| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (C) 2016, STMicroelectronics - All Rights Reserved |
| * Author(s): Vikas Manocha, <vikas.manocha@st.com> for STMicroelectronics. |
| */ |
| |
| #include <common.h> |
| #include <clk.h> |
| #include <dm.h> |
| #include <serial.h> |
| #include <watchdog.h> |
| #include <asm/io.h> |
| #include <asm/arch/stm32.h> |
| #include "serial_stm32.h" |
| |
| static void _stm32_serial_setbrg(fdt_addr_t base, |
| struct stm32_uart_info *uart_info, |
| u32 clock_rate, |
| int baudrate) |
| { |
| bool stm32f4 = uart_info->stm32f4; |
| u32 int_div, mantissa, fraction, oversampling; |
| |
| int_div = DIV_ROUND_CLOSEST(clock_rate, baudrate); |
| |
| if (int_div < 16) { |
| oversampling = 8; |
| setbits_le32(base + CR1_OFFSET(stm32f4), USART_CR1_OVER8); |
| } else { |
| oversampling = 16; |
| clrbits_le32(base + CR1_OFFSET(stm32f4), USART_CR1_OVER8); |
| } |
| |
| mantissa = (int_div / oversampling) << USART_BRR_M_SHIFT; |
| fraction = int_div % oversampling; |
| |
| writel(mantissa | fraction, base + BRR_OFFSET(stm32f4)); |
| } |
| |
| static int stm32_serial_setbrg(struct udevice *dev, int baudrate) |
| { |
| struct stm32x7_serial_platdata *plat = dev_get_platdata(dev); |
| |
| _stm32_serial_setbrg(plat->base, plat->uart_info, |
| plat->clock_rate, baudrate); |
| |
| return 0; |
| } |
| |
| static int stm32_serial_setconfig(struct udevice *dev, uint serial_config) |
| { |
| struct stm32x7_serial_platdata *plat = dev_get_platdata(dev); |
| bool stm32f4 = plat->uart_info->stm32f4; |
| u8 uart_enable_bit = plat->uart_info->uart_enable_bit; |
| u32 cr1 = plat->base + CR1_OFFSET(stm32f4); |
| u32 config = 0; |
| uint parity = SERIAL_GET_PARITY(serial_config); |
| uint bits = SERIAL_GET_BITS(serial_config); |
| uint stop = SERIAL_GET_STOP(serial_config); |
| |
| /* |
| * only parity config is implemented, check if other serial settings |
| * are the default one. |
| * (STM32F4 serial IP didn't support parity setting) |
| */ |
| if (bits != SERIAL_8_BITS || stop != SERIAL_ONE_STOP || stm32f4) |
| return -ENOTSUPP; /* not supported in driver*/ |
| |
| clrbits_le32(cr1, USART_CR1_RE | USART_CR1_TE | BIT(uart_enable_bit)); |
| /* update usart configuration (uart need to be disable) |
| * PCE: parity check enable |
| * PS : '0' : Even / '1' : Odd |
| * M[1:0] = '00' : 8 Data bits |
| * M[1:0] = '01' : 9 Data bits with parity |
| */ |
| switch (parity) { |
| default: |
| case SERIAL_PAR_NONE: |
| config = 0; |
| break; |
| case SERIAL_PAR_ODD: |
| config = USART_CR1_PCE | USART_CR1_PS | USART_CR1_M0; |
| break; |
| case SERIAL_PAR_EVEN: |
| config = USART_CR1_PCE | USART_CR1_M0; |
| break; |
| } |
| |
| clrsetbits_le32(cr1, |
| USART_CR1_PCE | USART_CR1_PS | USART_CR1_M1 | |
| USART_CR1_M0, |
| config); |
| setbits_le32(cr1, USART_CR1_RE | USART_CR1_TE | BIT(uart_enable_bit)); |
| |
| return 0; |
| } |
| |
| static int stm32_serial_getc(struct udevice *dev) |
| { |
| struct stm32x7_serial_platdata *plat = dev_get_platdata(dev); |
| bool stm32f4 = plat->uart_info->stm32f4; |
| fdt_addr_t base = plat->base; |
| u32 isr = readl(base + ISR_OFFSET(stm32f4)); |
| |
| if ((isr & USART_ISR_RXNE) == 0) |
| return -EAGAIN; |
| |
| if (isr & (USART_ISR_PE | USART_ISR_ORE)) { |
| if (!stm32f4) |
| setbits_le32(base + ICR_OFFSET, |
| USART_ICR_PCECF | USART_ICR_ORECF); |
| else |
| readl(base + RDR_OFFSET(stm32f4)); |
| return -EIO; |
| } |
| |
| return readl(base + RDR_OFFSET(stm32f4)); |
| } |
| |
| static int _stm32_serial_putc(fdt_addr_t base, |
| struct stm32_uart_info *uart_info, |
| const char c) |
| { |
| bool stm32f4 = uart_info->stm32f4; |
| |
| if ((readl(base + ISR_OFFSET(stm32f4)) & USART_ISR_TXE) == 0) |
| return -EAGAIN; |
| |
| writel(c, base + TDR_OFFSET(stm32f4)); |
| |
| return 0; |
| } |
| |
| static int stm32_serial_putc(struct udevice *dev, const char c) |
| { |
| struct stm32x7_serial_platdata *plat = dev_get_platdata(dev); |
