include/configs/PN62.h - platform/external/u-boot - Gitiles

 /*
  * (C) Copyright 2002
  * Wolfgang Grandegger, DENX Software Engineering, wg@denx.de.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /* ------------------------------------------------------------------------- */

 /*
  * board/config.h - configuration options, board specific
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_MPC824X		1
 #define CONFIG_MPC8240		1
 #define CONFIG_PN62		1

 #define	CONFIG_SYS_TEXT_BASE	0xFFF00000

 #define CONFIG_CONS_INDEX	1


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_BSP

 #undef CONFIG_CMD_FLASH
 #undef CONFIG_CMD_IMLS
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_SAVEENV
 #undef CONFIG_CMD_SOURCE


 #define CONFIG_BAUDRATE		19200	/* console baudrate		*/

 #define CONFIG_BOOTDELAY	1	/* autoboot after n seconds	*/

 #define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */

 #define CONFIG_SERVERIP		10.0.0.201
 #define CONFIG_IPADDR		10.0.0.200
 #define CONFIG_ROOTPATH		"/opt/eldk/ppc_82xx"
 #define CONFIG_NETMASK		255.255.255.0
 #undef CONFIG_BOOTARGS
 #if 0
 /* Boot Linux with NFS root filesystem */
 #define CONFIG_BOOTCOMMAND \
 			"setenv verify y;" \
 			"setenv bootargs console=ttyS0,19200 mem=31M quiet " \
 			"root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
 			"ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \
 			"loadp 100000; bootm"
 			/* "tftpboot 100000 uImage; bootm" */
 #else
 /* Boot Linux with RAMdisk based filesystem (initrd, BusyBox) */
 #define CONFIG_BOOTCOMMAND \
 			"setenv verify n;" \
 			"setenv bootargs console=ttyS0,19200 mem=31M quiet " \
 			"root=/dev/ram rw " \
 			"ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \
 			"loadp 200000; bootm"
 #endif

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP		1		/* undef to save memory		*/
 #define CONFIG_SYS_PROMPT		"=> "		/* Monitor Command Prompt	*/
 #define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size	*/
 #define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 #define CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address		*/
 #define CONFIG_SYS_HZ			1000		/* decrementer freq: 1 ms ticks */

 #define CONFIG_PRAM		1024		/* reserve 1 MB protected RAM	*/

 #define CONFIG_MISC_INIT_R	1		/* call misc_init_r() on init	*/

 #define CONFIG_HAS_ETH1		1		/* add support for eth1addr	*/

 #define CONFIG_SHOW_BOOT_PROGRESS 1		/* Show boot progress on LEDs   */

 /*
  * PCI stuff
  */
 #define CONFIG_PCI				/* include pci support		*/
 #define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
 #define CONFIG_PCI_PNP				/* we need Plug 'n Play		*/
 #if 0
 #define CONFIG_PCI_SCAN_SHOW			/* show PCI auto-scan at boot	*/
 #endif

 /*
  * Networking stuff
  */

 #define CONFIG_PCNET				/* there are 2 AMD PCnet 79C973	*/
 #define CONFIG_PCNET_79C973

 #define _IO_BASE		0xfe000000	/* points to PCI I/O space	*/


 /*
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_MAX_RAM_SIZE	0x10000000

 #define CONFIG_SYS_RESET_ADDRESS	0xfff00100

 #undef	CONFIG_SYS_RAMBOOT
 #define CONFIG_SYS_MONITOR_LEN		0x00030000
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE


 #define CONFIG_SYS_INIT_RAM_ADDR	0x40000000
 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)


 #define CONFIG_SYS_NO_FLASH		1		/* There is no FLASH memory	*/

 #define CONFIG_ENV_IS_NOWHERE	1		/* Store ENV in memory only	*/
 #define CONFIG_ENV_OFFSET		0x00004000	/* Offset of Environment Sector */
 #define CONFIG_ENV_SIZE		0x00002000	/* Total Size of Environment Sector */

 #define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()	*/

 #define CONFIG_SYS_MEMTEST_START	0x00004000	/* memtest works on		*/
 #define CONFIG_SYS_MEMTEST_END		0x01f00000	/* 0 ... 32 MB in DRAM		*/

 /*
  * Serial port configuration
  */

 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL

 #define CONFIG_SYS_NS16550_REG_SIZE	1

 #define CONFIG_SYS_NS16550_CLK		1843200

 #define CONFIG_SYS_NS16550_COM1	0xff800008
 #define CONFIG_SYS_NS16550_COM2	0xff800000

