| /* |
| * GE b1x5v2 - QMX6 SPL |
| * |
| * Copyright 2013, Adeneo Embedded <www.adeneo-embedded.com> |
| * Copyright 2018-2020 GE Inc. |
| * Copyright 2018-2020 Collabora Ltd. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <asm/arch/clock.h> |
| #include <asm/arch/crm_regs.h> |
| #include <asm/arch/imx-regs.h> |
| #include <asm/arch/iomux.h> |
| #include <asm/arch/mx6-pins.h> |
| #include <asm/arch/sys_proto.h> |
| #include <asm/gpio.h> |
| #include <init.h> |
| #include <spi.h> |
| #include <spi_flash.h> |
| #include <spl.h> |
| |
| #if defined(CONFIG_SPL_BUILD) |
| |
| #include <asm/arch/mx6-ddr.h> |
| |
| #define IMX6DQ_DRIVE_STRENGTH_40_OHM 0x30 |
| #define IMX6DQ_DRIVE_STRENGTH_48_OHM 0x28 |
| #define IMX6DQ_DRIVE_STRENGTH IMX6DQ_DRIVE_STRENGTH_40_OHM |
| |
| #define QMX6_DDR_PKE_DISABLED 0x00000000 |
| #define QMX6_DDR_ODT_60_OHM (2 << 16) |
| #define QMX6_DDR_TYPE_DDR3 0x000c0000 |
| |
| #define QMX6_DRAM_SDCKE_PULLUP_100K 0x00003000 |
| #define QMX6_DRAM_SDBA2_PULLUP_NONE 0x00000000 |
| |
| #define SPI_PAD_CTRL (PAD_CTL_HYS | \ |
| PAD_CTL_SPEED_MED | \ |
| PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) |
| |
| #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ |
| PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ |
| PAD_CTL_SRE_FAST | PAD_CTL_HYS) |
| |
| #define SPI1_CS0 IMX_GPIO_NR(3, 19) |
| #define POWEROFF IMX_GPIO_NR(4, 25) |
| |
| static iomux_v3_cfg_t const poweroff_pads[] = { |
| IOMUX_PADS(PAD_DISP0_DAT4__GPIO4_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| }; |
| |
| static iomux_v3_cfg_t const uart2_pads[] = { |
| IOMUX_PADS(PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
| IOMUX_PADS(PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
| }; |
| |
| static iomux_v3_cfg_t const uart3_pads[] = { |
| IOMUX_PADS(PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
| IOMUX_PADS(PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)), |
| }; |
| |
| static iomux_v3_cfg_t const ecspi1_pads[] = { |
| IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)), |
| IOMUX_PADS(PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)), |
| IOMUX_PADS(PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL)), |
| IOMUX_PADS(PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL)), |
| }; |
| |
| static struct mx6dq_iomux_ddr_regs mx6q_ddr_ioregs = { |
| .dram_sdclk_0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdclk_1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_cas = IMX6DQ_DRIVE_STRENGTH, |
| .dram_ras = IMX6DQ_DRIVE_STRENGTH, |
| .dram_reset = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdcke0 = QMX6_DRAM_SDCKE_PULLUP_100K, |
| .dram_sdcke1 = QMX6_DRAM_SDCKE_PULLUP_100K, |
| .dram_sdba2 = QMX6_DRAM_SDBA2_PULLUP_NONE, |
| .dram_sdodt0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdodt1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs2 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs3 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs4 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs5 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs6 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs7 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm2 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm3 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm4 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm5 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm6 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm7 = IMX6DQ_DRIVE_STRENGTH, |
