| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * (C) Copyright 2007-2011 |
| * Allwinner Technology Co., Ltd. <www.allwinnertech.com> |
| * Aaron <leafy.myeh@allwinnertech.com> |
| * |
| * MMC driver for allwinner sunxi platform. |
| */ |
| |
| #include <common.h> |
| #include <dm.h> |
| #include <errno.h> |
| #include <log.h> |
| #include <malloc.h> |
| #include <mmc.h> |
| #include <clk.h> |
| #include <reset.h> |
| #include <asm/io.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/cpu.h> |
| #include <asm/arch/gpio.h> |
| #include <asm/arch/mmc.h> |
| #include <asm-generic/gpio.h> |
| #include <linux/delay.h> |
| |
| struct sunxi_mmc_plat { |
| struct mmc_config cfg; |
| struct mmc mmc; |
| }; |
| |
| struct sunxi_mmc_priv { |
| unsigned mmc_no; |
| uint32_t *mclkreg; |
| unsigned fatal_err; |
| struct gpio_desc cd_gpio; /* Change Detect GPIO */ |
| int cd_inverted; /* Inverted Card Detect */ |
| struct sunxi_mmc *reg; |
| struct mmc_config cfg; |
| }; |
| |
| #if !CONFIG_IS_ENABLED(DM_MMC) |
| /* support 4 mmc hosts */ |
| struct sunxi_mmc_priv mmc_host[4]; |
| |
| static int sunxi_mmc_getcd_gpio(int sdc_no) |
| { |
| switch (sdc_no) { |
| case 0: return sunxi_name_to_gpio(CONFIG_MMC0_CD_PIN); |
| case 1: return sunxi_name_to_gpio(CONFIG_MMC1_CD_PIN); |
| case 2: return sunxi_name_to_gpio(CONFIG_MMC2_CD_PIN); |
| case 3: return sunxi_name_to_gpio(CONFIG_MMC3_CD_PIN); |
| } |
| return -EINVAL; |
| } |
| |
| static int mmc_resource_init(int sdc_no) |
| { |
| struct sunxi_mmc_priv *priv = &mmc_host[sdc_no]; |
| struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE; |
| int cd_pin, ret = 0; |
| |
| debug("init mmc %d resource\n", sdc_no); |
| |
| switch (sdc_no) { |
| case 0: |
| priv->reg = (struct sunxi_mmc *)SUNXI_MMC0_BASE; |
| priv->mclkreg = &ccm->sd0_clk_cfg; |
| break; |
| case 1: |
| priv->reg = (struct sunxi_mmc *)SUNXI_MMC1_BASE; |
| priv->mclkreg = &ccm->sd1_clk_cfg; |
| break; |
| case 2: |
| priv->reg = (struct sunxi_mmc *)SUNXI_MMC2_BASE; |
| priv->mclkreg = &ccm->sd2_clk_cfg; |
| break; |
| #ifdef SUNXI_MMC3_BASE |
| case 3: |
| priv->reg = (struct sunxi_mmc *)SUNXI_MMC3_BASE; |
| priv->mclkreg = &ccm->sd3_clk_cfg; |
| break; |
| #endif |
| default: |
| printf("Wrong mmc number %d\n", sdc_no); |
| return -1; |
| } |
| priv->mmc_no = sdc_no; |
| |
| cd_pin = sunxi_mmc_getcd_gpio(sdc_no); |
| if (cd_pin >= 0) { |
| ret = gpio_request(cd_pin, "mmc_cd"); |
| if (!ret) { |
| sunxi_gpio_set_pull(cd_pin, SUNXI_GPIO_PULL_UP); |
| ret = gpio_direction_input(cd_pin); |
| } |
| } |
| |
| return ret; |
| } |
| #endif |
| |
| static int mmc_set_mod_clk(struct sunxi_mmc_priv *priv, unsigned int hz) |
| { |
| unsigned int pll, pll_hz, div, n, oclk_dly, sclk_dly; |
| bool new_mode = true; |
| bool calibrate = false; |
| u32 val = 0; |
| |
