| /* |
| * Copyright 2006, 2010-2011 Freescale Semiconductor. |
| * |
| * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * MPC8641HPCN board configuration file |
| * |
| * Make sure you change the MAC address and other network params first, |
| * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file. |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_MPC86xx 1 /* MPC86xx */ |
| #define CONFIG_MPC8641 1 /* MPC8641 specific */ |
| #define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */ |
| #define CONFIG_MP 1 /* support multiple processors */ |
| #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ |
| /*#define CONFIG_PHYS_64BIT 1*/ /* Place devices in 36-bit space */ |
| #define CONFIG_ADDR_MAP 1 /* Use addr map */ |
| |
| /* |
| * default CCSRBAR is at 0xff700000 |
| * assume U-Boot is less than 0.5MB |
| */ |
| #define CONFIG_SYS_TEXT_BASE 0xeff00000 |
| |
| #ifdef RUN_DIAG |
| #define CONFIG_SYS_DIAG_ADDR CONFIG_SYS_FLASH_BASE |
| #endif |
| |
| /* |
| * virtual address to be used for temporary mappings. There |
| * should be 128k free at this VA. |
| */ |
| #define CONFIG_SYS_SCRATCH_VA 0xe0000000 |
| |
| #define CONFIG_SYS_SRIO |
| #define CONFIG_SRIO1 /* SRIO port 1 */ |
| |
| #define CONFIG_PCI 1 /* Enable PCI/PCIE */ |
| #define CONFIG_PCIE1 1 /* PCIE controler 1 (ULI bridge) */ |
| #define CONFIG_PCIE2 1 /* PCIE controler 2 (slot) */ |
| #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ |
| #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ |
| #define CONFIG_FSL_LAW 1 /* Use common FSL law init code */ |
| |
| #define CONFIG_TSEC_ENET /* tsec ethernet support */ |
| #define CONFIG_ENV_OVERWRITE |
| |
| #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ |
| #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ |
| #define CONFIG_SYS_NUM_ADDR_MAP 8 /* Number of addr map slots = 8 dbats */ |
| |
| #define CONFIG_ALTIVEC 1 |
| |
| /* |
| * L2CR setup -- make sure this is right for your board! |
| */ |
| #define CONFIG_SYS_L2 |
| #define L2_INIT 0 |
| #define L2_ENABLE (L2CR_L2E) |
| |
| #ifndef CONFIG_SYS_CLK_FREQ |
| #ifndef __ASSEMBLY__ |
| extern unsigned long get_board_sys_clk(unsigned long dummy); |
| #endif |
| #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) |
| #endif |
| |
| #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ |
| #define CONFIG_SYS_MEMTEST_END 0x00400000 |
| |
| /* |
| * With the exception of PCI Memory and Rapid IO, most devices will simply |
| * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA |
| * when 36-bit is enabled. When 36-bit is not enabled, these bits are 0. |
| */ |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f |
| #else |
| #define CONFIG_SYS_PHYS_ADDR_HIGH 0x00000000 |
| #endif |
| |
| /* |
| * Base addresses -- Note these are effective addresses where the |
| * actual resources get mapped (not physical addresses) |
| */ |
| #define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ |
| #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ |
| #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ |
| |
| /* Physical addresses */ |
| #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR |
| #define CONFIG_SYS_CCSRBAR_PHYS_HIGH CONFIG_SYS_PHYS_ADDR_HIGH |
| #define CONFIG_SYS_CCSRBAR_PHYS \ |
| PAIRED_PHYS_TO_PHYS(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ |
| CONFIG_SYS_CCSRBAR_PHYS_HIGH) |
| |
| #define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */ |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_FSL_DDR2 |
| #undef CONFIG_FSL_DDR_INTERACTIVE |
| #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ |
| #define CONFIG_DDR_SPD |
| |
| #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ |
| #define CONFIG_MEM_INIT_VALUE 0xDeadBeef |
| |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ |
| #define CONFIG_VERY_BIG_RAM |
| |
| #define CONFIG_NUM_DDR_CONTROLLERS 2 |
| #define CONFIG_DIMM_SLOTS_PER_CTLR 2 |
| #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) |
| |
| /* |
| * I2C addresses of SPD EEPROMs |
| */ |
| #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ |
| #define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 0 DIMM 1 */ |
| #define SPD_EEPROM_ADDRESS3 0x53 /* CTLR 1 DIMM 0 */ |
| #define SPD_EEPROM_ADDRESS4 0x54 /* CTLR 1 DIMM 1 */ |
| |
| |
| /* |
| * These are used when DDR doesn't use SPD. |
| */ |
| #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ |
| #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F |
| #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ |
| #define CONFIG_SYS_DDR_TIMING_3 0x00000000 |
| #define CONFIG_SYS_DDR_TIMING_0 0x00260802 |
| #define CONFIG_SYS_DDR_TIMING_1 0x39357322 |
| #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 |
| #define CONFIG_SYS_DDR_MODE_1 0x00480432 |
| #define CONFIG_SYS_DDR_MODE_2 0x00000000 |
| #define CONFIG_SYS_DDR_INTERVAL 0x06090100 |
| #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef |
| #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 |
| #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 |
| #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 |
| #define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ |
| #define CONFIG_SYS_DDR_CONTROL2 0x04400000 |
| |
| #define CONFIG_ID_EEPROM |
| #define CONFIG_SYS_I2C_EEPROM_NXID |
| #define CONFIG_ID_EEPROM |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 |
| |
| #define CONFIG_SYS_FLASH_BASE 0xef800000 /* start of FLASH 8M */ |
| #define CONFIG_SYS_FLASH_BASE_PHYS_LOW CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_FLASH_BASE_PHYS \ |
| PAIRED_PHYS_TO_PHYS(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ |
| CONFIG_SYS_PHYS_ADDR_HIGH) |
| |
| #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} |
| |
| #define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ |
| | 0x00001001) /* port size 16bit */ |
| #define CONFIG_SYS_OR0_PRELIM 0xff806ff7 /* 8MB Boot Flash area*/ |
| |
| #define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CF_BASE_PHYS) \ |
| | 0x00001001) /* port size 16bit */ |
| #define CONFIG_SYS_OR2_PRELIM 0xffffeff7 /* 32k Compact Flash */ |
| |
| #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) \ |
| | 0x00000801) /* port size 8bit */ |
| #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32k PIXIS area*/ |
| |
| /* |
| * The LBC_BASE is the base of the region that contains the PIXIS and the CF. |
| * The PIXIS and CF by themselves aren't large enough to take up the 128k |
| * required for the smallest BAT mapping, so there's a 64k hole. |
| */ |
| #define CONFIG_SYS_LBC_BASE 0xffde0000 |
| #define CONFIG_SYS_LBC_BASE_PHYS_LOW CONFIG_SYS_LBC_BASE |
| |
| #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ |
| #define PIXIS_BASE (CONFIG_SYS_LBC_BASE + 0x00010000) |
| #define PIXIS_BASE_PHYS_LOW (CONFIG_SYS_LBC_BASE_PHYS_LOW + 0x00010000) |
| #define PIXIS_BASE_PHYS PAIRED_PHYS_TO_PHYS(PIXIS_BASE_PHYS_LOW, \ |
| CONFIG_SYS_PHYS_ADDR_HIGH) |
| #define PIXIS_SIZE 0x00008000 /* 32k */ |
| #define PIXIS_ID 0x0 /* Board ID at offset 0 */ |
| #define PIXIS_VER 0x1 /* Board version at offset 1 */ |
| #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ |
| #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ |
| #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */ |
| #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ |
| #define PIXIS_VCTL 0x10 /* VELA Control Register */ |
| #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ |
| #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ |
| #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ |
| #define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ |
| #define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ |
| #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ |
| #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ |
| #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ |
| #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ |
| #define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ |
| |
| /* Compact flash shares a BAT with PIXIS; make sure they're contiguous */ |
| #define CF_BASE (PIXIS_BASE + PIXIS_SIZE) |
| #define CF_BASE_PHYS (PIXIS_BASE_PHYS + PIXIS_SIZE) |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ |
| |
| #undef CONFIG_SYS_FLASH_CHECKSUM |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ |
| |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_EMPTY_INFO |
| |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| #define CONFIG_SYS_RAMBOOT |
| #else |
| #undef CONFIG_SYS_RAMBOOT |
| #endif |
| |
| #if defined(CONFIG_SYS_RAMBOOT) |
| #undef CONFIG_SPD_EEPROM |
| #define CONFIG_SYS_SDRAM_SIZE 256 |
| #endif |
| |
| #undef CONFIG_CLOCKS_IN_MHZ |
| |
| #define CONFIG_SYS_INIT_RAM_LOCK 1 |
| #ifndef CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ |
| #else |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ |
| #endif |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ |
| |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ |
| #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ |
| |
| /* Serial Port */ |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) |
| |
| /* Use the HUSH parser */ |
| #define CONFIG_SYS_HUSH_PARSER |
| |
| /* |
| * Pass open firmware flat tree to kernel |
| */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| #define CONFIG_OF_STDOUT_VIA_ALIAS 1 |
| |
| /* |
| * I2C |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 400000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 |
| #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } |
| |
| /* |
| * RapidIO MMU |
| */ |
| #define CONFIG_SYS_SRIO1_MEM_BASE 0x80000000 /* base address */ |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW 0x00000000 |
| #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x0000000c |
| #else |
| #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW CONFIG_SYS_SRIO1_MEM_BASE |
| #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x00000000 |
| #endif |
| #define CONFIG_SYS_SRIO1_MEM_PHYS \ |
| PAIRED_PHYS_TO_PHYS(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ |
| CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) |
| #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 128M */ |
| |
| /* |
| * General PCI |
| * Addresses are mapped 1-1. |
| */ |
| |
| #define CONFIG_SYS_PCIE1_NAME "ULI" |
| #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 |
| #ifdef CONFIG_PHYS_64BIT |
| #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW 0x00000000 |
| #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x0000000c |
| #else |
| #define CONFIG_SYS_PCIE1_MEM_BUS CONFIG_SYS_PCIE1_MEM_VIRT |
| #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW CONFIG_SYS_PCIE1_MEM_VIRT |
| #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x00000000 |
| #endif |
| #define CONFIG_SYS_PCIE1_MEM_PHYS \ |
| PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ |
| CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) |
| #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 |
| #define CONFIG_SYS_PCIE1_IO_PHYS_LOW CONFIG_SYS_PCIE1_IO_VIRT |
| #define CONFIG_SYS_PCIE1_IO_PHYS \ |
| PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ |
| CONFIG_SYS_PHYS_ADDR_HIGH) |
| #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */ |
| |
| #ifdef CONFIG_PHYS_64BIT |
| /* |
| * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT. |
| * This will increase the amount of PCI address space available for |
| * for mapping RAM. |
| */ |
| #define CONFIG_SYS_PCIE2_MEM_BUS CONFIG_SYS_PCIE1_MEM_BUS |
| #else |
| #define CONFIG_SYS_PCIE2_MEM_BUS (CONFIG_SYS_PCIE1_MEM_BUS \ |
| + CONFIG_SYS_PCIE1_MEM_SIZE) |
| #endif |
| #define CONFIG_SYS_PCIE2_MEM_VIRT (CONFIG_SYS_PCIE1_MEM_VIRT \ |
| + CONFIG_SYS_PCIE1_MEM_SIZE) |
| #define CONFIG_SYS_PCIE2_MEM_PHYS_LOW (CONFIG_SYS_PCIE1_MEM_PHYS_LOW \ |
| + CONFIG_SYS_PCIE1_MEM_SIZE) |
| #define CONFIG_SYS_PCIE2_MEM_PHYS_HIGH CONFIG_SYS_PCIE1_MEM_PHYS_HIGH |
| #define CONFIG_SYS_PCIE2_MEM_PHYS (CONFIG_SYS_PCIE1_MEM_PHYS \ |
| + CONFIG_SYS_PCIE1_MEM_SIZE) |
| #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ |
| #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 |
| #define CONFIG_SYS_PCIE2_IO_VIRT (CONFIG_SYS_PCIE1_IO_VIRT \ |
| + CONFIG_SYS_PCIE1_IO_SIZE) |
| #define CONFIG_SYS_PCIE2_IO_PHYS_LOW (CONFIG_SYS_PCIE1_IO_PHYS_LOW \ |
| + CONFIG_SYS_PCIE1_IO_SIZE) |
| #define CONFIG_SYS_PCIE2_IO_PHYS (CONFIG_SYS_PCIE1_IO_PHYS \ |
| + CONFIG_SYS_PCIE1_IO_SIZE) |
| #define CONFIG_SYS_PCIE2_IO_SIZE CONFIG_SYS_PCIE1_IO_SIZE |
| |
| #if defined(CONFIG_PCI) |
| |
| #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| |
| #undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE |
| |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #define CONFIG_RTL8139 |
| |
| #undef CONFIG_EEPRO100 |
| #undef CONFIG_TULIP |
| |
| /************************************************************ |
| * USB support |
| ************************************************************/ |
| #define CONFIG_PCI_OHCI 1 |
| #define CONFIG_USB_OHCI_NEW 1 |
| #define CONFIG_USB_KEYBOARD 1 |
| #define CONFIG_SYS_STDIO_DEREGISTER |
| #define CONFIG_SYS_USB_EVENT_POLL 1 |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 |
| #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 |
