include/configs/ep8248.h - platform/external/u-boot - Gitiles

 /*
  * Copyright (C) 2004 Arabella Software Ltd.
  * Yuli Barcohen <yuli@arabellasw.com>
  *
  * U-Boot configuration for Embedded Planet EP8248 boards.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 #define CONFIG_MPC8248
 #define CPU_ID_STR		"MPC8248"

 #define CONFIG_EP8248			/* Embedded Planet EP8248 board */

 #define	CONFIG_SYS_TEXT_BASE	0xFFF00000

 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/

 /* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
 #define CONFIG_ENV_OVERWRITE

 /*
  * Select serial console configuration
  *
  * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
  * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
  * for SCC).
  */
 #define	CONFIG_CONS_ON_SMC		/* Console is on SMC         */
 #undef  CONFIG_CONS_ON_SCC		/* It's not on SCC           */
 #undef	CONFIG_CONS_NONE		/* It's not on external UART */
 #define CONFIG_CONS_INDEX	1	/* SMC1 is used for console  */

 #define CONFIG_SYS_BCSR		0xFA000000

 /* Pass open firmware flat device tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1

 #define OF_TBCLK        (bd->bi_busfreq / 4)
 #define OF_STDOUT_PATH  "/soc/cpm/serial <at> 11a80"

 /* Select ethernet configuration */
 #undef	CONFIG_ETHER_ON_SCC		/* Ethernet is not on SCC */
 #define CONFIG_ETHER_ON_FCC		/* Ethernet is on FCC     */
 #undef	CONFIG_ETHER_NONE		/* No external Ethernet   */

 #define CONFIG_SYS_CPMFCR_RAMTYPE	0
 #define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)

 #define CONFIG_HAS_ETH0
 #define CONFIG_ETHER_ON_FCC1		1
 /* - Rx clock is CLK10
  * - Tx clock is CLK11
  * - BDs/buffers on 60x bus
  * - Full duplex
  */
 #define CONFIG_SYS_CMXFCR_MASK1	(CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
 #define CONFIG_SYS_CMXFCR_VALUE1	(CMXFCR_RF1CS_CLK10 | CMXFCR_TF1CS_CLK11)

 #define CONFIG_HAS_ETH1
 #define CONFIG_ETHER_ON_FCC2		1
 /* - Rx clock is CLK13
  * - Tx clock is CLK14
  * - BDs/buffers on 60x bus
  * - Full duplex
  */
 #define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
 #define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)

 #define CONFIG_MII			/* MII PHY management        */
 #define CONFIG_BITBANGMII		/* Bit-banged MDIO interface */
 /*
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT		0	/* Not used - implemented in BCSR */

 #define MDIO_ACTIVE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB)
 #define MDIO_TRISTATE		(*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04)
 #define MDIO_READ		(*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1)

 #define MDIO(bit)		if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x01; \
 				else	*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFE

 #define MDC(bit)		if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x02; \
 				else	*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFD

 #define MIIDELAY		udelay(1)

 #ifndef CONFIG_8260_CLKIN
 #define CONFIG_8260_CLKIN	66000000	/* in Hz */
 #endif

 #define CONFIG_BAUDRATE		38400


 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ECHO
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_IMMAP
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING


 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
 #define CONFIG_BOOTCOMMAND	"bootm FF860000"	/* autoboot command */
 #define CONFIG_BOOTARGS		"root=/dev/mtdblock1 rw mtdparts=phys:7M(root),-(root)ro"

 #if defined(CONFIG_CMD_KGDB)
 #undef	CONFIG_KGDB_ON_SMC		/* define if kgdb on SMC */
 #define CONFIG_KGDB_ON_SCC		/* define if kgdb on SCC */
 #undef	CONFIG_KGDB_NONE		/* define if kgdb on something else */
 #define CONFIG_KGDB_INDEX	1	/* which serial channel for kgdb */
 #define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port at */
 #endif

 #define CONFIG_BZIP2	/* include support for bzip2 compressed images */
 #undef	CONFIG_WATCHDOG			/* disable platform specific watchdog */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_HUSH_PARSER
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
 #define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt   */
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size  */
 #define CONFIG_SYS_MAXARGS		16		/* max number of command args */
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size  */

