powerpc/T104xD4RDB: Add T104xD4RDB boards support
T1040D4RDB is a Freescale reference board that hosts the T1040 SoC.
T1040D4RDB is re-designed T1040RDB board with following changes :
- Support of DDR4 memory
- Support of 0x66 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 1 SGMII on DTSEC3
- Support of QE-TDM
Similarily T1042D4RDB is a Freescale reference board that hosts the T1040
SoC. T1042D4RDB is re-designed T1042RDB board with following changes :
- Support of DDR4 memory
- Support for 0x86 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 3 SGMII on DTSEC1, DTSEC2 & DTSEC3
- Support of DIU
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README
index ac95b5e..b9d2212 100644
--- a/board/freescale/t104xrdb/README
+++ b/board/freescale/t104xrdb/README
@@ -12,6 +12,17 @@
(a personality of T1040 SoC). The board is similar to T1040RDB but is
designed specially with low power features targeted for Printing Image Market.
+The T1040D4RDB is a Freescale reference board that hosts the T1040 SoC.
+The board is re-designed T1040RDB board with following changes :
+ - Support of DDR4 memory and some enhancements
+
+The T1042D4RDB is a Freescale reference board that hosts the T1042 SoC.
+The board is re-designed T1040RDB board with following changes :
+ - Support of DDR4 memory
+ - Support for 0x86 serdes protocol which can support following interfaces
+ - 2 RGMII's on DTSEC4, DTSEC5
+ - 3 SGMII on DTSEC1, DTSEC2 & DTSEC3
+
Basic difference's among T1040RDB, T1042RDB_PI, T1042RDB
-------------------------------------------------------------------------
Board Si Protocol Targeted Market
@@ -19,6 +30,8 @@
T1040RDB T1040 0x66 Networking
T1040RDB T1042 0x86 Networking
T1042RDB_PI T1042 0x06 Printing & Imaging
+T1040D4RDB T1040 0x66 Networking
+T1042D4RDB T1042 0x86 Networking
T1040 SoC Overview
@@ -70,7 +83,6 @@
T1040 SoC Personalities
-------------------------
-
T1022 Personality:
T1022 is a reduced personality of T1040 with less core/clusters.
@@ -268,8 +280,13 @@
Please note QE Firmware is only valid for T1040RDB
-Switch Settings: (ON is 0, OFF is 1)
-===============
+Switch Settings for T104xRDB boards: (ON is 0, OFF is 1)
+==========================================================
+NOR boot SW setting:
+SW1: 00010011
+SW2: 10111011
+SW3: 11100001
+
NAND boot SW setting:
SW1: 10001000
SW2: 00111011
@@ -284,3 +301,67 @@
SW1: 00100000
SW2: 00111011
SW3: 11100001
+
+Switch Settings for T104xD4RDB boards: (ON is 0, OFF is 1)
+=============================================================
+NOR boot SW setting:
+SW1: 00010011
+SW2: 10111001
+SW3: 11100001
+
+NAND boot SW setting:
+SW1: 10001000
+SW2: 00111001
+SW3: 11110001
+
+SPI boot SW setting:
+SW1: 00100010
+SW2: 10111001
+SW3: 11100001
+
+SD boot SW setting:
+SW1: 00100000
+SW2: 00111001
+SW3: 11100001
+
+PBL-based image generation
+==========================
+Changes only the required register bit in in PBI commands.
+
+Provides reference code which might needs some
+modification as per requirement.
+example:
+By default PBI_SRC=14 (which is for IFC-NAND/NOR) in rcw.cfg file
+which needs to be changed for SPI and SD.
+
+For SD-boot
+==============
+1. Set RCW[192:195], PBI_SRC bits as 6 in RCW file (t1040d4_rcw.cfg type files)
+
+example:
+ RCW file: board/freescale/t104xrdb/t1040d4_rcw.cfg
+
+Change
+66000002 40000002 ec027000 01000000
+to
+66000002 40000002 6c027000 01000000
+
+2. SD does not support flush so remove flush from pbl, make changes in
+ tools/pblimage.c file, Update value of pbl_end_cmd[0] = 0x09138000
+ with 0x091380c0
+
+For SPI-boot
+==============
+1. Set RCW[192:195], PBI_SRC bits as 5 in RCW file (t1040d4_rcw.cfg type files)
+
+example:
+ RCW file: board/freescale/t104xrdb/t1040d4_rcw.cfg
+
+Change
+66000002 40000002 ec027000 01000000
+to
+66000002 40000002 5c027000 01000000
+
+2. SPI does not support flush so remove flush from pbl, make changes in
+ tools/pblimage.c file, Update value of pbl_end_cmd[0] = 0x09138000
+ with 0x091380c0