| /* |
| * (C) Copyright 2011 HALE electronic <helmut.raiger@hale.at> |
| * (C) Copyright 2008 Magnus Lilja <lilja.magnus@gmail.com> |
| * |
| * Configuration settings for the HALE TT-01 board. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #include <asm/arch/imx-regs.h> |
| |
| /* High Level Configuration Options */ |
| #define CONFIG_ARM1136 |
| #define CONFIG_MX31 |
| |
| #define CONFIG_DISPLAY_CPUINFO |
| #define CONFIG_DISPLAY_BOARDINFO |
| |
| #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ |
| #define CONFIG_SETUP_MEMORY_TAGS |
| #define CONFIG_INITRD_TAG |
| |
| #define CONFIG_MACH_TYPE 3726 /* not yet in mach-types.h */ |
| #define CONFIG_SYS_TEXT_BASE 0xA0000000 |
| |
| |
| /* |
| * Physical Memory Map: |
| * CS settings are defined by i.MX31: |
| * - CSD0 and CDS1 are 256MB each, starting at 0x80000000 and 0x9000000 |
| * - CS0 and CS1 are 128MB each, at A0000000 and A8000000 |
| * - CS2 to CS5 are 32MB each, at B0.., B2.., B4.., B6.. |
| * |
| * HALE set-up of the bluetechnix board for now is: |
| * - 128MB DDR (2x64MB, 2x16bit), connected to 32bit DDR ram interface |
| * - NOR-Flash (Spansion 32MB MCP, Flash+16MB PSRAM), 16bit interface at CS0 |
| * - S71WS256ND0BFWYM (and CS1 for 64MB S71WS512ND0 without PSRAM) |
| * the flash chip is a mirrorbit S29WS256N ! |
| * - the PSRAM is hooked to CS5 (0xB6000000) |
| * - Intel Strata Flash PF48F2000P0ZB00, 16bit interface at (CS0 or) CS1 |
| * - 64Mbit = 8MByte (will go away in the production set-up) |
| * - NAND-Flash NAND01GR3B2BZA6 at NAND-FC: |
| * 1Gbit=128MB, 2048+64 bytes/page, 64pages x 1024 blocks |
| * - Ethernet controller SMC9118 at CS4 via FPGA, 16bit interface |
| * |
| * u-boot will support the 32MB nor flash and the 128MB NAND flash, the PSRAM |
| * is not used right now. We should be able to reduce the SOM to NAND flash |
| * only and boot from there. |
| */ |
| #define CONFIG_NR_DRAM_BANKS 1 |
| #define PHYS_SDRAM_1 CSD0_BASE |
| #define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024) |
| |
| #define CONFIG_BOARD_EARLY_INIT_F |
| #define CONFIG_BOARD_LATE_INIT |
| |
| #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 |
| #define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR |
| #define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE |
| #define CONFIG_SYS_GBL_DATA_OFFSET \ |
| (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
| #define CONFIG_SYS_INIT_SP_ADDR \ |
| (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET) |
| |
| /* default load address, 1MB up the road */ |
| #define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1+0x100000) |
| |
| /* Size of malloc() pool, make sure possible frame buffer fits */ |
| #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 10*1024*1024) |
| |
| /* memtest works on all but the last 1MB (u-boot) and malloc area */ |
| #define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1 |
| #define CONFIG_SYS_MEMTEST_END \ |
| (PHYS_SDRAM_1+(PHYS_SDRAM_1_SIZE-CONFIG_SYS_MALLOC_LEN-0x100000)) |
| |
| /* CFI FLASH driver setup */ |
| #define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */ |
| #define CONFIG_FLASH_CFI_DRIVER /* Use drivers/cfi_flash.c */ |
| #define CONFIG_FLASH_SPANSION_S29WS_N |
| /* |
| * TODO: Bluetechnix (the supplier of the SOM) did define these values |
| * in their original version of u-boot (1.2 or so). This should be |
| * reviewed. |
| * |
| * #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| * #define CONFIG_SYS_FLASH_PROTECTION |
| */ |
| #define CONFIG_SYS_FLASH_BASE CS0_BASE |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT (254+8) /* max number of sectors per chip */ |
| |
| /* |
| * FLASH and environment organization, only the Spansion chip is supported: |
| * - it has 254 * 128kB + 8 * 32kB blocks |
| * - this setup uses 4*32k+3*128k as monitor space = 0xA000 0000 to 0xA00F FFFF |
| * and 2 sectors with 128k as environment = |
| * A010 0000 to 0xA011 FFFF and 0xA012 0000 to 0xA013 FFFF |
| * - this could be less, but this is only for developer versions of the board |
| * and no-one is going to use the NOR flash anyway. |
| * |
| * Monitor is at the beginning of the NOR-Flash, 1MB reserved. Again this is |
| * way to large, but it avoids ENV overwrite (when updating u-boot) in case |
| * size breaks the next boundary (as it has with 128k). |
| */ |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_MONITOR_LEN (1024 * 1024) |
| |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_SECT_SIZE (128 * 1024) |
| #define CONFIG_ENV_SIZE (128 * 1024) |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE |
| |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) |
| |
| /* Hardware drivers */ |
| |
| /* |
| * on TT-01 UART1 pins are used by Audio, so we use UART2 |
| * TT-01 implements a hardware that turns off components depending on |
| * the power level. In PL=1 the RS232 transceiver is usually off, |