| if (!IS_ENABLED(CONFIG_MMC_SUNXI_HAS_NEW_MODE)) |
| new_mode = false; |
| |
| /* A83T support new mode only on eMMC */ |
| if (IS_ENABLED(CONFIG_MACH_SUN8I_A83T) && priv->mmc_no != 2) |
| new_mode = false; |
| |
| #if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_SUN50I_GEN_H6) |
| calibrate = true; |
| #endif |
| |
| if (hz <= 24000000) { |
| pll = CCM_MMC_CTRL_OSCM24; |
| pll_hz = 24000000; |
| } else { |
| #ifdef CONFIG_MACH_SUN9I |
| pll = CCM_MMC_CTRL_PLL_PERIPH0; |
| pll_hz = clock_get_pll4_periph0(); |
| #elif defined(CONFIG_SUN50I_GEN_H6) |
| pll = CCM_MMC_CTRL_PLL6X2; |
| pll_hz = clock_get_pll6() * 2; |
| #else |
| pll = CCM_MMC_CTRL_PLL6; |
| pll_hz = clock_get_pll6(); |
| #endif |
| } |
| |
| div = pll_hz / hz; |
| if (pll_hz % hz) |
| div++; |
| |
| n = 0; |
| while (div > 16) { |
| n++; |
| div = (div + 1) / 2; |
| } |
| |
| if (n > 3) { |
| printf("mmc %u error cannot set clock to %u\n", priv->mmc_no, |
| hz); |
| return -1; |
| } |
| |
| /* determine delays */ |
| if (hz <= 400000) { |
| oclk_dly = 0; |
| sclk_dly = 0; |
| } else if (hz <= 25000000) { |
| oclk_dly = 0; |
| sclk_dly = 5; |
| #ifdef CONFIG_MACH_SUN9I |
| } else if (hz <= 52000000) { |
| oclk_dly = 5; |
| sclk_dly = 4; |
| } else { |
| /* hz > 52000000 */ |
| oclk_dly = 2; |
| sclk_dly = 4; |
| #else |
| } else if (hz <= 52000000) { |
| oclk_dly = 3; |
| sclk_dly = 4; |
| } else { |
| /* hz > 52000000 */ |
| oclk_dly = 1; |
| sclk_dly = 4; |
| #endif |
| } |
| |
| if (new_mode) { |
| #ifdef CONFIG_MMC_SUNXI_HAS_NEW_MODE |
| #ifdef CONFIG_MMC_SUNXI_HAS_MODE_SWITCH |
| val = CCM_MMC_CTRL_MODE_SEL_NEW; |
| #endif |
| setbits_le32(&priv->reg->ntsr, SUNXI_MMC_NTSR_MODE_SEL_NEW); |
| #endif |
| } else if (!calibrate) { |
| /* |
| * Use hardcoded delay values if controller doesn't support |
| * calibration |
| */ |
| val = CCM_MMC_CTRL_OCLK_DLY(oclk_dly) | |
| CCM_MMC_CTRL_SCLK_DLY(sclk_dly); |
| } |
| |
| writel(CCM_MMC_CTRL_ENABLE| pll | CCM_MMC_CTRL_N(n) | |
| CCM_MMC_CTRL_M(div) | val, priv->mclkreg); |
| |
| debug("mmc %u set mod-clk req %u parent %u n %u m %u rate %u\n", |
| priv->mmc_no, hz, pll_hz, 1u << n, div, pll_hz / (1u << n) / div); |
| |
| return 0; |
| } |
| |
| static int mmc_update_clk(struct sunxi_mmc_priv *priv) |
| { |
| unsigned int cmd; |
| unsigned timeout_msecs = 2000; |
| unsigned long start = get_timer(0); |
| |
| cmd = SUNXI_MMC_CMD_START | |
| SUNXI_MMC_CMD_UPCLK_ONLY | |
| SUNXI_MMC_CMD_WAIT_PRE_OVER; |
| |
| writel(cmd, &priv->reg->cmd); |
| while (readl(&priv->reg->cmd) & SUNXI_MMC_CMD_START) { |
| if (get_timer(start) > timeout_msecs) |
| return -1; |
| } |
| |
| /* clock update sets various irq status bits, clear these */ |
| writel(readl(&priv->reg->rint), &priv->reg->rint); |
| |
| return 0; |
| } |
| |
| static int mmc_config_clock(struct sunxi_mmc_priv *priv, struct mmc *mmc) |