| |
| /*PCIE video card used*/ |
| #define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT |
| |
| /*PCI video card used*/ |
| /*#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT*/ |
| |
| /* video */ |
| #define CONFIG_VIDEO |
| |
| #if defined(CONFIG_VIDEO) |
| #define CONFIG_BIOSEMU |
| #define CONFIG_CFB_CONSOLE |
| #define CONFIG_VIDEO_SW_CURSOR |
| #define CONFIG_VGA_AS_SINGLE_DEVICE |
| #define CONFIG_ATI_RADEON_FB |
| #define CONFIG_VIDEO_LOGO |
| /*#define CONFIG_CONSOLE_CURSOR*/ |
| #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT |
| #endif |
| |
| #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_SCSI_AHCI |
| |
| #ifdef CONFIG_SCSI_AHCI |
| #define CONFIG_SATA_ULI5288 |
| #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 |
| #define CONFIG_SYS_SCSI_MAX_LUN 1 |
| #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) |
| #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE |
| #endif |
| |
| #endif /* CONFIG_PCI */ |
| |
| #if defined(CONFIG_TSEC_ENET) |
| |
| #define CONFIG_MII 1 /* MII PHY management */ |
| |
| #define CONFIG_TSEC1 1 |
| #define CONFIG_TSEC1_NAME "eTSEC1" |
| #define CONFIG_TSEC2 1 |
| #define CONFIG_TSEC2_NAME "eTSEC2" |
| #define CONFIG_TSEC3 1 |
| #define CONFIG_TSEC3_NAME "eTSEC3" |
| #define CONFIG_TSEC4 1 |
| #define CONFIG_TSEC4_NAME "eTSEC4" |
| |
| #define TSEC1_PHY_ADDR 0 |
| #define TSEC2_PHY_ADDR 1 |
| #define TSEC3_PHY_ADDR 2 |
| #define TSEC4_PHY_ADDR 3 |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| #define TSEC3_PHYIDX 0 |
| #define TSEC4_PHYIDX 0 |
| #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| |
| #define CONFIG_ETHPRIME "eTSEC1" |
| |
| #endif /* CONFIG_TSEC_ENET */ |
| |
| |
| #ifdef CONFIG_PHYS_64BIT |
| #define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8) |
| #define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2) |
| |
| /* Put physical address into the BAT format */ |
| #define BAT_PHYS_ADDR(low, high) \ |
| (low | PHYS_HIGH_TO_BXPN(high) | PHYS_HIGH_TO_BX(high)) |
| /* Convert high/low pairs to actual 64-bit value */ |
| #define PAIRED_PHYS_TO_PHYS(low, high) (low | ((u64)high << 32)) |
| #else |
| /* 32-bit systems just ignore the "high" bits */ |
| #define BAT_PHYS_ADDR(low, high) (low) |
| #define PAIRED_PHYS_TO_PHYS(low, high) (low) |
| #endif |
| |
| /* |
| * BAT0 DDR |
| */ |
| #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) |
| |
| /* |
| * BAT1 LBC (PIXIS/CF) |
| */ |
| #define CONFIG_SYS_DBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ |
| CONFIG_SYS_PHYS_ADDR_HIGH) \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT | \ |
| BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT1U (CONFIG_SYS_LBC_BASE | BATU_BL_128K \ |
| | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ |
| CONFIG_SYS_PHYS_ADDR_HIGH) \ |
| | BATL_PP_RW | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U |
| |
| /* if CONFIG_PCI: |
| * BAT2 PCIE1 and PCIE1 MEM |
| * if CONFIG_RIO |
| * BAT2 Rapidio Memory |
| */ |
| #ifdef CONFIG_PCI |
| #define CONFIG_PCI_INDIRECT_BRIDGE |
| #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ |
| CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT \ |
| | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \ |
| | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ |
| CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U |
| #else /* CONFIG_RIO */ |
| #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ |
| CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT | \ |
| BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT2U (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M \ |
| | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ |
| CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U |
| #endif |
| |
| /* |
| * BAT3 CCSR Space |
| */ |
| #define CONFIG_SYS_DBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ |
| CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT \ |
| | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \ |
| | BATU_VP) |
| #define CONFIG_SYS_IBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ |
| CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U |
| |
| #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) |
| #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT \ |
| | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ |
| | BATU_BL_1M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU |
| #endif |
| |
| /* |
| * BAT4 PCIE1_IO and PCIE2_IO |
| */ |
| #define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ |
| CONFIG_SYS_PHYS_ADDR_HIGH) \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT \ |
| | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \ |
| | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ |
| CONFIG_SYS_PHYS_ADDR_HIGH) \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT) |
| #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U |
| |
| /* |
| * BAT5 Init RAM for stack in the CPU DCache (no backing memory) |
| */ |
| #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L |
| #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U |
| |
| /* |
| * BAT6 FLASH |
| */ |
| #define CONFIG_SYS_DBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ |
| CONFIG_SYS_PHYS_ADDR_HIGH) \ |
| | BATL_PP_RW | BATL_CACHEINHIBIT \ |
| | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \ |
| | BATU_VP) |
| #define CONFIG_SYS_IBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ |
| CONFIG_SYS_PHYS_ADDR_HIGH) \ |
| | BATL_PP_RW | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U |
| |
| /* Map the last 1M of flash where we're running from reset */ |
| #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ |
| | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) |
| #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ |
| | BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY |
| |
| /* |
| * BAT7 FREE - used later for tmp mappings |
| */ |
| #define CONFIG_SYS_DBAT7L 0x00000000 |
| #define CONFIG_SYS_DBAT7U 0x00000000 |
| #define CONFIG_SYS_IBAT7L 0x00000000 |
| #define CONFIG_SYS_IBAT7U 0x00000000 |
| |
| /* |
| * Environment |
| */ |
| #ifndef CONFIG_SYS_RAMBOOT |
| #define CONFIG_ENV_IS_IN_FLASH 1 |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x60000) |
| #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ |
| #else |
| #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| #endif |
| #define CONFIG_ENV_SIZE 0x2000 |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_REGINFO |
| |
| #if defined(CONFIG_SYS_RAMBOOT) |
| #undef CONFIG_CMD_SAVEENV |
| #endif |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #define CONFIG_CMD_SCSI |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_CMD_USB |
| #endif |
| |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_CMDLINE_EDITING /* Command-line editing */ |
| #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ |
| #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| |
| /* The mac addresses for all ethernet interface */ |
| #if defined(CONFIG_TSEC_ENET) |
| #define CONFIG_ETHADDR 00:E0:0C:00:00:01 |
| #define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD |
| #define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD |
| #define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD |
| #endif |
| |
| #define CONFIG_HAS_ETH0 1 |
| #define CONFIG_HAS_ETH1 1 |
| #define CONFIG_HAS_ETH2 1 |
| #define CONFIG_HAS_ETH3 1 |
| |
| #define CONFIG_IPADDR 192.168.1.100 |
| |
| #define CONFIG_HOSTNAME unknown |
| #define CONFIG_ROOTPATH "/opt/nfsroot" |
| #define CONFIG_BOOTFILE "uImage" |
| #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ |
| |
| #define CONFIG_SERVERIP 192.168.1.1 |
| #define CONFIG_GATEWAYIP 192.168.1.1 |
| #define CONFIG_NETMASK 255.255.255.0 |
| |
| /* default location for tftp and bootm */ |
| #define CONFIG_LOADADDR 1000000 |
| |
| #define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ |
| #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ |
| "tftpflash=tftpboot $loadaddr $uboot; " \ |
| "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ |
| " +$filesize; " \ |
| "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ |
| " +$filesize; " \ |
| "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ |
| " $filesize; " \ |
| "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ |
| " +$filesize; " \ |
| "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ |
| " $filesize\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=2000000\0" \ |
| "ramdiskfile=your.ramdisk.u-boot\0" \ |
| "fdtaddr=c00000\0" \ |
| "fdtfile=mpc8641_hpcn.dtb\0" \ |
| "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0" \ |
| "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \ |
| "maxcpus=2" |
| |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND |
| |
| #endif /* __CONFIG_H */ |