blob: 93d3b790b2bac564768ef0ad3c6dbce22a990937 [file] [log] [blame]
/**
* @file IxEthMii.h
*
* @brief this file contains the public API of @ref IxEthMii component
*
* Design notes :
* The main intent of this API is to inplement MII high level fonctionalitoes
* to support the codelets provided with the IXP400 software releases. It
* superceedes previous interfaces provided with @ref IxEThAcc component.
*
* This API has been tested with the PHYs provided with the
* IXP400 development platforms. It may not work for specific Ethernet PHYs
* used on specific boards.
*
* This source code detects and interface the LXT972, LXT973 and KS6995
* Ethernet PHYs.
*
* This source code should be considered as an example which may need
* to be adapted for different hardware implementations.
*
* It is strongly recommended to use public domain and GPL utilities
* like libmii, mii-diag for MII interface support.
*
*
*
* @par
* IXP400 SW Release version 2.0
*
* -- Copyright Notice --
*
* @par
* Copyright 2001-2005, Intel Corporation.
* All rights reserved.
*
* @par
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of the Intel Corporation nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* @par
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS''
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* @par
* -- End of Copyright Notice --
*/
#ifndef IxEthMii_H
#define IxEthMii_H
#include <IxTypes.h>
/**
* @defgroup IxEthMii IXP400 Ethernet Phy Access (IxEthMii) API
*
* @brief ethMii is a library that does provides access to the
* Ethernet PHYs
*
*@{
*/
/**
* @ingroup IxEthMii
*
* @fn ixEthMiiPhyScan(BOOL phyPresent[], UINT32 maxPhyCount)
*
* @brief Scan the MDIO bus for PHYs
* This function scans PHY addresses 0 through 31, and sets phyPresent[n] to
* true if a phy is discovered at address n.
*
* - Reentrant - no
* - ISR Callable - no
*
* @pre The MAC on Ethernet Port 2 (NPE C) must be initialised, and generating the MDIO clock.
*
* @param phyPresent BOOL [in] - boolean array of IXP425_ETH_ACC_MII_MAX_ADDR entries
* @param maxPhyCount UINT32 [in] - number of PHYs to search for (the scan will stop when
* the indicated number of PHYs is found).
*
* @return IX_STATUS
* - IX_ETH_ACC_SUCCESS
* - IX_ETH_ACC_FAIL : invalid arguments.
*
* <hr>
*/
PUBLIC IX_STATUS ixEthMiiPhyScan(BOOL phyPresent[], UINT32 maxPhyCount);
/**
* @ingroup IxEthMii
*
* @fn ixEthMiiPhyConfig(UINT32 phyAddr,
BOOL speed100,
BOOL fullDuplex,
BOOL autonegotiate)
*
*
* @brief Configure a PHY
* Configure a PHY's speed, duplex and autonegotiation status
*
* - Reentrant - no
* - ISR Callable - no
*
* @pre The MAC on Ethernet Port 2 (NPE C) must be initialised, and generating the MDIO clock.
*
* @param phyAddr UINT32 [in]
* @param speed100 BOOL [in] - set to true for 100Mbit/s operation, false for 10Mbit/s
* @param fullDuplex BOOL [in] - set to true for Full Duplex, false for Half Duplex
* @param autonegotiate BOOL [in] - set to true to enable autonegotiation
*
* @return IX_STATUS
* - IX_SUCCESS
* - IX_FAIL : invalid arguments.
*
* <hr>
*/
PUBLIC IX_STATUS ixEthMiiPhyConfig(UINT32 phyAddr,
BOOL speed100,
BOOL fullDuplex,
BOOL autonegotiate);
/**
* @ingroup IxEthMii
*
* @fn ixEthMiiPhyLoopbackEnable(UINT32 phyAddr)
*
*
* @brief Enable PHY Loopback in a specific Eth MII port
*
* @note When PHY Loopback is enabled, frames sent out to the PHY from the
* IXP400 will be looped back to the IXP400. They will not be transmitted out
* on the wire.