| { |
| unsigned rval = readl(&priv->reg->clkcr); |
| |
| /* Disable Clock */ |
| rval &= ~SUNXI_MMC_CLK_ENABLE; |
| writel(rval, &priv->reg->clkcr); |
| if (mmc_update_clk(priv)) |
| return -1; |
| |
| /* Set mod_clk to new rate */ |
| if (mmc_set_mod_clk(priv, mmc->clock)) |
| return -1; |
| |
| /* Clear internal divider */ |
| rval &= ~SUNXI_MMC_CLK_DIVIDER_MASK; |
| writel(rval, &priv->reg->clkcr); |
| |
| #if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_SUN50I_GEN_H6) |
| /* A64 supports calibration of delays on MMC controller and we |
| * have to set delay of zero before starting calibration. |
| * Allwinner BSP driver sets a delay only in the case of |
| * using HS400 which is not supported by mainline U-Boot or |
| * Linux at the moment |
| */ |
| writel(SUNXI_MMC_CAL_DL_SW_EN, &priv->reg->samp_dl); |
| #endif |
| |
| /* Re-enable Clock */ |
| rval |= SUNXI_MMC_CLK_ENABLE; |
| writel(rval, &priv->reg->clkcr); |
| if (mmc_update_clk(priv)) |
| return -1; |
| |
| return 0; |
| } |
| |
| static int sunxi_mmc_set_ios_common(struct sunxi_mmc_priv *priv, |
| struct mmc *mmc) |
| { |
| debug("set ios: bus_width: %x, clock: %d\n", |
| mmc->bus_width, mmc->clock); |
| |
| /* Change clock first */ |
| if (mmc->clock && mmc_config_clock(priv, mmc) != 0) { |
| priv->fatal_err = 1; |
| return -EINVAL; |
| } |
| |
| /* Change bus width */ |
| if (mmc->bus_width == 8) |
| writel(0x2, &priv->reg->width); |
| else if (mmc->bus_width == 4) |
| writel(0x1, &priv->reg->width); |
| else |
| writel(0x0, &priv->reg->width); |
| |
| return 0; |
| } |
| |
| #if !CONFIG_IS_ENABLED(DM_MMC) |
| static int sunxi_mmc_core_init(struct mmc *mmc) |
| { |
| struct sunxi_mmc_priv *priv = mmc->priv; |
| |
| /* Reset controller */ |
| writel(SUNXI_MMC_GCTRL_RESET, &priv->reg->gctrl); |
| udelay(1000); |
| |
| return 0; |
| } |
| #endif |
| |
| static int mmc_trans_data_by_cpu(struct sunxi_mmc_priv *priv, struct mmc *mmc, |
| struct mmc_data *data) |
| { |
| const int reading = !!(data->flags & MMC_DATA_READ); |
| const uint32_t status_bit = reading ? SUNXI_MMC_STATUS_FIFO_EMPTY : |
| SUNXI_MMC_STATUS_FIFO_FULL; |
| unsigned i; |
| unsigned *buff = (unsigned int *)(reading ? data->dest : data->src); |
| unsigned byte_cnt = data->blocksize * data->blocks; |
| unsigned timeout_msecs = byte_cnt >> 8; |
| unsigned long start; |
| |
| if (timeout_msecs < 2000) |
| timeout_msecs = 2000; |
| |
| /* Always read / write data through the CPU */ |
| setbits_le32(&priv->reg->gctrl, SUNXI_MMC_GCTRL_ACCESS_BY_AHB); |
| |
| start = get_timer(0); |
| |
| for (i = 0; i < (byte_cnt >> 2); i++) { |
| while (readl(&priv->reg->status) & status_bit) { |
| if (get_timer(start) > timeout_msecs) |
| return -1; |
| } |
| |
| if (reading) |
| buff[i] = readl(&priv->reg->fifo); |
| else |
