| /* |
| * U-boot - Configuration file for BlackStamp board |
| * Configuration by Ben Matthews for UR LLE using bf533-stamp.h |
| * as a template |
| * See http://blackfin.uclinux.org/gf/project/blackstamp/ |
| */ |
| |
| #ifndef __CONFIG_BLACKSTAMP_H__ |
| #define __CONFIG_BLACKSTAMP_H__ |
| |
| #include <asm/config-pre.h> |
| |
| /* |
| * Debugging: Set these options if you're having problems |
| */ |
| /* |
| * #define CONFIG_DEBUG_EARLY_SERIAL |
| * #define DEBUG |
| * #define CONFIG_DEBUG_DUMP |
| * #define CONFIG_DEBUG_DUMP_SYMS |
| */ |
| #define CONFIG_PANIC_HANG 0 |
| |
| /* CPU Options |
| * Be sure to set the Silicon Revision Correctly |
| */ |
| #define CONFIG_BFIN_CPU bf532-0.5 |
| #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER |
| |
| /* |
| * Board settings |
| */ |
| #define CONFIG_SMC91111 1 |
| #define CONFIG_SMC91111_BASE 0x20300300 |
| |
| /* FLASH/ETHERNET uses the same address range |
| * Depending on what you have the CPLD doing |
| * this probably isn't needed |
| */ |
| #define SHARED_RESOURCES 1 |
| |
| /* Is I2C bit-banged? */ |
| #undef CONFIG_SOFT_I2 |
| |
| /* |
| * Clock Settings |
| * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV |
| * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV |
| */ |
| /* CONFIG_CLKIN_HZ is any value in Hz */ |
| #define CONFIG_CLKIN_HZ 25000000 |
| /* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ |
| /* 1 = CLKIN / 2 */ |
| #define CONFIG_CLKIN_HALF 0 |
| /* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ |
| /* 1 = bypass PLL */ |
| #define CONFIG_PLL_BYPASS 0 |
| /* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ |
| /* Values can range from 0-63 (where 0 means 64) */ |
| #define CONFIG_VCO_MULT 16 |
| /* CCLK_DIV controls the core clock divider */ |
| /* Values can be 1, 2, 4, or 8 ONLY */ |
| #define CONFIG_CCLK_DIV 1 |
| /* SCLK_DIV controls the system clock divider */ |
| /* Values can range from 1-15 */ |
| #define CONFIG_SCLK_DIV 3 |
| |
| /* |
| * Network settings |
| */ |
| |
| #ifdef CONFIG_SMC91111 |
| #define CONFIG_IPADDR 192.168.0.15 |
| #define CONFIG_NETMASK 255.255.255.0 |
| #define CONFIG_GATEWAYIP 192.168.0.1 |
| #define CONFIG_SERVERIP 192.168.0.2 |
| #define CONFIG_HOSTNAME blackstamp |
| #define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs |
| #define CONFIG_SYS_AUTOLOAD "no" |
| |
| /* To remove hardcoding and enable MAC storage in EEPROM */ |
| /* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ |
| #endif |
| |
| #define CONFIG_ENV_IS_IN_SPI_FLASH |
| #define CONFIG_ENV_OFFSET 0x40000 |
| #define CONFIG_ENV_SIZE 0x2000 |
| #define CONFIG_ENV_SECT_SIZE 0x40000 |
| |
| /* |
| * SDRAM settings & memory map |
| */ |
| |
| #define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */ |
| #define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */ |
| |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) |
| #define CONFIG_SYS_MALLOC_LEN (384 << 10) |
| |
| /* |
| * Command settings |
| */ |
| |
| #define CONFIG_SYS_LONGHELP 1 |
| #define CONFIG_CMDLINE_EDITING 1 |
| #define CONFIG_AUTO_COMPLETE 1 |
| #define CONFIG_ENV_OVERWRITE 1 |
| |
| #include <config_cmd_default.h> |
| |
| #ifdef CONFIG_SMC91111 |
| # define CONFIG_CMD_DHCP |
| # define CONFIG_CMD_PING |
| #else |
| # undef CONFIG_CMD_NET |
| #endif |
| |
| #ifdef CONFIG_SOFT_I2C |
| # define CONFIG_CMD_I2C |
| #endif |
| |
| #define CONFIG_CMD_BOOTLDR |
| #define CONFIG_CMD_CACHE |
| #define CONFIG_CMD_CPLBINFO |
| #define CONFIG_CMD_DATE |
| #define CONFIG_CMD_SF |