| }; |
| |
| static const struct mx6sdl_iomux_ddr_regs mx6dl_ddr_ioregs = { |
| .dram_sdclk_0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdclk_1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_cas = IMX6DQ_DRIVE_STRENGTH, |
| .dram_ras = IMX6DQ_DRIVE_STRENGTH, |
| .dram_reset = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdcke0 = QMX6_DRAM_SDCKE_PULLUP_100K, |
| .dram_sdcke1 = QMX6_DRAM_SDCKE_PULLUP_100K, |
| .dram_sdba2 = QMX6_DRAM_SDBA2_PULLUP_NONE, |
| .dram_sdodt0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdodt1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs2 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs3 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs4 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs5 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs6 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_sdqs7 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm0 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm1 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm2 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm3 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm4 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm5 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm6 = IMX6DQ_DRIVE_STRENGTH, |
| .dram_dqm7 = IMX6DQ_DRIVE_STRENGTH, |
| }; |
| |
| static struct mx6dq_iomux_grp_regs mx6q_grp_ioregs = { |
| .grp_ddr_type = QMX6_DDR_TYPE_DDR3, |
| .grp_ddrmode_ctl = QMX6_DDR_ODT_60_OHM, |
| .grp_ddrpke = QMX6_DDR_PKE_DISABLED, |
| .grp_addds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_ctlds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_ddrmode = QMX6_DDR_ODT_60_OHM, |
| .grp_b0ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b1ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b2ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b3ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b4ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b5ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b6ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b7ds = IMX6DQ_DRIVE_STRENGTH, |
| }; |
| |
| static const struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = { |
| .grp_ddr_type = QMX6_DDR_TYPE_DDR3, |
| .grp_ddrmode_ctl = QMX6_DDR_ODT_60_OHM, |
| .grp_ddrpke = QMX6_DDR_PKE_DISABLED, |
| .grp_addds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_ctlds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_ddrmode = QMX6_DDR_ODT_60_OHM, |
| .grp_b0ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b1ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b2ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b3ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b4ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b5ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b6ds = IMX6DQ_DRIVE_STRENGTH, |
| .grp_b7ds = IMX6DQ_DRIVE_STRENGTH, |
| }; |
| |
| const struct mx6_mmdc_calibration mx6q_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x0016001A, |
| .p0_mpwldectrl1 = 0x0023001C, |
| .p1_mpwldectrl0 = 0x0028003A, |
| .p1_mpwldectrl1 = 0x001F002C, |
| .p0_mpdgctrl0 = 0x43440354, |
| .p0_mpdgctrl1 = 0x033C033C, |
| .p1_mpdgctrl0 = 0x43300368, |
| .p1_mpdgctrl1 = 0x03500330, |
| .p0_mprddlctl = 0x3228242E, |
| .p1_mprddlctl = 0x2C2C2636, |
| .p0_mpwrdlctl = 0x36323A38, |