| * make sure that the transceiver is enabled during PL=1 for testing! |
| */ |
| #define CONFIG_MXC_UART |
| #define CONFIG_MXC_UART_BASE UART2_BASE |
| |
| #define CONFIG_MXC_SPI |
| #define CONFIG_MXC_GPIO |
| |
| /* MC13783 connected to CSPI3 and SS0 */ |
| #define CONFIG_POWER |
| #define CONFIG_POWER_SPI |
| #define CONFIG_POWER_FSL |
| |
| #define CONFIG_FSL_PMIC_BUS 2 |
| #define CONFIG_FSL_PMIC_CS 0 |
| #define CONFIG_FSL_PMIC_CLK 1000000 |
| #define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH) |
| #define CONFIG_FSL_PMIC_BITLEN 32 |
| |
| #define CONFIG_RTC_MC13XXX |
| |
| /* allow to overwrite serial and ethaddr */ |
| #define CONFIG_ENV_OVERWRITE |
| /* console is UART2 on TT-01 */ |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_BAUDRATE 115200 |
| |
| /* ethernet setup for the onboard smc9118 */ |
| #define CONFIG_MII |
| #define CONFIG_SMC911X |
| /* 16 bit, onboard ethernet, decoded via MACH-MX0 FPGA at 0x84200000 */ |
| #define CONFIG_SMC911X_BASE (CS4_BASE+0x200000) |
| #define CONFIG_SMC911X_16_BIT |
| |
| /* mmc driver */ |
| #define CONFIG_MMC |
| #define CONFIG_GENERIC_MMC |
| #define CONFIG_MXC_MMC |
| #define CONFIG_MXC_MCI_REGS_BASE SDHC1_BASE_ADDR |
| |
| /* video support */ |
| #define CONFIG_VIDEO |
| #define CONFIG_VIDEO_MX3 |
| #define CONFIG_CFB_CONSOLE |
| #define CONFIG_VIDEO_LOGO |
| /* splash image won't work with NAND boot, use preboot script */ |
| #define CONFIG_VIDEO_SW_CURSOR |
| #define CONFIG_CONSOLE_EXTRA_INFO /* display additional board info */ |
| #define CONFIG_VGA_AS_SINGLE_DEVICE /* display is an output only device */ |
| |
| /* allow stdin, stdout and stderr variables to redirect output */ |
| #define CONFIG_SYS_CONSOLE_IS_IN_ENV |
| #define CONFIG_SILENT_CONSOLE /* UARTs used externally (release) */ |
| #define CONFIG_SYS_DEVICE_NULLDEV /* allow console to be turned off */ |
| #define CONFIG_PREBOOT |
| |
| /* allow decompressing max. 4MB */ |
| #define CONFIG_VIDEO_BMP_GZIP |
| /* this is not only used by cfb_console.c for the logo, but also in cmd_bmp.c */ |
| #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (4*1024*1024) |
| |
| /* |
| * Command definition |
| */ |
| |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_SAVEENV |
| #define CONFIG_CMD_NAND |
| /* |
| * #define CONFIG_CMD_NAND_LOCK_UNLOCK the NAND01... chip does not support |
| * the NAND_CMD_LOCK_STATUS command, however the NFC of i.MX31 supports |
| * a software locking scheme. |
| */ |
| #define CONFIG_CMD_BMP |
| |
| #define CONFIG_BOOTDELAY 3 |
| |
| /* |
| * currently a default setting for booting via script is implemented |
| * set user to login name and serverip to tftp host, define your |
| * boot behaviour in bootscript.loginname |
| * |
| * TT-01 board specific TFT setup (used by drivers/video/mx3fb.c) |
| * |
| * This set-up is for the L5F30947T04 by Epson, which is |
| * 800x480, 33MHz pixel clock, 60Hz vsync, 31.6kHz hsync |
| * sync must be set to: DI_D3_DRDY_SHARP_POL | DI_D3_CLK_POL |
| */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "videomode=epson\0" \ |
| "epson=video=ctfb:x:800,y:480,depth:16,mode:0,pclk:30076," \ |
| "le:215,ri:1,up:32,lo:13,hs:7,vs:10,sync:100663296,vmode:0\0" \ |
| "bootcmd=dhcp bootscript.${user}; source\0" |
| |
| #define CONFIG_BOOTP_SERVERIP /* tftp serverip not overruled by dhcp server */ |
| #define CONFIG_BOOTP_SEND_HOSTNAME /* if env-var 'hostname' is set, send it */ |
| |
| /* Miscellaneous configurable options */ |
| #define CONFIG_SYS_HUSH_PARSER |
| |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_PROMPT "TT01> " |
| #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
| /* Print Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ |
| sizeof(CONFIG_SYS_PROMPT)+16) |
| /* max number of command args */ |
| #define CONFIG_SYS_MAXARGS 16 |
| /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE |
| |
| #define CONFIG_SYS_HZ 1000 |
| |
| #define CONFIG_CMDLINE_EDITING |
| |
| /* MMC boot support */ |
| #define CONFIG_CMD_MMC |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_EFI_PARTITION |
| #define CONFIG_CMD_EXT2 |
| #define CONFIG_CMD_FAT |
| |
| #define CONFIG_NAND_MXC |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| |
| /* |
| * actually this is nothing someone wants to configure! |
| * CONFIG_SYS_NAND_BASE despite being passed to board_nand_init() |
| * is not used by the driver. |
| */ |
| #define CONFIG_MXC_NAND_REGS_BASE NFC_BASE_ADDR |
| #define CONFIG_SYS_NAND_BASE NFC_BASE_ADDR |
| #define CONFIG_MXC_NAND_HWECC |
| |
| /* the current u-boot driver does not use the nand flash setup! */ |
| #define CONFIG_SYS_NAND_LARGEPAGE |
| /* |
| * it's not 16 bit: |
| * #define CONFIG_SYS_NAND_BUSWIDTH_16BIT |
| * the current u-boot mxc_nand.c tries to auto-detect, but this only |
| * reads the boot settings during reset (which might be wrong) |
| */ |
| |
| #endif /* __CONFIG_H */ |