 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/

 #define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */

 #define CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks */

 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }

 #define CONFIG_SYS_FLASH_BASE		0xFF800000
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks	*/
 #define CONFIG_SYS_MAX_FLASH_SECT	256	/* max num of sects on one chip */

 #define	CONFIG_SYS_DIRECT_FLASH_TFTP

 #if defined(CONFIG_CMD_JFFS2)
 #define CONFIG_SYS_JFFS2_FIRST_BANK	0
 #define CONFIG_SYS_JFFS2_NUM_BANKS	CONFIG_SYS_MAX_FLASH_BANKS
 #define CONFIG_SYS_JFFS2_FIRST_SECTOR  0
 #define CONFIG_SYS_JFFS2_LAST_SECTOR   62
 #define CONFIG_SYS_JFFS2_SORT_FRAGMENTS
 #define CONFIG_SYS_JFFS_CUSTOM_PART
 #endif

 #if defined(CONFIG_CMD_I2C)
 #define CONFIG_HARD_I2C		1	/* To enable I2C support	*/
 #define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed			*/
 #define CONFIG_SYS_I2C_SLAVE		0x7F	/* I2C slave address		*/
 #endif

 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
 #endif

 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256KB for Monitor */

 #define CONFIG_ENV_IS_IN_FLASH

 #ifdef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_SECT_SIZE	0x20000
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 #endif /* CONFIG_ENV_IS_IN_FLASH */

 #define CONFIG_SYS_DEFAULT_IMMR	0x00010000

 #define CONFIG_SYS_IMMR		0xF0000000

 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
 #define CONFIG_SYS_INIT_RAM_SIZE	0x2000	/* Size of used area in DPRAM	*/
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 /* Hard reset configuration word */
 #define CONFIG_SYS_HRCW_MASTER		0x0C40025A /* Not used - provided by FPGA */
 /* No slaves */
 #define CONFIG_SYS_HRCW_SLAVE1		0
 #define CONFIG_SYS_HRCW_SLAVE2		0
 #define CONFIG_SYS_HRCW_SLAVE3		0
 #define CONFIG_SYS_HRCW_SLAVE4		0
 #define CONFIG_SYS_HRCW_SLAVE5		0
 #define CONFIG_SYS_HRCW_SLAVE6		0
 #define CONFIG_SYS_HRCW_SLAVE7		0

 #define CONFIG_SYS_MALLOC_LEN		(4096 << 10)	/* Reserve 4 MB for malloc()	*/
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

 #define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8260 CPUs */
 #if defined(CONFIG_CMD_KGDB)
 #  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif

 #define CONFIG_SYS_HID0_INIT		0
 #define CONFIG_SYS_HID0_FINAL		(HID0_ICE | HID0_IFEM | HID0_ABE)

 #define CONFIG_SYS_HID2		0

 #define CONFIG_SYS_SIUMCR		0x01240200
 #define CONFIG_SYS_SYPCR		0xFFFF0683
 #define CONFIG_SYS_BCR			0x00000000
 #define CONFIG_SYS_SCCR		SCCR_DFBRG01

 #define CONFIG_SYS_RMR			RMR_CSRE
 #define CONFIG_SYS_TMCNTSC		(TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
 #define CONFIG_SYS_PISCR		(PISCR_PS|PISCR_PTF|PISCR_PTE)
 #define CONFIG_SYS_RCCR		0

 #define CONFIG_SYS_MPTPR		0x1300
 #define CONFIG_SYS_PSDMR		0x82672522
 #define CONFIG_SYS_PSRT		0x4B

 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_SDRAM_BR		(CONFIG_SYS_SDRAM_BASE | 0x00001841)
 #define CONFIG_SYS_SDRAM_OR		0xFF0030C0

 #define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | 0x00001801)
 #define CONFIG_SYS_OR0_PRELIM		0xFF8008C2
 #define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_BCSR | 0x00000801)
 #define CONFIG_SYS_OR2_PRELIM		0xFFF00864

