| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Copyright (C) 2012 Atmel Corporation |
| * |
| * Configuation settings for the AT91SAM9X5EK board. |
| */ |
| |
| #ifndef __CONFIG_H__ |
| #define __CONFIG_H__ |
| |
| /* ARM asynchronous clock */ |
| #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 |
| #define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */ |
| |
| /* general purpose I/O */ |
| #define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| |
| /* |
| * define CONFIG_USB_EHCI_HCD to enable USB Hi-Speed (aka 2.0) |
| * NB: in this case, USB 1.1 devices won't be recognized. |
| */ |
| |
| /* SDRAM */ |
| #define CONFIG_SYS_SDRAM_BASE 0x20000000 |
| #define CONFIG_SYS_SDRAM_SIZE 0x08000000 /* 128 megs */ |
| |
| #define CONFIG_SYS_INIT_SP_ADDR \ |
| (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) |
| |
| /* DataFlash */ |
| |
| /* NAND flash */ |
| #ifdef CONFIG_CMD_NAND |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE 0x40000000 |
| #define CONFIG_SYS_NAND_DBW_8 1 |
| /* our ALE is AD21 */ |
| #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) |
| /* our CLE is AD22 */ |
| #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) |
| #define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PD4 |
| #define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PD5 |
| #endif |
| |
| /* USB */ |
| #ifdef CONFIG_CMD_USB |
| #ifndef CONFIG_USB_EHCI_HCD |
| #define CONFIG_USB_ATMEL |
| #define CONFIG_USB_ATMEL_CLK_SEL_UPLL |
| #define CONFIG_USB_OHCI_NEW |
| #define CONFIG_SYS_USB_OHCI_CPU_INIT |
| #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI |
| #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9x5" |
| #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3 |
| #endif |
| #endif |
| |
| #ifdef CONFIG_NAND_BOOT |
| /* bootstrap + u-boot + env + linux in nandflash */ |
| #define CONFIG_BOOTCOMMAND "nand read " \ |
| "0x22000000 0x200000 0x600000; " \ |
| "nand read 0x21000000 0x180000 0x20000; " \ |
| "bootz 0x22000000 - 0x21000000" |
| #elif defined(CONFIG_SPI_BOOT) |
| /* bootstrap + u-boot + env + linux in spi flash */ |
| #define CONFIG_BOOTCOMMAND "sf probe 0; " \ |
| "sf read 0x22000000 0x100000 0x300000; " \ |
| "bootm 0x22000000" |
| #elif defined(CONFIG_SYS_USE_DATAFLASH) |
| /* bootstrap + u-boot + env + linux in data flash */ |
| #define CONFIG_BOOTCOMMAND "sf probe 0; " \ |
| "sf read 0x22000000 0x84000 0x294000; " \ |
| "bootm 0x22000000" |
| #endif |
| |
| /* SPL */ |
| #define CONFIG_SPL_MAX_SIZE 0x6000 |
| #define CONFIG_SPL_STACK 0x308000 |
| |
| #define CONFIG_SPL_BSS_START_ADDR 0x20000000 |
| #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 |
| #define CONFIG_SYS_SPL_MALLOC_START 0x20080000 |
| #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 |
| |
| #define CONFIG_SYS_MONITOR_LEN (512 << 10) |
| |
| #define CONFIG_SYS_MASTER_CLOCK 132096000 |
| #define CONFIG_SYS_AT91_PLLA 0x20c73f03 |
| #define CONFIG_SYS_MCKR 0x1301 |
| #define CONFIG_SYS_MCKR_CSS 0x1302 |
| |
| #ifdef CONFIG_SD_BOOT |
| #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" |
| #endif |
| #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 |
| #define CONFIG_SYS_NAND_5_ADDR_CYCLE |
| #define CONFIG_SYS_NAND_PAGE_SIZE 0x800 |
| #define CONFIG_SYS_NAND_PAGE_COUNT 64 |
| #define CONFIG_SYS_NAND_OOBSIZE 64 |
| #define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 |
| #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 |
| |
| #endif |