 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  */

 #define CONFIG_SYS_CLK_FREQ  33333333	/* external frequency to pll */
 #define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER  3

 #define CONFIG_SYS_EUMB_ADDR		0xFCE00000

 /* MCCR1 */
 #define CONFIG_SYS_ROMNAL		3	/* rom/flash next access time		*/
 #define CONFIG_SYS_ROMFAL		7	/* rom/flash access time		*/

 /* MCCR2 */
 #define CONFIG_SYS_ASRISE		6	/* ASRISE in clocks			*/
 #define CONFIG_SYS_ASFALL		12	/* ASFALL in clocks			*/
 #define CONFIG_SYS_REFINT		5600	/* REFINT in clocks			*/

 /* MCCR3 */
 #define CONFIG_SYS_BSTOPRE		0x3cf	/* Burst To Precharge			*/
 #define CONFIG_SYS_REFREC		2	/* Refresh to activate interval		*/
 #define CONFIG_SYS_RDLAT		3	/* data latency from read command	*/

 /* MCCR4 */
 #define CONFIG_SYS_PRETOACT		1	/* Precharge to activate interval	*/
 #define CONFIG_SYS_ACTTOPRE		3	/* Activate to Precharge interval	*/
 #define CONFIG_SYS_ACTORW		2	/* Activate to R/W			*/
 #define CONFIG_SYS_SDMODE_CAS_LAT	2	/* SDMODE CAS latency			*/
 #define CONFIG_SYS_SDMODE_WRAP		0	/* SDMODE Wrap type			*/
 #define CONFIG_SYS_SDMODE_BURSTLEN	2	/* SDMODE Burst length 2=4, 3=8		*/
 #define CONFIG_SYS_REGISTERD_TYPE_BUFFER   1

 /* Memory bank settings:
  *
  * only bits 20-29 are actually used from these vales to set the
  * start/qend address the upper two bits will be 0, and the lower 20
  * bits will be set to 0x00000 for a start address, or 0xfffff for an
  * end address
  */
 #define CONFIG_SYS_BANK0_START		0x00000000
 #define CONFIG_SYS_BANK0_END		(CONFIG_SYS_MAX_RAM_SIZE - 1)
 #define CONFIG_SYS_BANK0_ENABLE	1
 #define CONFIG_SYS_BANK1_START		0x00000000
 #define CONFIG_SYS_BANK1_END		0x00000000
 #define CONFIG_SYS_BANK1_ENABLE	0
 #define CONFIG_SYS_BANK2_START		0x00000000
 #define CONFIG_SYS_BANK2_END		0x00000000
 #define CONFIG_SYS_BANK2_ENABLE	0
 #define CONFIG_SYS_BANK3_START		0x00000000
 #define CONFIG_SYS_BANK3_END		0x00000000
 #define CONFIG_SYS_BANK3_ENABLE	0
 #define CONFIG_SYS_BANK4_START		0x00000000
 #define CONFIG_SYS_BANK4_END		0x00000000
 #define CONFIG_SYS_BANK4_ENABLE	0
 #define CONFIG_SYS_BANK5_START		0x00000000
 #define CONFIG_SYS_BANK5_END		0x00000000
 #define CONFIG_SYS_BANK5_ENABLE	0
 #define CONFIG_SYS_BANK6_START		0x00000000
 #define CONFIG_SYS_BANK6_END		0x00000000
 #define CONFIG_SYS_BANK6_ENABLE	0
 #define CONFIG_SYS_BANK7_START		0x00000000
 #define CONFIG_SYS_BANK7_END		0x00000000
 #define CONFIG_SYS_BANK7_ENABLE	0

 /*
  * Memory bank enable bitmask, specifying which of the banks defined above
  * are actually present. MSB is for bank #7, LSB is for bank #0.
  */
 #define CONFIG_SYS_BANK_ENABLE		0x01

 #define CONFIG_SYS_ODCR		0xff	/* configures line driver impedances,	*/
 					/* see 8240 book for bit definitions	*/
 #define CONFIG_SYS_PGMAX		0x32	/* how long the 8240 retains the	*/
 					/* currently accessed page in memory	*/
 					/* see 8240 book for details		*/

 /* SDRAM 0 - 256MB */
 #define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)

 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT1U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)

 /* PCI memory space */
 #define CONFIG_SYS_IBAT2L	(0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT2U	(0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)

 /* Config addrs, etc */
 #define CONFIG_SYS_IBAT3L	(0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
 #define CONFIG_SYS_IBAT3U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)