 #define CONFIG_SYS_RESET_ADDRESS	0xC0000000

 #endif /* __CONFIG_H */
	/*
	* Copyright (C) 2004 Arabella Software Ltd.
	* Yuli Barcohen <yuli@arabellasw.com>
	*
	* U-Boot configuration for Embedded Planet EP8248 boards.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	#define CONFIG_MPC8248
	#define CPU_ID_STR "MPC8248"

	#define CONFIG_EP8248 /* Embedded Planet EP8248 board */

	#define CONFIG_SYS_TEXT_BASE 0xFFF00000

	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */

	/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
	#define CONFIG_ENV_OVERWRITE

	/*
	* Select serial console configuration
	*
	* If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
	* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
	* for SCC).
	*/
	#define CONFIG_CONS_ON_SMC /* Console is on SMC */
	#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
	#undef CONFIG_CONS_NONE /* It's not on external UART */
	#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */

	#define CONFIG_SYS_BCSR 0xFA000000

	/* Pass open firmware flat device tree */
	#define CONFIG_OF_LIBFDT 1
	#define CONFIG_OF_BOARD_SETUP 1

	#define OF_TBCLK (bd->bi_busfreq / 4)
	#define OF_STDOUT_PATH "/soc/cpm/serial <at> 11a80"

	/* Select ethernet configuration */
	#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
	#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
	#undef CONFIG_ETHER_NONE /* No external Ethernet */

	#define CONFIG_SYS_CPMFCR_RAMTYPE 0
	#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE \| FCC_PSMR_LPB)

	#define CONFIG_HAS_ETH0
	#define CONFIG_ETHER_ON_FCC1 1
	/* - Rx clock is CLK10
	* - Tx clock is CLK11
	* - BDs/buffers on 60x bus
	* - Full duplex
	*/
	#define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1 \| CMXFCR_RF1CS_MSK \| CMXFCR_TF1CS_MSK)
	#define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK10 \| CMXFCR_TF1CS_CLK11)

	#define CONFIG_HAS_ETH1
	#define CONFIG_ETHER_ON_FCC2 1
	/* - Rx clock is CLK13
	* - Tx clock is CLK14
	* - BDs/buffers on 60x bus
	* - Full duplex
	*/
	#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 \| CMXFCR_RF2CS_MSK \| CMXFCR_TF2CS_MSK)
	#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 \| CMXFCR_TF2CS_CLK14)

	#define CONFIG_MII /* MII PHY management */
	#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */
	/*
	* GPIO pins used for bit-banged MII communications
	*/
	#define MDIO_PORT 0 /* Not used - implemented in BCSR */

	#define MDIO_ACTIVE ((vu_char )(CONFIG_SYS_BCSR + 8) &= 0xFB)
	#define MDIO_TRISTATE ((vu_char )(CONFIG_SYS_BCSR + 8) \|= 0x04)
	#define MDIO_READ ((vu_char )(CONFIG_SYS_BCSR + 8) & 1)

	#define MDIO(bit) if(bit) (vu_char )(CONFIG_SYS_BCSR + 8) \|= 0x01; \
	else (vu_char )(CONFIG_SYS_BCSR + 8) &= 0xFE

	#define MDC(bit) if(bit) (vu_char )(CONFIG_SYS_BCSR + 8) \|= 0x02; \
	else (vu_char )(CONFIG_SYS_BCSR + 8) &= 0xFD

	#define MIIDELAY udelay(1)

	#ifndef CONFIG_8260_CLKIN
	#define CONFIG_8260_CLKIN 66000000 /* in Hz */
	#endif

	#define CONFIG_BAUDRATE 38400


	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_ECHO
	#define CONFIG_CMD_I2C
	#define CONFIG_CMD_IMMAP
	#define CONFIG_CMD_MII
	#define CONFIG_CMD_PING


	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
	#define CONFIG_BOOTCOMMAND "bootm FF860000" /* autoboot command */
	#define CONFIG_BOOTARGS "root=/dev/mtdblock1 rw mtdparts=phys:7M(root),-(root)ro"

