| // SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause |
| /* |
| * Copyright (C) 2018, STMicroelectronics - All Rights Reserved |
| */ |
| |
| #include <config.h> |
| #include <common.h> |
| #include <asm/armv7.h> |
| #include <asm/cache.h> |
| #include <asm/gic.h> |
| #include <asm/io.h> |
| #include <asm/psci.h> |
| #include <asm/secure.h> |
| #include <hang.h> |
| #include <linux/bitops.h> |
| |
| /* PWR */ |
| #define PWR_CR3 0x0c |
| #define PWR_MPUCR 0x10 |
| |
| #define PWR_CR3_DDRSREN BIT(10) |
| #define PWR_CR3_DDRRETEN BIT(12) |
| |
| #define PWR_MPUCR_PDDS BIT(0) |
| #define PWR_MPUCR_CSTDBYDIS BIT(3) |
| #define PWR_MPUCR_CSSF BIT(9) |
| |
| /* RCC */ |
| #define RCC_DDRITFCR 0xd8 |
| |
| #define RCC_DDRITFCR_DDRC1EN BIT(0) |
| #define RCC_DDRITFCR_DDRC1LPEN BIT(1) |
| #define RCC_DDRITFCR_DDRC2EN BIT(2) |
| #define RCC_DDRITFCR_DDRC2LPEN BIT(3) |
| #define RCC_DDRITFCR_DDRPHYCEN BIT(4) |
| #define RCC_DDRITFCR_DDRPHYCLPEN BIT(5) |
| #define RCC_DDRITFCR_DDRCAPBEN BIT(6) |
| #define RCC_DDRITFCR_DDRCAPBLPEN BIT(7) |
| #define RCC_DDRITFCR_AXIDCGEN BIT(8) |
| #define RCC_DDRITFCR_DDRPHYCAPBEN BIT(9) |
| #define RCC_DDRITFCR_DDRPHYCAPBLPEN BIT(10) |
| #define RCC_DDRITFCR_DDRCKMOD_MASK GENMASK(22, 20) |
| #define RCC_DDRITFCR_GSKPCTRL BIT(24) |
| |
| #define RCC_MP_SREQSETR 0x104 |
| #define RCC_MP_SREQCLRR 0x108 |
| |
| #define RCC_MP_CIER 0x414 |
| #define RCC_MP_CIFR 0x418 |
| #define RCC_MP_CIFR_WKUPF BIT(20) |
| |
| /* SYSCFG */ |
| #define SYSCFG_CMPCR 0x20 |
| #define SYSCFG_CMPCR_SW_CTRL BIT(2) |
| #define SYSCFG_CMPENSETR 0x24 |
| #define SYSCFG_CMPENCLRR 0x28 |
| #define SYSCFG_CMPENR_MPUEN BIT(0) |
| |
| /* DDR Controller registers offsets */ |
| #define DDRCTRL_STAT 0x004 |
| #define DDRCTRL_PWRCTL 0x030 |
| #define DDRCTRL_PWRTMG 0x034 |
| #define DDRCTRL_HWLPCTL 0x038 |
| #define DDRCTRL_DFIMISC 0x1b0 |
| #define DDRCTRL_SWCTL 0x320 |
| #define DDRCTRL_SWSTAT 0x324 |
| #define DDRCTRL_PSTAT 0x3fc |
| #define DDRCTRL_PCTRL_0 0x490 |
| #define DDRCTRL_PCTRL_1 0x540 |
| |
| /* DDR Controller Register fields */ |
| #define DDRCTRL_STAT_OPERATING_MODE_MASK GENMASK(2, 0) |
| #define DDRCTRL_STAT_OPERATING_MODE_NORMAL 0x1 |
| #define DDRCTRL_STAT_OPERATING_MODE_SR 0x3 |
| #define DDRCTRL_STAT_SELFREF_TYPE_MASK GENMASK(5, 4) |
| #define DDRCTRL_STAT_SELFREF_TYPE_ASR (0x3 << 4) |
| #define DDRCTRL_STAT_SELFREF_TYPE_SR (0x2 << 4) |
| |
| #define DDRCTRL_PWRCTL_SELFREF_EN BIT(0) |
| #define DDRCTRL_PWRCTL_EN_DFI_DRAM_CLK_DISABLE BIT(3) |
| #define DDRCTRL_PWRCTL_SELFREF_SW BIT(5) |
| |
| #define DDRCTRL_PWRTMG_SELFREF_TO_X32_MASK GENMASK(23, 16) |
| #define DDRCTRL_PWRTMG_SELFREF_TO_X32_0 BIT(16) |
| |
| #define DDRCTRL_HWLPCTL_HW_LP_EN BIT(0) |
| |
| #define DDRCTRL_DFIMISC_DFI_INIT_COMPLETE_EN BIT(0) |
| |
| #define DDRCTRL_SWCTL_SW_DONE BIT(0) |
| |
| #define DDRCTRL_SWSTAT_SW_DONE_ACK BIT(0) |
| |
| #define DDRCTRL_PSTAT_RD_PORT_BUSY_0 BIT(0) |