| writel(buff[i], &priv->reg->fifo); |
| } |
| |
| return 0; |
| } |
| |
| static int mmc_rint_wait(struct sunxi_mmc_priv *priv, struct mmc *mmc, |
| uint timeout_msecs, uint done_bit, const char *what) |
| { |
| unsigned int status; |
| unsigned long start = get_timer(0); |
| |
| do { |
| status = readl(&priv->reg->rint); |
| if ((get_timer(start) > timeout_msecs) || |
| (status & SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT)) { |
| debug("%s timeout %x\n", what, |
| status & SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT); |
| return -ETIMEDOUT; |
| } |
| } while (!(status & done_bit)); |
| |
| return 0; |
| } |
| |
| static int sunxi_mmc_send_cmd_common(struct sunxi_mmc_priv *priv, |
| struct mmc *mmc, struct mmc_cmd *cmd, |
| struct mmc_data *data) |
| { |
| unsigned int cmdval = SUNXI_MMC_CMD_START; |
| unsigned int timeout_msecs; |
| int error = 0; |
| unsigned int status = 0; |
| unsigned int bytecnt = 0; |
| |
| if (priv->fatal_err) |
| return -1; |
| if (cmd->resp_type & MMC_RSP_BUSY) |
| debug("mmc cmd %d check rsp busy\n", cmd->cmdidx); |
| if (cmd->cmdidx == 12) |
| return 0; |
| |
| if (!cmd->cmdidx) |
| cmdval |= SUNXI_MMC_CMD_SEND_INIT_SEQ; |
| if (cmd->resp_type & MMC_RSP_PRESENT) |
| cmdval |= SUNXI_MMC_CMD_RESP_EXPIRE; |
| if (cmd->resp_type & MMC_RSP_136) |
| cmdval |= SUNXI_MMC_CMD_LONG_RESPONSE; |
| if (cmd->resp_type & MMC_RSP_CRC) |
| cmdval |= SUNXI_MMC_CMD_CHK_RESPONSE_CRC; |
| |
| if (data) { |
| if ((u32)(long)data->dest & 0x3) { |
| error = -1; |
| goto out; |
| } |
| |
| cmdval |= SUNXI_MMC_CMD_DATA_EXPIRE|SUNXI_MMC_CMD_WAIT_PRE_OVER; |
| if (data->flags & MMC_DATA_WRITE) |
| cmdval |= SUNXI_MMC_CMD_WRITE; |
| if (data->blocks > 1) |
| cmdval |= SUNXI_MMC_CMD_AUTO_STOP; |
| writel(data->blocksize, &priv->reg->blksz); |
| writel(data->blocks * data->blocksize, &priv->reg->bytecnt); |
| } |
| |
| debug("mmc %d, cmd %d(0x%08x), arg 0x%08x\n", priv->mmc_no, |
| cmd->cmdidx, cmdval | cmd->cmdidx, cmd->cmdarg); |
| writel(cmd->cmdarg, &priv->reg->arg); |
| |
| if (!data) |
| writel(cmdval | cmd->cmdidx, &priv->reg->cmd); |
| |
| /* |
| * transfer data and check status |
| * STATREG[2] : FIFO empty |
| * STATREG[3] : FIFO full |
| */ |
| if (data) { |
| int ret = 0; |
| |
| bytecnt = data->blocksize * data->blocks; |
| debug("trans data %d bytes\n", bytecnt); |
| writel(cmdval | cmd->cmdidx, &priv->reg->cmd); |
| ret = mmc_trans_data_by_cpu(priv, mmc, data); |
| if (ret) { |
| error = readl(&priv->reg->rint) & |
| SUNXI_MMC_RINT_INTERRUPT_ERROR_BIT; |
| error = -ETIMEDOUT; |
| goto out; |
| } |
| } |
| |
| error = mmc_rint_wait(priv, mmc, 1000, SUNXI_MMC_RINT_COMMAND_DONE, |
| "cmd"); |
| if (error) |
| goto out; |
| |
| if (data) { |
| timeout_msecs = 120; |
| debug("cacl timeout %x msec\n", timeout_msecs); |