	#if defined(CONFIG_CMD_KGDB)
	#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
	#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
	#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
	#define CONFIG_KGDB_INDEX 1 /* which serial channel for kgdb */
	#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
	#endif

	#define CONFIG_BZIP2 /* include support for bzip2 compressed images */
	#undef CONFIG_WATCHDOG /* disable platform specific watchdog */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_HUSH_PARSER
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */

	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */

	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }

	#define CONFIG_SYS_FLASH_BASE 0xFF800000
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */

	#define CONFIG_SYS_DIRECT_FLASH_TFTP

	#if defined(CONFIG_CMD_JFFS2)
	#define CONFIG_SYS_JFFS2_FIRST_BANK 0
	#define CONFIG_SYS_JFFS2_NUM_BANKS CONFIG_SYS_MAX_FLASH_BANKS
	#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0
	#define CONFIG_SYS_JFFS2_LAST_SECTOR 62
	#define CONFIG_SYS_JFFS2_SORT_FRAGMENTS
	#define CONFIG_SYS_JFFS_CUSTOM_PART
	#endif

	#if defined(CONFIG_CMD_I2C)
	#define CONFIG_HARD_I2C 1 /* To enable I2C support */
	#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */
	#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */
	#endif

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	#define CONFIG_SYS_RAMBOOT
	#endif

	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */

	#define CONFIG_ENV_IS_IN_FLASH

	#ifdef CONFIG_ENV_IS_IN_FLASH
	#define CONFIG_ENV_SECT_SIZE 0x20000
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
	#endif /* CONFIG_ENV_IS_IN_FLASH */

	#define CONFIG_SYS_DEFAULT_IMMR 0x00010000

	#define CONFIG_SYS_IMMR 0xF0000000

	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
	#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	/* Hard reset configuration word */
	#define CONFIG_SYS_HRCW_MASTER 0x0C40025A /* Not used - provided by FPGA */
	/* No slaves */
	#define CONFIG_SYS_HRCW_SLAVE1 0
	#define CONFIG_SYS_HRCW_SLAVE2 0
	#define CONFIG_SYS_HRCW_SLAVE3 0
	#define CONFIG_SYS_HRCW_SLAVE4 0
	#define CONFIG_SYS_HRCW_SLAVE5 0
	#define CONFIG_SYS_HRCW_SLAVE6 0
	#define CONFIG_SYS_HRCW_SLAVE7 0

	#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
	#if defined(CONFIG_CMD_KGDB)
	# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif

	#define CONFIG_SYS_HID0_INIT 0
	#define CONFIG_SYS_HID0_FINAL (HID0_ICE \| HID0_IFEM \| HID0_ABE)

	#define CONFIG_SYS_HID2 0

	#define CONFIG_SYS_SIUMCR 0x01240200
	#define CONFIG_SYS_SYPCR 0xFFFF0683
	#define CONFIG_SYS_BCR 0x00000000
	#define CONFIG_SYS_SCCR SCCR_DFBRG01

	#define CONFIG_SYS_RMR RMR_CSRE
	#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC\|TMCNTSC_ALR\|TMCNTSC_TCF\|TMCNTSC_TCE)
	#define CONFIG_SYS_PISCR (PISCR_PS\|PISCR_PTF\|PISCR_PTE)
	#define CONFIG_SYS_RCCR 0

	#define CONFIG_SYS_MPTPR 0x1300
	#define CONFIG_SYS_PSDMR 0x82672522
	#define CONFIG_SYS_PSRT 0x4B

	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_SDRAM_BR (CONFIG_SYS_SDRAM_BASE \| 0x00001841)
	#define CONFIG_SYS_SDRAM_OR 0xFF0030C0

	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \| 0x00001801)
	#define CONFIG_SYS_OR0_PRELIM 0xFF8008C2
	#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_BCSR \| 0x00000801)
	#define CONFIG_SYS_OR2_PRELIM 0xFFF00864

	#define CONFIG_SYS_RESET_ADDRESS 0xC0000000

	#endif /* __CONFIG_H */