 #define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
 #define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
 #define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
 #define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
 #define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
 #define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
 #define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
 #define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

 /*
  * Cache Configuration
  */
 #define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8240 CPU			*/
 #if defined(CONFIG_CMD_KGDB)
 #  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif

 #endif	/* __CONFIG_H */
	/*
	* (C) Copyright 2002
	* Wolfgang Grandegger, DENX Software Engineering, wg@denx.de.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/* ------------------------------------------------------------------------- */

	/*
	* board/config.h - configuration options, board specific
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_MPC824X 1
	#define CONFIG_MPC8240 1
	#define CONFIG_PN62 1

	#define CONFIG_SYS_TEXT_BASE 0xFFF00000

	#define CONFIG_CONS_INDEX 1


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_PCI
	#define CONFIG_CMD_BSP

	#undef CONFIG_CMD_FLASH
	#undef CONFIG_CMD_IMLS
	#undef CONFIG_CMD_LOADS
	#undef CONFIG_CMD_SAVEENV
	#undef CONFIG_CMD_SOURCE


	#define CONFIG_BAUDRATE 19200 /* console baudrate */

	#define CONFIG_BOOTDELAY 1 /* autoboot after n seconds */

	#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */

	#define CONFIG_SERVERIP 10.0.0.201
	#define CONFIG_IPADDR 10.0.0.200
	#define CONFIG_ROOTPATH "/opt/eldk/ppc_82xx"
	#define CONFIG_NETMASK 255.255.255.0
	#undef CONFIG_BOOTARGS
	#if 0
	/* Boot Linux with NFS root filesystem */
	#define CONFIG_BOOTCOMMAND \
	"setenv verify y;" \
	"setenv bootargs console=ttyS0,19200 mem=31M quiet " \
	"root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
	"ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \
	"loadp 100000; bootm"
	/* "tftpboot 100000 uImage; bootm" */
	#else
	/* Boot Linux with RAMdisk based filesystem (initrd, BusyBox) */
	#define CONFIG_BOOTCOMMAND \
	"setenv verify n;" \
	"setenv bootargs console=ttyS0,19200 mem=31M quiet " \
	"root=/dev/ram rw " \
	"ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \
	"loadp 200000; bootm"
	#endif

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP 1 /* undef to save memory */
	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
	#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */

	#define CONFIG_PRAM 1024 /* reserve 1 MB protected RAM */

	#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() on init */

	#define CONFIG_HAS_ETH1 1 /* add support for eth1addr */

	#define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */

	/*
	* PCI stuff
	*/
	#define CONFIG_PCI /* include pci support */
	#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
	#define CONFIG_PCI_PNP /* we need Plug 'n Play */
	#if 0
	#define CONFIG_PCI_SCAN_SHOW /* show PCI auto-scan at boot */
	#endif

	/*
	* Networking stuff
	*/

	#define CONFIG_PCNET /* there are 2 AMD PCnet 79C973 */
	#define CONFIG_PCNET_79C973

	#define _IO_BASE 0xfe000000 /* points to PCI I/O space */


	/*
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
	*/
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_MAX_RAM_SIZE 0x10000000

	#define CONFIG_SYS_RESET_ADDRESS 0xfff00100

	#undef CONFIG_SYS_RAMBOOT
	#define CONFIG_SYS_MONITOR_LEN 0x00030000
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE


	#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)


	#define CONFIG_SYS_NO_FLASH 1 /* There is no FLASH memory */

	#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
	#define CONFIG_ENV_OFFSET 0x00004000 /* Offset of Environment Sector */
	#define CONFIG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */

	#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */

	#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x01f00000 /* 0 ... 32 MB in DRAM */

	/*
	* Serial port configuration
	*/

	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL

	#define CONFIG_SYS_NS16550_REG_SIZE 1

	#define CONFIG_SYS_NS16550_CLK 1843200

	#define CONFIG_SYS_NS16550_COM1 0xff800008
	#define CONFIG_SYS_NS16550_COM2 0xff800000

	/*
	* Low Level Configuration Settings
	* (address mappings, register initial values, etc.)
	* You should know what you are doing if you make changes here.
	*/

	#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
	#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 3

	#define CONFIG_SYS_EUMB_ADDR 0xFCE00000

	/* MCCR1 */
	#define CONFIG_SYS_ROMNAL 3 /* rom/flash next access time */
	#define CONFIG_SYS_ROMFAL 7 /* rom/flash access time */