| #define DDRCTRL_PSTAT_RD_PORT_BUSY_1 BIT(1) |
| #define DDRCTRL_PSTAT_WR_PORT_BUSY_0 BIT(16) |
| #define DDRCTRL_PSTAT_WR_PORT_BUSY_1 BIT(17) |
| |
| #define DDRCTRL_PCTRL_N_PORT_EN BIT(0) |
| |
| /* DDR PHY registers offsets */ |
| #define DDRPHYC_PIR 0x004 |
| #define DDRPHYC_PGSR 0x00c |
| #define DDRPHYC_ACDLLCR 0x014 |
| #define DDRPHYC_ACIOCR 0x024 |
| #define DDRPHYC_DXCCR 0x028 |
| #define DDRPHYC_DSGCR 0x02c |
| #define DDRPHYC_ZQ0CR0 0x180 |
| #define DDRPHYC_DX0DLLCR 0x1cc |
| #define DDRPHYC_DX1DLLCR 0x20c |
| #define DDRPHYC_DX2DLLCR 0x24c |
| #define DDRPHYC_DX3DLLCR 0x28c |
| |
| /* DDR PHY Register fields */ |
| #define DDRPHYC_PIR_INIT BIT(0) |
| #define DDRPHYC_PIR_DLLSRST BIT(1) |
| #define DDRPHYC_PIR_DLLLOCK BIT(2) |
| #define DDRPHYC_PIR_ITMSRST BIT(4) |
| |
| #define DDRPHYC_PGSR_IDONE BIT(0) |
| |
| #define DDRPHYC_ACDLLCR_DLLSRST BIT(30) |
| #define DDRPHYC_ACDLLCR_DLLDIS BIT(31) |
| |
| #define DDRPHYC_ACIOCR_ACOE BIT(1) |
| #define DDRPHYC_ACIOCR_ACPDD BIT(3) |
| #define DDRPHYC_ACIOCR_ACPDR BIT(4) |
| #define DDRPHYC_ACIOCR_CKPDD_MASK GENMASK(10, 8) |
| #define DDRPHYC_ACIOCR_CKPDD_0 BIT(8) |
| #define DDRPHYC_ACIOCR_CKPDR_MASK GENMASK(13, 11) |
| #define DDRPHYC_ACIOCR_CKPDR_0 BIT(11) |
| #define DDRPHYC_ACIOCR_CSPDD_MASK GENMASK(20, 18) |
| #define DDRPHYC_ACIOCR_CSPDD_0 BIT(18) |
| |
| #define DDRPHYC_DXCCR_DXPDD BIT(2) |
| #define DDRPHYC_DXCCR_DXPDR BIT(3) |
| |
| #define DDRPHYC_DSGCR_CKEPDD_MASK GENMASK(19, 16) |
| #define DDRPHYC_DSGCR_CKEPDD_0 BIT(16) |
| #define DDRPHYC_DSGCR_ODTPDD_MASK GENMASK(23, 20) |
| #define DDRPHYC_DSGCR_ODTPDD_0 BIT(20) |
| #define DDRPHYC_DSGCR_NL2PD BIT(24) |
| #define DDRPHYC_DSGCR_CKOE BIT(28) |
| |
| #define DDRPHYC_ZQ0CRN_ZQPD BIT(31) |
| |
| #define DDRPHYC_DXNDLLCR_DLLDIS BIT(31) |
| |
| #define BOOT_API_A7_CORE0_MAGIC_NUMBER 0xca7face0 |
| #define BOOT_API_A7_CORE1_MAGIC_NUMBER 0xca7face1 |
| |
| #define MPIDR_AFF0 GENMASK(7, 0) |
| |
| #define RCC_MP_GRSTCSETR (STM32_RCC_BASE + 0x0404) |
| #define RCC_MP_GRSTCSETR_MPSYSRST BIT(0) |
| #define RCC_MP_GRSTCSETR_MPUP0RST BIT(4) |
| #define RCC_MP_GRSTCSETR_MPUP1RST BIT(5) |
| |
| #define STM32MP1_PSCI_NR_CPUS 2 |
| #if STM32MP1_PSCI_NR_CPUS > CONFIG_ARMV7_PSCI_NR_CPUS |
| #error "invalid value for CONFIG_ARMV7_PSCI_NR_CPUS" |
| #endif |
| |
| u8 psci_state[STM32MP1_PSCI_NR_CPUS] __secure_data = { |
| PSCI_AFFINITY_LEVEL_ON, |
| PSCI_AFFINITY_LEVEL_OFF}; |
| |
| static u32 __secure_data cntfrq; |
| |
| static u32 __secure cp15_read_cntfrq(void) |
| { |
| u32 frq; |
| |
| asm volatile("mrc p15, 0, %0, c14, c0, 0" : "=r" (frq)); |
| |
| return frq; |
| } |
| |
| static void __secure cp15_write_cntfrq(u32 frq) |
| { |
| asm volatile ("mcr p15, 0, %0, c14, c0, 0" : : "r" (frq)); |
| } |
| |
| static inline void psci_set_state(int cpu, u8 state) |
| { |
| psci_state[cpu] = state; |
| dsb(); |
| isb(); |
| } |
| |
| static u32 __secure stm32mp_get_gicd_base_address(void) |