| #define CONFIG_CMD_ELF |
| |
| #define CONFIG_BOOTDELAY 5 |
| #define CONFIG_BOOTCOMMAND "run ramboot" |
| #define CONFIG_BOOTARGS \ |
| "root=/dev/mtdblock0 rw " \ |
| "clkin_hz=" MK_STR(CONFIG_CLKIN_HZ) " " \ |
| "earlyprintk=" \ |
| "serial," \ |
| "uart" MK_STR(CONFIG_UART_CONSOLE) "," \ |
| MK_STR(CONFIG_BAUDRATE) " " \ |
| "console=ttyBF0," MK_STR(CONFIG_BAUDRATE) |
| |
| #if defined(CONFIG_CMD_NET) |
| # if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) |
| # define UBOOT_ENV_FILE "u-boot.bin" |
| # else |
| # define UBOOT_ENV_FILE "u-boot.ldr" |
| # endif |
| # if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) |
| # ifdef CONFIG_SPI |
| # define UBOOT_ENV_UPDATE \ |
| "eeprom write $(loadaddr) 0x0 $(filesize)" |
| # else |
| # define UBOOT_ENV_UPDATE \ |
| "sf probe " MK_STR(BFIN_BOOT_SPI_SSEL) ";" \ |
| "sf erase 0 0x40000;" \ |
| "sf write $(loadaddr) 0 $(filesize)" |
| # endif |
| # else |
| # define UBOOT_ENV_UPDATE \ |
| "protect off 0x20000000 0x2003FFFF;" \ |
| "erase 0x20000000 0x2003FFFF;" \ |
| "cp.b $(loadaddr) 0x20000000 $(filesize)" |
| # endif |
| # define NETWORK_ENV_SETTINGS \ |
| "ubootfile=" UBOOT_ENV_FILE "\0" \ |
| "update=" \ |
| "tftp $(loadaddr) $(ubootfile);" \ |
| UBOOT_ENV_UPDATE \ |
| "\0" \ |
| "addip=set bootargs $(bootargs) " \ |
| "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):" \ |
| "$(hostname):eth0:off" \ |
| "\0" \ |
| "ramargs=set bootargs " CONFIG_BOOTARGS "\0" \ |
| "ramboot=" \ |
| "tftp $(loadaddr) uImage;" \ |
| "run ramargs;" \ |
| "run addip;" \ |
| "bootm" \ |
| "\0" \ |
| "nfsargs=set bootargs " \ |
| "root=/dev/nfs rw " \ |
| "nfsroot=$(serverip):$(rootpath),tcp,nfsvers=3" \ |
| "\0" \ |
| "nfsboot=" \ |
| "tftp $(loadaddr) vmImage;" \ |
| "run nfsargs;" \ |
| "run addip;" \ |
| "bootm" \ |
| "\0" |
| #else |
| # define NETWORK_ENV_SETTINGS |
| #endif |
| |
| /* |
| * Console settings |
| */ |
| #define CONFIG_BAUDRATE 57600 |
| #define CONFIG_LOADS_ECHO 1 |
| #define CONFIG_UART_CONSOLE 0 |
| |
| /* |
| * I2C settings |
| * By default PF2 is used as SDA and PF3 as SCL on the Stamp board |
| * Located on the expansion connector on pins 86/85 |
| * Note these pins are arbitrarily chosen because we aren't using |
| * them yet. You can (and probably should) change these values! |
| */ |
| #ifdef CONFIG_SOFT_I2C |
| #define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF9 |
| #define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF8 |
| #define CONFIG_SYS_I2C_SPEED 50000 |
| #define CONFIG_SYS_I2C_SLAVE 0xFE |
| #endif |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_RTC_BFIN 1 |
| |
| /* |
| * Serial Flash Infomation |
| */ |
| #define CONFIG_BFIN_SPI |
| /* For the M25P64 SCK Should be Kept < 15Mhz */ |
| #define CONFIG_ENV_SPI_MAX_HZ 15000000 |
| #define CONFIG_SF_DEFAULT_SPEED 15000000 |
| #define CONFIG_SPI_FLASH |
| #define CONFIG_SPI_FLASH_STMICRO |
| |
| /* |
| * FLASH organization and environment definitions |
| */ |
| |
| #define CONFIG_EBIU_AMGCTL_VAL 0xFF |
| #define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3 |
| #define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983 |
| #define CONFIG_EBIU_SDRRC_VAL 0x268 |
| #define CONFIG_EBIU_SDGCTL_VAL 0x911109 |
| |
| /* Even though Rev C boards have Parallel Flash |
| * We aren't supporting it. Newer versions of the |
| * hardware don't support Parallel Flash at all. |
| */ |
| #define CONFIG_SYS_NO_FLASH |
| #undef CONFIG_CMD_IMLS |
| #undef CONFIG_CMD_JFFS2 |
| #undef CONFIG_CMD_FLASH |
| |
| #endif |