| .p1_mpwrdlctl = 0x42324440, |
| }; |
| |
| const struct mx6_mmdc_calibration mx6q_2g_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x00080016, |
| .p0_mpwldectrl1 = 0x001D0016, |
| .p1_mpwldectrl0 = 0x0018002C, |
| .p1_mpwldectrl1 = 0x000D001D, |
| .p0_mpdgctrl0 = 0x43200334, |
| .p0_mpdgctrl1 = 0x0320031C, |
| .p1_mpdgctrl0 = 0x0344034C, |
| .p1_mpdgctrl1 = 0x03380314, |
| .p0_mprddlctl = 0x3E36383A, |
| .p1_mprddlctl = 0x38363240, |
| .p0_mpwrdlctl = 0x36364238, |
| .p1_mpwrdlctl = 0x4230423E, |
| }; |
| |
| const struct mx6_mmdc_calibration mx6q_4g_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x00180018, |
| .p0_mpwldectrl1 = 0x00220018, |
| .p1_mpwldectrl0 = 0x00330046, |
| .p1_mpwldectrl1 = 0x002B003D, |
| .p0_mpdgctrl0 = 0x4344034C, |
| .p0_mpdgctrl1 = 0x033C033C, |
| .p1_mpdgctrl0 = 0x03700374, |
| .p1_mpdgctrl1 = 0x03600338, |
| .p0_mprddlctl = 0x443E3E40, |
| .p1_mprddlctl = 0x423E3E48, |
| .p0_mpwrdlctl = 0x3C3C4442, |
| .p1_mpwrdlctl = 0x46384C46, |
| }; |
| |
| static const struct mx6_mmdc_calibration mx6s_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x00480049, |
| .p0_mpwldectrl1 = 0x00410044, |
| .p0_mpdgctrl0 = 0x42480248, |
| .p0_mpdgctrl1 = 0x023C023C, |
| .p0_mprddlctl = 0x40424644, |
| .p0_mpwrdlctl = 0x34323034, |
| }; |
| |
| static const struct mx6_mmdc_calibration mx6s_2g_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x00450048, |
| .p0_mpwldectrl1 = 0x003B003F, |
| .p0_mpdgctrl0 = 0x424C0248, |
| .p0_mpdgctrl1 = 0x0234023C, |
| .p0_mprddlctl = 0x40444848, |
| .p0_mpwrdlctl = 0x38363232, |
| }; |
| |
| static const struct mx6_mmdc_calibration mx6dl_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x0043004B, |
| .p0_mpwldectrl1 = 0x003A003E, |
| .p1_mpwldectrl0 = 0x0047004F, |
| .p1_mpwldectrl1 = 0x004E0061, |
| .p0_mpdgctrl0 = 0x42500250, |
| .p0_mpdgctrl1 = 0x0238023C, |
| .p1_mpdgctrl0 = 0x42640264, |
| .p1_mpdgctrl1 = 0x02500258, |
| .p0_mprddlctl = 0x40424846, |
| .p1_mprddlctl = 0x46484842, |
| .p0_mpwrdlctl = 0x38382C30, |
| .p1_mpwrdlctl = 0x34343430, |
| }; |
| |
| static const struct mx6_mmdc_calibration mx6dl_2g_mmcd_calib = { |
| .p0_mpwldectrl0 = 0x00450045, |
| .p0_mpwldectrl1 = 0x00390043, |
| .p1_mpwldectrl0 = 0x0049004D, |
| .p1_mpwldectrl1 = 0x004E0061, |
| .p0_mpdgctrl0 = 0x4240023C, |
| .p0_mpdgctrl1 = 0x0228022C, |
| .p1_mpdgctrl0 = 0x02400244, |
| .p1_mpdgctrl1 = 0x02340238, |
| .p0_mprddlctl = 0x42464648, |
| .p1_mprddlctl = 0x4446463C, |
| .p0_mpwrdlctl = 0x3C38323A, |
| .p1_mpwrdlctl = 0x34323430, |
| }; |
| |
| static struct mx6_ddr3_cfg mem_ddr_2g = { |
| .mem_speed = 1600, |
| .density = 2, |
| .width = 16, |
| .banks = 8, |
| .rowaddr = 14, |
| .coladdr = 10, |
| .pagesz = 2, |
| .trcd = 1310, |
| .trcmin = 4875, |
| .trasmin = 3500, |
| }; |
| |
| static struct mx6_ddr3_cfg mem_ddr_4g = { |
| .mem_speed = 1600, |
| .density = 4, |
| .width = 16, |
| .banks = 8, |
| .rowaddr = 15, |
| .coladdr = 10, |
| .pagesz = 2, |
| .trcd = 1310, |
| .trcmin = 4875, |
| .trasmin = 3500, |
| }; |
| |
| static struct mx6_ddr3_cfg mem_ddr_8g = { |
| .mem_speed = 1600, |
| .density = 8, |
| .width = 16, |
| .banks = 8, |
| .rowaddr = 16, |
| .coladdr = 10, |
| .pagesz = 2, |
| .trcd = 1310, |
| .trcmin = 4875, |
| .trasmin = 3500, |
| }; |
| |
| static void spl_dram_init(u8 width, u32 memsize) { |
| struct mx6_ddr_sysinfo sysinfo = { |
| /* width of data bus: 0=16, 1=32, 2=64 */ |