| { |
| u32 periphbase; |
| |
| /* get the GIC base address from the CBAR register */ |
| asm("mrc p15, 4, %0, c15, c0, 0\n" : "=r" (periphbase)); |
| |
| return (periphbase & CBAR_MASK) + GIC_DIST_OFFSET; |
| } |
| |
| static void __secure stm32mp_raise_sgi0(int cpu) |
| { |
| u32 gic_dist_addr; |
| |
| gic_dist_addr = stm32mp_get_gicd_base_address(); |
| |
| /* ask cpu with SGI0 */ |
| writel((BIT(cpu) << 16), gic_dist_addr + GICD_SGIR); |
| } |
| |
| void __secure psci_arch_cpu_entry(void) |
| { |
| u32 cpu = psci_get_cpu_id(); |
| |
| psci_set_state(cpu, PSCI_AFFINITY_LEVEL_ON); |
| |
| /* write the saved cntfrq */ |
| cp15_write_cntfrq(cntfrq); |
| |
| /* reset magic in TAMP register */ |
| writel(0xFFFFFFFF, TAMP_BACKUP_MAGIC_NUMBER); |
| } |
| |
| s32 __secure psci_features(u32 function_id, u32 psci_fid) |
| { |
| switch (psci_fid) { |
| case ARM_PSCI_0_2_FN_PSCI_VERSION: |
| case ARM_PSCI_0_2_FN_CPU_OFF: |
| case ARM_PSCI_0_2_FN_CPU_ON: |
| case ARM_PSCI_0_2_FN_AFFINITY_INFO: |
| case ARM_PSCI_0_2_FN_MIGRATE_INFO_TYPE: |
| case ARM_PSCI_0_2_FN_SYSTEM_OFF: |
| case ARM_PSCI_0_2_FN_SYSTEM_RESET: |
| case ARM_PSCI_1_0_FN_SYSTEM_SUSPEND: |
| return 0x0; |
| } |
| return ARM_PSCI_RET_NI; |
| } |
| |
| u32 __secure psci_version(void) |
| { |
| return ARM_PSCI_VER_1_0; |
| } |
| |
| s32 __secure psci_affinity_info(u32 function_id, u32 target_affinity, |
| u32 lowest_affinity_level) |
| { |
| u32 cpu = target_affinity & MPIDR_AFF0; |
| |
| if (lowest_affinity_level > 0) |
| return ARM_PSCI_RET_INVAL; |
| |
| if (target_affinity & ~MPIDR_AFF0) |
| return ARM_PSCI_RET_INVAL; |
| |
| if (cpu >= STM32MP1_PSCI_NR_CPUS) |
| return ARM_PSCI_RET_INVAL; |
| |
| return psci_state[cpu]; |
| } |
| |
| u32 __secure psci_migrate_info_type(void) |
| { |
| /* |
| * in Power_State_Coordination_Interface_PDD_v1_1_DEN0022D.pdf |
| * return 2 = Trusted OS is either not present or does not require |
| * migration, system of this type does not require the caller |
| * to use the MIGRATE function. |
| * MIGRATE function calls return NOT_SUPPORTED. |
| */ |
| return 2; |
| } |
| |
| s32 __secure psci_cpu_on(u32 function_id, u32 target_cpu, u32 pc, |
| u32 context_id) |
| { |
| u32 cpu = target_cpu & MPIDR_AFF0; |
| |
| if (target_cpu & ~MPIDR_AFF0) |
| return ARM_PSCI_RET_INVAL; |
| |
| if (cpu >= STM32MP1_PSCI_NR_CPUS) |
| return ARM_PSCI_RET_INVAL; |
| |
| if (psci_state[cpu] == PSCI_AFFINITY_LEVEL_ON) |
| return ARM_PSCI_RET_ALREADY_ON; |
| |
| /* read and save cntfrq of current cpu to write on target cpu */ |
| cntfrq = cp15_read_cntfrq(); |
| |
| /* reset magic in TAMP register */ |
| if (readl(TAMP_BACKUP_MAGIC_NUMBER)) |
| writel(0xFFFFFFFF, TAMP_BACKUP_MAGIC_NUMBER); |
| /* |
| * ROM code need a first SGI0 after core reset |
| * core is ready when magic is set to 0 in ROM code |
| */ |
| while (readl(TAMP_BACKUP_MAGIC_NUMBER)) |
| stm32mp_raise_sgi0(cpu); |
| |