| error = mmc_rint_wait(priv, mmc, timeout_msecs, |
| data->blocks > 1 ? |
| SUNXI_MMC_RINT_AUTO_COMMAND_DONE : |
| SUNXI_MMC_RINT_DATA_OVER, |
| "data"); |
| if (error) |
| goto out; |
| } |
| |
| if (cmd->resp_type & MMC_RSP_BUSY) { |
| unsigned long start = get_timer(0); |
| timeout_msecs = 2000; |
| |
| do { |
| status = readl(&priv->reg->status); |
| if (get_timer(start) > timeout_msecs) { |
| debug("busy timeout\n"); |
| error = -ETIMEDOUT; |
| goto out; |
| } |
| } while (status & SUNXI_MMC_STATUS_CARD_DATA_BUSY); |
| } |
| |
| if (cmd->resp_type & MMC_RSP_136) { |
| cmd->response[0] = readl(&priv->reg->resp3); |
| cmd->response[1] = readl(&priv->reg->resp2); |
| cmd->response[2] = readl(&priv->reg->resp1); |
| cmd->response[3] = readl(&priv->reg->resp0); |
| debug("mmc resp 0x%08x 0x%08x 0x%08x 0x%08x\n", |
| cmd->response[3], cmd->response[2], |
| cmd->response[1], cmd->response[0]); |
| } else { |
| cmd->response[0] = readl(&priv->reg->resp0); |
| debug("mmc resp 0x%08x\n", cmd->response[0]); |
| } |
| out: |
| if (error < 0) { |
| writel(SUNXI_MMC_GCTRL_RESET, &priv->reg->gctrl); |
| mmc_update_clk(priv); |
| } |
| writel(0xffffffff, &priv->reg->rint); |
| writel(readl(&priv->reg->gctrl) | SUNXI_MMC_GCTRL_FIFO_RESET, |
| &priv->reg->gctrl); |
| |
| return error; |
| } |
| |
| #if !CONFIG_IS_ENABLED(DM_MMC) |
| static int sunxi_mmc_set_ios_legacy(struct mmc *mmc) |
| { |
| struct sunxi_mmc_priv *priv = mmc->priv; |
| |
| return sunxi_mmc_set_ios_common(priv, mmc); |
| } |
| |
| static int sunxi_mmc_send_cmd_legacy(struct mmc *mmc, struct mmc_cmd *cmd, |
| struct mmc_data *data) |
| { |
| struct sunxi_mmc_priv *priv = mmc->priv; |
| |
| return sunxi_mmc_send_cmd_common(priv, mmc, cmd, data); |
| } |
| |
| static int sunxi_mmc_getcd_legacy(struct mmc *mmc) |
| { |
| struct sunxi_mmc_priv *priv = mmc->priv; |
| int cd_pin; |
| |
| cd_pin = sunxi_mmc_getcd_gpio(priv->mmc_no); |
| if (cd_pin < 0) |
| return 1; |
| |
| return !gpio_get_value(cd_pin); |
| } |
| |
| static const struct mmc_ops sunxi_mmc_ops = { |
| .send_cmd = sunxi_mmc_send_cmd_legacy, |
| .set_ios = sunxi_mmc_set_ios_legacy, |
| .init = sunxi_mmc_core_init, |
| .getcd = sunxi_mmc_getcd_legacy, |
| }; |
| |
| struct mmc *sunxi_mmc_init(int sdc_no) |
| { |
| struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE; |
| struct sunxi_mmc_priv *priv = &mmc_host[sdc_no]; |
| struct mmc_config *cfg = &priv->cfg; |
| int ret; |
| |
| memset(priv, '\0', sizeof(struct sunxi_mmc_priv)); |
| |
| cfg->name = "SUNXI SD/MMC"; |
| cfg->ops = &sunxi_mmc_ops; |
| |
| cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34; |
| cfg->host_caps = MMC_MODE_4BIT; |
| #if defined(CONFIG_MACH_SUN50I) || defined(CONFIG_MACH_SUN8I) || defined(CONFIG_SUN50I_GEN_H6) |
| if (sdc_no == 2) |
| cfg->host_caps = MMC_MODE_8BIT; |
