */ |
| #define CONFIG_PCI /* include pci support */ |
| #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ |
| #undef CONFIG_PCI_PNP |
| |
| |
| #define CONFIG_TULIP |
| |
| #endif /* __CONFIG_H */ |