| /* store target PC and context id*/ |
| psci_save(cpu, pc, context_id); |
| |
| /* write entrypoint in backup RAM register */ |
| writel((u32)&psci_cpu_entry, TAMP_BACKUP_BRANCH_ADDRESS); |
| psci_set_state(cpu, PSCI_AFFINITY_LEVEL_ON_PENDING); |
| |
| /* write magic number in backup register */ |
| if (cpu == 0x01) |
| writel(BOOT_API_A7_CORE1_MAGIC_NUMBER, |
| TAMP_BACKUP_MAGIC_NUMBER); |
| else |
| writel(BOOT_API_A7_CORE0_MAGIC_NUMBER, |
| TAMP_BACKUP_MAGIC_NUMBER); |
| |
| /* Generate an IT to start the core */ |
| stm32mp_raise_sgi0(cpu); |
| |
| return ARM_PSCI_RET_SUCCESS; |
| } |
| |
| s32 __secure psci_cpu_off(void) |
| { |
| u32 cpu; |
| |
| cpu = psci_get_cpu_id(); |
| |
| psci_cpu_off_common(); |
| psci_set_state(cpu, PSCI_AFFINITY_LEVEL_OFF); |
| |
| /* reset core: wfi is managed by BootRom */ |
| if (cpu == 0x01) |
| writel(RCC_MP_GRSTCSETR_MPUP1RST, RCC_MP_GRSTCSETR); |
| else |
| writel(RCC_MP_GRSTCSETR_MPUP0RST, RCC_MP_GRSTCSETR); |
| |
| /* just waiting reset */ |
| while (1) |
| wfi(); |
| } |
| |
| void __secure psci_system_reset(void) |
| { |
| /* System reset */ |
| writel(RCC_MP_GRSTCSETR_MPSYSRST, RCC_MP_GRSTCSETR); |
| /* just waiting reset */ |
| while (1) |
| wfi(); |
| } |
| |
| void __secure psci_system_off(void) |
| { |
| /* System Off is not managed, waiting user power off |
| * TODO: handle I2C write in PMIC Main Control register bit 0 = SWOFF |
| */ |
| while (1) |
| wfi(); |
| } |
| |
| static void __secure secure_udelay(unsigned int delay) |
| { |
| u32 freq = cp15_read_cntfrq() / 1000000; |
| u64 start, end; |
| |
| delay *= freq; |
| |
| asm volatile("mrrc p15, 0, %Q0, %R0, c14" : "=r" (start)); |
| for (;;) { |
| asm volatile("mrrc p15, 0, %Q0, %R0, c14" : "=r" (end)); |
| if ((end - start) > delay) |
| break; |
| } |
| } |
| |
| static int __secure secure_waitbits(u32 reg, u32 mask, u32 val) |
| { |
| u32 freq = cp15_read_cntfrq() / 1000000; |
| u32 delay = 500 * freq; /* 500 us */ |
| u64 start, end; |
| u32 tmp; |
| |
| asm volatile("mrrc p15, 0, %Q0, %R0, c14" : "=r" (start)); |
| for (;;) { |
| tmp = readl(reg); |
| tmp &= mask; |
| if ((tmp & val) == val) |
| return 0; |
| asm volatile("mrrc p15, 0, %Q0, %R0, c14" : "=r" (end)); |
| if ((end - start) > delay) |
| return -ETIMEDOUT; |
| } |
| } |
| |
| static void __secure ddr_sr_mode_ssr(u32 *saved_pwrctl) |
| { |
| setbits_le32(STM32_RCC_BASE + RCC_DDRITFCR, |
| RCC_DDRITFCR_DDRC1LPEN | RCC_DDRITFCR_DDRC1EN | |
| RCC_DDRITFCR_DDRC2LPEN | RCC_DDRITFCR_DDRC2EN | |
| RCC_DDRITFCR_DDRCAPBLPEN | RCC_DDRITFCR_DDRPHYCAPBLPEN | |
| RCC_DDRITFCR_DDRCAPBEN | RCC_DDRITFCR_DDRPHYCAPBEN | |
| RCC_DDRITFCR_DDRPHYCEN); |
| |
| clrbits_le32(STM32_RCC_BASE + RCC_DDRITFCR, |
| RCC_DDRITFCR_AXIDCGEN | RCC_DDRITFCR_DDRCKMOD_MASK); |
| |
| /* Disable HW LP interface of uMCTL2 */ |
| clrbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_HWLPCTL, |
| DDRCTRL_HWLPCTL_HW_LP_EN); |
| |