| #endif |
| cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS; |
| cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT; |
| |
| cfg->f_min = 400000; |
| cfg->f_max = 52000000; |
| |
| if (mmc_resource_init(sdc_no) != 0) |
| return NULL; |
| |
| /* config ahb clock */ |
| debug("init mmc %d clock and io\n", sdc_no); |
| #if !defined(CONFIG_SUN50I_GEN_H6) |
| setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_MMC(sdc_no)); |
| |
| #ifdef CONFIG_SUNXI_GEN_SUN6I |
| /* unassert reset */ |
| setbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_RESET_OFFSET_MMC(sdc_no)); |
| #endif |
| #if defined(CONFIG_MACH_SUN9I) |
| /* sun9i has a mmc-common module, also set the gate and reset there */ |
| writel(SUNXI_MMC_COMMON_CLK_GATE | SUNXI_MMC_COMMON_RESET, |
| SUNXI_MMC_COMMON_BASE + 4 * sdc_no); |
| #endif |
| #else /* CONFIG_SUN50I_GEN_H6 */ |
| setbits_le32(&ccm->sd_gate_reset, 1 << sdc_no); |
| /* unassert reset */ |
| setbits_le32(&ccm->sd_gate_reset, 1 << (RESET_SHIFT + sdc_no)); |
| #endif |
| ret = mmc_set_mod_clk(priv, 24000000); |
| if (ret) |
| return NULL; |
| |
| return mmc_create(cfg, priv); |
| } |
| #else |
| |
| static int sunxi_mmc_set_ios(struct udevice *dev) |
| { |
| struct sunxi_mmc_plat *plat = dev_get_plat(dev); |
| struct sunxi_mmc_priv *priv = dev_get_priv(dev); |
| |
| return sunxi_mmc_set_ios_common(priv, &plat->mmc); |
| } |
| |
| static int sunxi_mmc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd, |
| struct mmc_data *data) |
| { |
| struct sunxi_mmc_plat *plat = dev_get_plat(dev); |
| struct sunxi_mmc_priv *priv = dev_get_priv(dev); |
| |
| return sunxi_mmc_send_cmd_common(priv, &plat->mmc, cmd, data); |
| } |
| |
| static int sunxi_mmc_getcd(struct udevice *dev) |
| { |
| struct sunxi_mmc_priv *priv = dev_get_priv(dev); |
| |
| if (dm_gpio_is_valid(&priv->cd_gpio)) { |
| int cd_state = dm_gpio_get_value(&priv->cd_gpio); |
| |
| return cd_state ^ priv->cd_inverted; |
| } |
| return 1; |
| } |
| |
| static const struct dm_mmc_ops sunxi_mmc_ops = { |
| .send_cmd = sunxi_mmc_send_cmd, |
| .set_ios = sunxi_mmc_set_ios, |
| .get_cd = sunxi_mmc_getcd, |
| }; |
| |
| static unsigned get_mclk_offset(void) |
| { |
| if (IS_ENABLED(CONFIG_MACH_SUN9I_A80)) |
| return 0x410; |
| |
| if (IS_ENABLED(CONFIG_SUN50I_GEN_H6)) |
| return 0x830; |
| |
| return 0x88; |
| }; |
| |
| static int sunxi_mmc_probe(struct udevice *dev) |
| { |
| struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); |
| struct sunxi_mmc_plat *plat = dev_get_plat(dev); |
| struct sunxi_mmc_priv *priv = dev_get_priv(dev); |
| struct reset_ctl_bulk reset_bulk; |
| struct clk gate_clk; |
| struct mmc_config *cfg = &plat->cfg; |
| struct ofnode_phandle_args args; |
| u32 *ccu_reg; |
| int bus_width, ret; |
| |
| cfg->name = dev->name; |