| |
| return _stm32_serial_putc(plat->base, plat->uart_info, c); |
| } |
| |
| static int stm32_serial_pending(struct udevice *dev, bool input) |
| { |
| struct stm32x7_serial_platdata *plat = dev_get_platdata(dev); |
| bool stm32f4 = plat->uart_info->stm32f4; |
| fdt_addr_t base = plat->base; |
| |
| if (input) |
| return readl(base + ISR_OFFSET(stm32f4)) & |
| USART_ISR_RXNE ? 1 : 0; |
| else |
| return readl(base + ISR_OFFSET(stm32f4)) & |
| USART_ISR_TXE ? 0 : 1; |
| } |
| |
| static void _stm32_serial_init(fdt_addr_t base, |
| struct stm32_uart_info *uart_info) |
| { |
| bool stm32f4 = uart_info->stm32f4; |
| u8 uart_enable_bit = uart_info->uart_enable_bit; |
| |
| /* Disable uart-> enable fifo -> enable uart */ |
| clrbits_le32(base + CR1_OFFSET(stm32f4), USART_CR1_RE | USART_CR1_TE | |
| BIT(uart_enable_bit)); |
| if (uart_info->has_fifo) |
| setbits_le32(base + CR1_OFFSET(stm32f4), USART_CR1_FIFOEN); |
| setbits_le32(base + CR1_OFFSET(stm32f4), USART_CR1_RE | USART_CR1_TE | |
| BIT(uart_enable_bit)); |
| } |
| |
| static int stm32_serial_probe(struct udevice *dev) |
| { |
| struct stm32x7_serial_platdata *plat = dev_get_platdata(dev); |
| struct clk clk; |
| int ret; |
| |
| plat->uart_info = (struct stm32_uart_info *)dev_get_driver_data(dev); |
| |
| ret = clk_get_by_index(dev, 0, &clk); |
| if (ret < 0) |
| return ret; |
| |
| ret = clk_enable(&clk); |
| if (ret) { |
| dev_err(dev, "failed to enable clock\n"); |
| return ret; |
| } |
| |
| plat->clock_rate = clk_get_rate(&clk); |
| if (plat->clock_rate < 0) { |
| clk_disable(&clk); |
| return plat->clock_rate; |
| }; |
| |
| _stm32_serial_init(plat->base, plat->uart_info); |
| |
| return 0; |
| } |
| |
| static const struct udevice_id stm32_serial_id[] = { |
| { .compatible = "st,stm32-uart", .data = (ulong)&stm32f4_info}, |
| { .compatible = "st,stm32f7-uart", .data = (ulong)&stm32f7_info}, |
| { .compatible = "st,stm32h7-uart", .data = (ulong)&stm32h7_info}, |
| {} |
| }; |
| |
| static int stm32_serial_ofdata_to_platdata(struct udevice *dev) |
| { |
| struct stm32x7_serial_platdata *plat = dev_get_platdata(dev); |
| |
| plat->base = devfdt_get_addr(dev); |
| if (plat->base == FDT_ADDR_T_NONE) |
| return -EINVAL; |
| |
| return 0; |
| } |
| |
| static const struct dm_serial_ops stm32_serial_ops = { |
| .putc = stm32_serial_putc, |
| .pending = stm32_serial_pending, |
| .getc = stm32_serial_getc, |
| .setbrg = stm32_serial_setbrg, |
| .setconfig = stm32_serial_setconfig |
| }; |
| |
| U_BOOT_DRIVER(serial_stm32) = { |
| .name = "serial_stm32", |
| .id = UCLASS_SERIAL, |
| .of_match = of_match_ptr(stm32_serial_id), |
| .ofdata_to_platdata = of_match_ptr(stm32_serial_ofdata_to_platdata), |
| .platdata_auto_alloc_size = sizeof(struct stm32x7_serial_platdata), |
| .ops = &stm32_serial_ops, |
| .probe = stm32_serial_probe, |
| #if !CONFIG_IS_ENABLED(OF_CONTROL) |
| .flags = DM_FLAG_PRE_RELOC, |
| #endif |
| }; |
| |
| #ifdef CONFIG_DEBUG_UART_STM32 |
| #include <debug_uart.h> |
| static inline struct stm32_uart_info *_debug_uart_info(void) |
| { |
| struct stm32_uart_info *uart_info; |
| |
| #if defined(CONFIG_STM32F4) |
| uart_info = &stm32f4_info; |
| #elif defined(CONFIG_STM32F7) |
| uart_info = &stm32f7_info; |
| #else |
| uart_info = &stm32h7_info; |
| #endif |
| return uart_info; |
| } |
| |
| static inline void _debug_uart_init(void) |
| { |
| fdt_addr_t base = CONFIG_DEBUG_UART_BASE; |
| struct stm32_uart_info *uart_info = _debug_uart_info(); |
| |
| _stm32_serial_init(base, uart_info); |
| _stm32_serial_setbrg(base, uart_info, |
| CONFIG_DEBUG_UART_CLOCK, |
| CONFIG_BAUDRATE); |
| printf("DEBUG done\n"); |
| } |
| |
| static inline void _debug_uart_putc(int c) |
| { |
| fdt_addr_t base = CONFIG_DEBUG_UART_BASE; |
| struct stm32_uart_info *uart_info = _debug_uart_info(); |
| |
| while (_stm32_serial_putc(base, uart_info, c) == -EAGAIN) |
| WATCHDOG_RESET(); |
| } |
| |
| DEBUG_UART_FUNCS |
| #endif |