| /* Configure Automatic LP modes of uMCTL2 */ |
| clrsetbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PWRTMG, |
| DDRCTRL_PWRTMG_SELFREF_TO_X32_MASK, |
| DDRCTRL_PWRTMG_SELFREF_TO_X32_0); |
| |
| /* Save PWRCTL register to restart ASR after suspend (if applicable) */ |
| *saved_pwrctl = readl(STM32_DDRCTRL_BASE + DDRCTRL_PWRCTL); |
| |
| /* |
| * Disable Clock disable with LP modes |
| * (used in RUN mode for LPDDR2 with specific timing). |
| */ |
| clrbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PWRCTL, |
| DDRCTRL_PWRCTL_EN_DFI_DRAM_CLK_DISABLE); |
| |
| /* Disable automatic Self-Refresh mode */ |
| clrbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PWRCTL, |
| DDRCTRL_PWRCTL_SELFREF_EN); |
| } |
| |
| static void __secure ddr_sr_mode_restore(u32 saved_pwrctl) |
| { |
| saved_pwrctl &= DDRCTRL_PWRCTL_EN_DFI_DRAM_CLK_DISABLE | |
| DDRCTRL_PWRCTL_SELFREF_EN; |
| |
| /* Restore ASR mode in case it was enabled before suspend. */ |
| setbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PWRCTL, saved_pwrctl); |
| } |
| |
| static int __secure ddr_sw_self_refresh_in(void) |
| { |
| int ret; |
| |
| clrbits_le32(STM32_RCC_BASE + RCC_DDRITFCR, RCC_DDRITFCR_AXIDCGEN); |
| |
| /* Blocks AXI ports from taking anymore transactions */ |
| clrbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PCTRL_0, |
| DDRCTRL_PCTRL_N_PORT_EN); |
| clrbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PCTRL_1, |
| DDRCTRL_PCTRL_N_PORT_EN); |
| |
| /* |
| * Waits unit all AXI ports are idle |
| * Poll PSTAT.rd_port_busy_n = 0 |
| * Poll PSTAT.wr_port_busy_n = 0 |
| */ |
| ret = secure_waitbits(STM32_DDRCTRL_BASE + DDRCTRL_PSTAT, |
| DDRCTRL_PSTAT_RD_PORT_BUSY_0 | |
| DDRCTRL_PSTAT_RD_PORT_BUSY_1 | |
| DDRCTRL_PSTAT_WR_PORT_BUSY_0 | |
| DDRCTRL_PSTAT_WR_PORT_BUSY_1, 0); |
| if (ret) |
| goto pstat_failed; |
| |
| /* SW Self-Refresh entry */ |
| setbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PWRCTL, DDRCTRL_PWRCTL_SELFREF_SW); |
| |
| /* |
| * Wait operating mode change in self-refresh mode |
| * with STAT.operating_mode[1:0]==11. |
| * Ensure transition to self-refresh was due to software |
| * by checking also that STAT.selfref_type[1:0]=2. |
| */ |
| ret = secure_waitbits(STM32_DDRCTRL_BASE + DDRCTRL_STAT, |
| DDRCTRL_STAT_OPERATING_MODE_MASK | |
| DDRCTRL_STAT_SELFREF_TYPE_MASK, |
| DDRCTRL_STAT_OPERATING_MODE_SR | |
| DDRCTRL_STAT_SELFREF_TYPE_SR); |
| if (ret) |
| goto selfref_sw_failed; |
| |
| /* IOs powering down (PUBL registers) */ |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACIOCR, DDRPHYC_ACIOCR_ACPDD); |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACIOCR, DDRPHYC_ACIOCR_ACPDR); |
| |
| clrsetbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACIOCR, |
| DDRPHYC_ACIOCR_CKPDD_MASK, |
| DDRPHYC_ACIOCR_CKPDD_0); |
| |
| clrsetbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACIOCR, |
| DDRPHYC_ACIOCR_CKPDR_MASK, |
| DDRPHYC_ACIOCR_CKPDR_0); |