*
* - Reentrant - no
* - ISR Callable - no
*
* @param phyAddr UINT32 [in] - the address of the Ethernet PHY (0-31)
*
* @return IX_STATUS
* - IX_SUCCESS
* - IX_FAIL : invalid arguments.
* <hr>
*/
PUBLIC IX_STATUS
ixEthMiiPhyLoopbackEnable (UINT32 phyAddr);
/**
* @ingroup IxEthMii
*
* @fn ixEthMiiPhyLoopbackDisable(UINT32 phyAddr)
*
*
* @brief Disable PHY Loopback in a specific Eth MII port
*
* - Reentrant - no
* - ISR Callable - no
*
* @param phyAddr UINT32 [in] - the address of the Ethernet PHY (0-31)
*
* @return IX_STATUS
* - IX_SUCCESS
* - IX_FAIL : invalid arguments.
* <hr>
*/
PUBLIC IX_STATUS
ixEthMiiPhyLoopbackDisable (UINT32 phyAddr);
/**
* @ingroup IxEthMii
*
* @fn ixEthMiiPhyReset(UINT32 phyAddr)
*
* @brief Reset a PHY
* Reset a PHY
*
* - Reentrant - no
* - ISR Callable - no
*
* @pre The MAC on Ethernet Port 2 (NPE C) must be initialised, and generating the MDIO clock.
*
* @param phyAddr UINT32 [in] - the address of the Ethernet PHY (0-31)
*
* @return IX_STATUS
* - IX_SUCCESS
* - IX_FAIL : invalid arguments.
*
* <hr>
*/
PUBLIC IX_STATUS ixEthMiiPhyReset(UINT32 phyAddr);
/**
* @ingroup IxEthMii
*
* @fn ixEthMiiLinkStatus(UINT32 phyAddr,
BOOL *linkUp,
BOOL *speed100,
BOOL *fullDuplex,
BOOL *autoneg)
*
* @brief Retrieve the current status of a PHY
* Retrieve the link, speed, duplex and autonegotiation status of a PHY
*
* - Reentrant - no
* - ISR Callable - no
*
* @pre The MAC on Ethernet Port 2 (NPE C) must be initialised, and generating the MDIO clock.
*
* @param phyAddr UINT32 [in] - the address of the Ethernet PHY (0-31)
* @param linkUp BOOL [out] - set to true if the link is up
* @param speed100 BOOL [out] - set to true indicates 100Mbit/s, false indicates 10Mbit/s
* @param fullDuplex BOOL [out] - set to true indicates Full Duplex, false indicates Half Duplex
* @param autoneg BOOL [out] - set to true indicates autonegotiation is enabled, false indicates autonegotiation is disabled
*
* @return IX_STATUS
* - IX_SUCCESS
* - IX_FAIL : invalid arguments.
*
* <hr>
*/
PUBLIC IX_STATUS ixEthMiiLinkStatus(UINT32 phyAddr,
BOOL *linkUp,
BOOL *speed100,
BOOL *fullDuplex,
BOOL *autoneg);
/**
* @ingroup IxEthMii
*
* @fn ixEthMiiPhyShow (UINT32 phyAddr)
*
*
* @brief Display information on a specified PHY
* Display link status, speed, duplex and Auto Negotiation status
*
* - Reentrant - no
* - ISR Callable - no
*
* @pre The MAC on Ethernet Port 2 (NPE C) must be initialised, and generating the MDIO clock.
*
* @param phyAddr UINT32 [in] - the address of the Ethernet PHY (0-31)
*
* @return IX_STATUS
* - IX_SUCCESS
* - IX_FAIL : invalid arguments.
*
* <hr>
*/
PUBLIC IX_STATUS ixEthMiiPhyShow (UINT32 phyAddr);
#endif /* ndef IxEthMii_H */
/**
*@}
*/