| bus_width = dev_read_u32_default(dev, "bus-width", 1); |
| |
| cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34; |
| cfg->host_caps = 0; |
| if (bus_width == 8) |
| cfg->host_caps |= MMC_MODE_8BIT; |
| if (bus_width >= 4) |
| cfg->host_caps |= MMC_MODE_4BIT; |
| cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS; |
| cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT; |
| |
| cfg->f_min = 400000; |
| cfg->f_max = 52000000; |
| |
| priv->reg = (void *)dev_read_addr(dev); |
| |
| /* We don't have a sunxi clock driver so find the clock address here */ |
| ret = dev_read_phandle_with_args(dev, "clocks", "#clock-cells", 0, |
| 1, &args); |
| if (ret) |
| return ret; |
| ccu_reg = (u32 *)ofnode_get_addr(args.node); |
| |
| priv->mmc_no = ((uintptr_t)priv->reg - SUNXI_MMC0_BASE) / 0x1000; |
| priv->mclkreg = (void *)ccu_reg + get_mclk_offset() + priv->mmc_no * 4; |
| |
| ret = clk_get_by_name(dev, "ahb", &gate_clk); |
| if (!ret) |
| clk_enable(&gate_clk); |
| |
| ret = reset_get_bulk(dev, &reset_bulk); |
| if (!ret) |
| reset_deassert_bulk(&reset_bulk); |
| |
| ret = mmc_set_mod_clk(priv, 24000000); |
| if (ret) |
| return ret; |
| |
| /* This GPIO is optional */ |
| if (!dev_read_bool(dev, "non-removable") && |
| !gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio, |
| GPIOD_IS_IN)) { |
| int cd_pin = gpio_get_number(&priv->cd_gpio); |
| |
| sunxi_gpio_set_pull(cd_pin, SUNXI_GPIO_PULL_UP); |
| } |
| |
| /* Check if card detect is inverted */ |
| priv->cd_inverted = dev_read_bool(dev, "cd-inverted"); |
| |
| upriv->mmc = &plat->mmc; |
| |
| /* Reset controller */ |
| writel(SUNXI_MMC_GCTRL_RESET, &priv->reg->gctrl); |
| udelay(1000); |
| |
| return 0; |
| } |
| |
| static int sunxi_mmc_bind(struct udevice *dev) |
| { |
| struct sunxi_mmc_plat *plat = dev_get_plat(dev); |
| |
| return mmc_bind(dev, &plat->mmc, &plat->cfg); |
| } |
| |
| static const struct udevice_id sunxi_mmc_ids[] = { |
| { .compatible = "allwinner,sun4i-a10-mmc" }, |
| { .compatible = "allwinner,sun5i-a13-mmc" }, |
| { .compatible = "allwinner,sun7i-a20-mmc" }, |
| { .compatible = "allwinner,sun8i-a83t-emmc" }, |
| { .compatible = "allwinner,sun9i-a80-mmc" }, |
| { .compatible = "allwinner,sun50i-a64-mmc" }, |
| { .compatible = "allwinner,sun50i-a64-emmc" }, |
| { .compatible = "allwinner,sun50i-h6-mmc" }, |
| { .compatible = "allwinner,sun50i-h6-emmc" }, |
| { .compatible = "allwinner,sun50i-a100-mmc" }, |
| { .compatible = "allwinner,sun50i-a100-emmc" }, |
| { /* sentinel */ } |
| }; |
| |
| U_BOOT_DRIVER(sunxi_mmc_drv) = { |
| .name = "sunxi_mmc", |
| .id = UCLASS_MMC, |
| .of_match = sunxi_mmc_ids, |
| .bind = sunxi_mmc_bind, |
| .probe = sunxi_mmc_probe, |
| .ops = &sunxi_mmc_ops, |
| .plat_auto = sizeof(struct sunxi_mmc_plat), |
| .priv_auto = sizeof(struct sunxi_mmc_priv), |
| }; |
| #endif |