| |
| clrsetbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACIOCR, |
| DDRPHYC_ACIOCR_CSPDD_MASK, |
| DDRPHYC_ACIOCR_CSPDD_0); |
| |
| /* Disable command/address output driver */ |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACIOCR, DDRPHYC_ACIOCR_ACOE); |
| |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DXCCR, DDRPHYC_DXCCR_DXPDD); |
| |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DXCCR, DDRPHYC_DXCCR_DXPDR); |
| |
| clrsetbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DSGCR, |
| DDRPHYC_DSGCR_ODTPDD_MASK, |
| DDRPHYC_DSGCR_ODTPDD_0); |
| |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DSGCR, DDRPHYC_DSGCR_NL2PD); |
| |
| clrsetbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DSGCR, |
| DDRPHYC_DSGCR_CKEPDD_MASK, |
| DDRPHYC_DSGCR_CKEPDD_0); |
| |
| /* Disable PZQ cell (PUBL register) */ |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ZQ0CR0, DDRPHYC_ZQ0CRN_ZQPD); |
| |
| /* Set latch */ |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DSGCR, DDRPHYC_DSGCR_CKOE); |
| |
| /* Additional delay to avoid early latch */ |
| secure_udelay(10); |
| |
| /* Activate sw retention in PWRCTRL */ |
| setbits_le32(STM32_PWR_BASE + PWR_CR3, PWR_CR3_DDRRETEN); |
| |
| /* Switch controller clocks (uMCTL2/PUBL) to DLL ref clock */ |
| setbits_le32(STM32_RCC_BASE + RCC_DDRITFCR, RCC_DDRITFCR_GSKPCTRL); |
| |
| /* Disable all DLLs: GLITCH window */ |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACDLLCR, DDRPHYC_ACDLLCR_DLLDIS); |
| |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DX0DLLCR, DDRPHYC_DXNDLLCR_DLLDIS); |
| |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DX1DLLCR, DDRPHYC_DXNDLLCR_DLLDIS); |
| |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DX2DLLCR, DDRPHYC_DXNDLLCR_DLLDIS); |
| |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DX3DLLCR, DDRPHYC_DXNDLLCR_DLLDIS); |
| |
| /* Switch controller clocks (uMCTL2/PUBL) to DLL output clock */ |
| clrbits_le32(STM32_RCC_BASE + RCC_DDRITFCR, RCC_DDRITFCR_GSKPCTRL); |
| |
| /* Deactivate all DDR clocks */ |
| clrbits_le32(STM32_RCC_BASE + RCC_DDRITFCR, |
| RCC_DDRITFCR_DDRC1EN | RCC_DDRITFCR_DDRC2EN | |
| RCC_DDRITFCR_DDRCAPBEN | RCC_DDRITFCR_DDRPHYCAPBEN); |
| |
| return 0; |
| |
| selfref_sw_failed: |
| /* This bit should be cleared to restore DDR in its previous state */ |
| clrbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PWRCTL, |
| DDRCTRL_PWRCTL_SELFREF_SW); |
| |
| pstat_failed: |
| setbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PCTRL_0, |
| DDRCTRL_PCTRL_N_PORT_EN); |
| setbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PCTRL_1, |
| DDRCTRL_PCTRL_N_PORT_EN); |
| |
| return -EINVAL; |
| }; |
| |
| static void __secure ddr_sw_self_refresh_exit(void) |
| { |
| int ret; |
| |
| /* Enable all clocks */ |
| setbits_le32(STM32_RCC_BASE + RCC_DDRITFCR, |
| RCC_DDRITFCR_DDRC1EN | RCC_DDRITFCR_DDRC2EN | |