	/* MCCR2 */
	#define CONFIG_SYS_ASRISE 6 /* ASRISE in clocks */
	#define CONFIG_SYS_ASFALL 12 /* ASFALL in clocks */
	#define CONFIG_SYS_REFINT 5600 /* REFINT in clocks */

	/* MCCR3 */
	#define CONFIG_SYS_BSTOPRE 0x3cf /* Burst To Precharge */
	#define CONFIG_SYS_REFREC 2 /* Refresh to activate interval */
	#define CONFIG_SYS_RDLAT 3 /* data latency from read command */

	/* MCCR4 */
	#define CONFIG_SYS_PRETOACT 1 /* Precharge to activate interval */
	#define CONFIG_SYS_ACTTOPRE 3 /* Activate to Precharge interval */
	#define CONFIG_SYS_ACTORW 2 /* Activate to R/W */
	#define CONFIG_SYS_SDMODE_CAS_LAT 2 /* SDMODE CAS latency */
	#define CONFIG_SYS_SDMODE_WRAP 0 /* SDMODE Wrap type */
	#define CONFIG_SYS_SDMODE_BURSTLEN 2 /* SDMODE Burst length 2=4, 3=8 */
	#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1

	/* Memory bank settings:
	*
	* only bits 20-29 are actually used from these vales to set the
	* start/qend address the upper two bits will be 0, and the lower 20
	* bits will be set to 0x00000 for a start address, or 0xfffff for an
	* end address
	*/
	#define CONFIG_SYS_BANK0_START 0x00000000
	#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
	#define CONFIG_SYS_BANK0_ENABLE 1
	#define CONFIG_SYS_BANK1_START 0x00000000
	#define CONFIG_SYS_BANK1_END 0x00000000
	#define CONFIG_SYS_BANK1_ENABLE 0
	#define CONFIG_SYS_BANK2_START 0x00000000
	#define CONFIG_SYS_BANK2_END 0x00000000
	#define CONFIG_SYS_BANK2_ENABLE 0
	#define CONFIG_SYS_BANK3_START 0x00000000
	#define CONFIG_SYS_BANK3_END 0x00000000
	#define CONFIG_SYS_BANK3_ENABLE 0
	#define CONFIG_SYS_BANK4_START 0x00000000
	#define CONFIG_SYS_BANK4_END 0x00000000
	#define CONFIG_SYS_BANK4_ENABLE 0
	#define CONFIG_SYS_BANK5_START 0x00000000
	#define CONFIG_SYS_BANK5_END 0x00000000
	#define CONFIG_SYS_BANK5_ENABLE 0
	#define CONFIG_SYS_BANK6_START 0x00000000
	#define CONFIG_SYS_BANK6_END 0x00000000
	#define CONFIG_SYS_BANK6_ENABLE 0
	#define CONFIG_SYS_BANK7_START 0x00000000
	#define CONFIG_SYS_BANK7_END 0x00000000
	#define CONFIG_SYS_BANK7_ENABLE 0

	/*
	* Memory bank enable bitmask, specifying which of the banks defined above
	* are actually present. MSB is for bank #7, LSB is for bank #0.
	*/
	#define CONFIG_SYS_BANK_ENABLE 0x01

	#define CONFIG_SYS_ODCR 0xff /* configures line driver impedances, */
	/* see 8240 book for bit definitions */
	#define CONFIG_SYS_PGMAX 0x32 /* how long the 8240 retains the */
	/* currently accessed page in memory */
	/* see 8240 book for details */

	/* SDRAM 0 - 256MB */
	#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \| BATL_PP_10 \| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)

	#define CONFIG_SYS_IBAT1L (CONFIG_SYS_INIT_RAM_ADDR \| BATL_PP_10 \| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT1U (CONFIG_SYS_INIT_RAM_ADDR \| BATU_BL_128K \| BATU_VS \| BATU_VP)

	/* PCI memory space */
	#define CONFIG_SYS_IBAT2L (0x80000000 \| BATL_PP_10 \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT2U (0x80000000 \| BATU_BL_256M \| BATU_VS \| BATU_VP)

	/* Config addrs, etc */
	#define CONFIG_SYS_IBAT3L (0xF0000000 \| BATL_PP_10 \| BATL_CACHEINHIBIT)
	#define CONFIG_SYS_IBAT3U (0xF0000000 \| BATU_BL_256M \| BATU_VS \| BATU_VP)

	#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
	#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
	#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
	#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
	#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
	#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
	#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
	#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*
	* Cache Configuration
	*/
	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8240 CPU */
	#if defined(CONFIG_CMD_KGDB)
	# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif

	#endif /* __CONFIG_H */