| RCC_DDRITFCR_DDRPHYCEN | RCC_DDRITFCR_DDRPHYCAPBEN | |
| RCC_DDRITFCR_DDRCAPBEN); |
| |
| /* Handshake */ |
| clrbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_SWCTL, DDRCTRL_SWCTL_SW_DONE); |
| |
| /* Mask dfi_init_complete_en */ |
| clrbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_DFIMISC, |
| DDRCTRL_DFIMISC_DFI_INIT_COMPLETE_EN); |
| |
| /* Ack */ |
| setbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_SWCTL, DDRCTRL_SWCTL_SW_DONE); |
| ret = secure_waitbits(STM32_DDRCTRL_BASE + DDRCTRL_SWSTAT, |
| DDRCTRL_SWSTAT_SW_DONE_ACK, |
| DDRCTRL_SWSTAT_SW_DONE_ACK); |
| if (ret) |
| hang(); |
| |
| /* Switch controller clocks (uMCTL2/PUBL) to DLL ref clock */ |
| setbits_le32(STM32_RCC_BASE + RCC_DDRITFCR, RCC_DDRITFCR_GSKPCTRL); |
| |
| /* Enable all DLLs: GLITCH window */ |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACDLLCR, |
| DDRPHYC_ACDLLCR_DLLDIS); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DX0DLLCR, DDRPHYC_DXNDLLCR_DLLDIS); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DX1DLLCR, DDRPHYC_DXNDLLCR_DLLDIS); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DX2DLLCR, DDRPHYC_DXNDLLCR_DLLDIS); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DX3DLLCR, DDRPHYC_DXNDLLCR_DLLDIS); |
| |
| /* Additional delay to avoid early DLL clock switch */ |
| secure_udelay(50); |
| |
| /* Switch controller clocks (uMCTL2/PUBL) to DLL ref clock */ |
| clrbits_le32(STM32_RCC_BASE + RCC_DDRITFCR, RCC_DDRITFCR_GSKPCTRL); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACDLLCR, DDRPHYC_ACDLLCR_DLLSRST); |
| |
| secure_udelay(10); |
| |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACDLLCR, DDRPHYC_ACDLLCR_DLLSRST); |
| |
| /* PHY partial init: (DLL lock and ITM reset) */ |
| writel(DDRPHYC_PIR_DLLSRST | DDRPHYC_PIR_DLLLOCK | |
| DDRPHYC_PIR_ITMSRST | DDRPHYC_PIR_INIT, |
| STM32_DDRPHYC_BASE + DDRPHYC_PIR); |
| |
| /* Need to wait at least 10 clock cycles before accessing PGSR */ |
| secure_udelay(1); |
| |
| /* Pool end of init */ |
| ret = secure_waitbits(STM32_DDRPHYC_BASE + DDRPHYC_PGSR, |
| DDRPHYC_PGSR_IDONE, DDRPHYC_PGSR_IDONE); |
| if (ret) |
| hang(); |
| |
| /* Handshake */ |
| clrbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_SWCTL, DDRCTRL_SWCTL_SW_DONE); |
| |
| /* Unmask dfi_init_complete_en to uMCTL2 */ |
| setbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_DFIMISC, DDRCTRL_DFIMISC_DFI_INIT_COMPLETE_EN); |
| |
| /* Ack */ |
| setbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_SWCTL, DDRCTRL_SWCTL_SW_DONE); |
| ret = secure_waitbits(STM32_DDRCTRL_BASE + DDRCTRL_SWSTAT, |
| DDRCTRL_SWSTAT_SW_DONE_ACK, |
| DDRCTRL_SWSTAT_SW_DONE_ACK); |
| if (ret) |
| hang(); |
| |
| /* Deactivate sw retention in PWR */ |
| clrbits_le32(STM32_PWR_BASE + PWR_CR3, PWR_CR3_DDRRETEN); |
| |
| /* Enable PZQ cell (PUBL register) */ |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ZQ0CR0, DDRPHYC_ZQ0CRN_ZQPD); |
| |
| /* Enable pad drivers */ |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACIOCR, DDRPHYC_ACIOCR_ACPDD); |
| |
| /* Enable command/address output driver */ |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACIOCR, DDRPHYC_ACIOCR_ACOE); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACIOCR, DDRPHYC_ACIOCR_CKPDD_MASK); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_ACIOCR, DDRPHYC_ACIOCR_CSPDD_MASK); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DXCCR, DDRPHYC_DXCCR_DXPDD); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DXCCR, DDRPHYC_DXCCR_DXPDR); |
| |
| /* Release latch */ |
| setbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DSGCR, DDRPHYC_DSGCR_CKOE); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DSGCR, DDRPHYC_DSGCR_ODTPDD_MASK); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DSGCR, DDRPHYC_DSGCR_NL2PD); |
| |
| clrbits_le32(STM32_DDRPHYC_BASE + DDRPHYC_DSGCR, DDRPHYC_DSGCR_CKEPDD_MASK); |
| |
| /* Remove selfrefresh */ |
| clrbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PWRCTL, DDRCTRL_PWRCTL_SELFREF_SW); |
| |
| /* Wait operating_mode == normal */ |
| ret = secure_waitbits(STM32_DDRCTRL_BASE + DDRCTRL_STAT, |
| DDRCTRL_STAT_OPERATING_MODE_MASK, |
| DDRCTRL_STAT_OPERATING_MODE_NORMAL); |
| if (ret) |
| hang(); |
| |
| /* AXI ports are no longer blocked from taking transactions */ |
| setbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PCTRL_0, DDRCTRL_PCTRL_N_PORT_EN); |
| setbits_le32(STM32_DDRCTRL_BASE + DDRCTRL_PCTRL_1, DDRCTRL_PCTRL_N_PORT_EN); |
| |
| setbits_le32(STM32_RCC_BASE + RCC_DDRITFCR, RCC_DDRITFCR_AXIDCGEN); |
| } |
| |
| void __secure psci_system_suspend(u32 __always_unused function_id, |
| u32 ep, u32 context_id) |
| { |
| u32 saved_pwrctl, reg; |
| |
| /* Disable IO compensation */ |
| |
| /* Place current APSRC/ANSRC into RAPSRC/RANSRC */ |
| reg = readl(STM32_SYSCFG_BASE + SYSCFG_CMPCR); |
| reg >>= 8; |
| reg &= 0xff << 16; |
| reg |= SYSCFG_CMPCR_SW_CTRL; |
| writel(reg, STM32_SYSCFG_BASE + SYSCFG_CMPCR); |
| writel(SYSCFG_CMPENR_MPUEN, STM32_SYSCFG_BASE + SYSCFG_CMPENCLRR); |
| |
| writel(RCC_MP_CIFR_WKUPF, STM32_RCC_BASE + RCC_MP_CIFR); |
| setbits_le32(STM32_RCC_BASE + RCC_MP_CIER, RCC_MP_CIFR_WKUPF); |
| |
| setbits_le32(STM32_PWR_BASE + PWR_MPUCR, |
| PWR_MPUCR_CSSF | PWR_MPUCR_CSTDBYDIS | PWR_MPUCR_PDDS); |
| |
| psci_v7_flush_dcache_all(); |
| ddr_sr_mode_ssr(&saved_pwrctl); |
| ddr_sw_self_refresh_in(); |
| setbits_le32(STM32_PWR_BASE + PWR_CR3, PWR_CR3_DDRSREN); |
| writel(0x3, STM32_RCC_BASE + RCC_MP_SREQSETR); |
| |
| /* Zzz, enter stop mode */ |
| asm volatile( |
| "isb\n" |
| "dsb\n" |
| "wfi\n"); |
| |
| writel(0x3, STM32_RCC_BASE + RCC_MP_SREQCLRR); |
| ddr_sw_self_refresh_exit(); |
| ddr_sr_mode_restore(saved_pwrctl); |
| |
| writel(SYSCFG_CMPENR_MPUEN, STM32_SYSCFG_BASE + SYSCFG_CMPENSETR); |
| clrbits_le32(STM32_SYSCFG_BASE + SYSCFG_CMPCR, SYSCFG_CMPCR_SW_CTRL); |
| } |