| .dsize = width / 32, |
| /* config for full 4GB range so that get_mem_size() works */ |
| .cs_density = 32, /* 32Gb per CS */ |
| |
| .ncs = 1, |
| .cs1_mirror = 0, |
| .rtt_wr = 2, |
| .rtt_nom = 2, |
| .walat = 0, |
| .ralat = 5, |
| .mif3_mode = 3, |
| .bi_on = 1, |
| .sde_to_rst = 0x0d, |
| .rst_to_cke = 0x20, |
| }; |
| |
| if (is_cpu_type(MXC_CPU_MX6SOLO)) { |
| sysinfo.walat = 1; |
| mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs); |
| |
| switch(memsize) { |
| case 512: |
| mx6_dram_cfg(&sysinfo, &mx6s_2g_mmcd_calib, &mem_ddr_2g); |
| break; |
| default: |
| mx6_dram_cfg(&sysinfo, &mx6s_mmcd_calib, &mem_ddr_4g); |
| break; |
| } |
| } else if (is_cpu_type(MXC_CPU_MX6DL)) { |
| sysinfo.walat = 1; |
| mx6sdl_dram_iocfg(width, &mx6dl_ddr_ioregs, &mx6sdl_grp_ioregs); |
| |
| switch(memsize) { |
| case 2048: |
| mx6_dram_cfg(&sysinfo, &mx6dl_2g_mmcd_calib, &mem_ddr_4g); |
| break; |
| default: |
| mx6_dram_cfg(&sysinfo, &mx6dl_mmcd_calib, &mem_ddr_2g); |
| break; |
| } |
| } else if (is_cpu_type(MXC_CPU_MX6Q)) { |
| mx6dq_dram_iocfg(width, &mx6q_ddr_ioregs, &mx6q_grp_ioregs); |
| |
| switch(memsize) { |
| case 4096: |
| sysinfo.cs_density = 16; |
| sysinfo.ncs = 2; |
| mx6_dram_cfg(&sysinfo, &mx6q_4g_mmcd_calib, &mem_ddr_8g); |
| break; |
| case 2048: |
| mx6_dram_cfg(&sysinfo, &mx6q_2g_mmcd_calib, &mem_ddr_4g); |
| break; |
| default: |
| mx6_dram_cfg(&sysinfo, &mx6q_mmcd_calib, &mem_ddr_2g); |
| break; |
| } |
| } |
| } |
| |
| /* Define a minimal structure so that the part number can be read via SPL */ |
| #define CFG_MFG_ADDR_OFFSET (spi->size - SZ_16K) |
| struct mfgdata { |
| unsigned char tsize; |
| /* size of checksummed part in bytes */ |
| unsigned char ckcnt; |
| /* checksum corrected byte */ |
| unsigned char cksum; |
| /* decimal serial number, packed BCD */ |
| unsigned char serial[6]; |
| /* part number, right justified, ASCII */ |
| unsigned char pn[16]; |
| }; |
| |
| static void conv_ascii(unsigned char *dst, unsigned char *src, int len) |
| { |
| int remain = len; |
| unsigned char *sptr = src; |
| unsigned char *dptr = dst; |
| |
| while (remain) { |
| if (*sptr) { |
| *dptr = *sptr; |
| dptr++; |
| } |
| sptr++; |
| remain--; |
| } |
| *dptr = 0x0; |
| } |
| |
| /* |
| * Returns the total size of the memory [in MB] the board is equipped with |
| * |
| * This is determined via the partnumber which is stored in the |
| * congatec manufacturing area |
| */ |
| static int get_boardmem_size(struct spi_flash *spi) |
| { |
| int ret; |
| int i; |
| int arraysize; |
| char buf[sizeof(struct mfgdata)]; |
| struct mfgdata *data = (struct mfgdata *)buf; |
| unsigned char outbuf[32]; |
| char partnumbers_2g[4][7] = { "016104", "016105", "016304", "016305" }; |
| char partnumbers_4g[2][7] = { "016308", "016318" }; |
| char partnumbers_512m[2][7] = { "016203", "616300" }; |
| |
| ret = spi_flash_read(spi, CFG_MFG_ADDR_OFFSET, sizeof(struct mfgdata), |
| buf); |
| if (ret) |
| return 1024; /* default to 1GByte in case of error */ |
| |
| conv_ascii(outbuf, data->pn, sizeof(data->pn)); |
| |
| printf("Detected Congatec QMX6 SOM: %s\n", outbuf); |
| |
| /* congatec PN 016104, 016105, 016304, 016305 have 2GiB of RAM */ |
| arraysize = sizeof(partnumbers_2g) / sizeof(partnumbers_2g[0]); |
| for (i=0; i < arraysize; i++) { |
| if (!memcmp(outbuf,partnumbers_2g[i],6)) |
| return 2048; |
| } |
| |
| /* congatec PN 016308, 016318 have 4GiB of RAM */ |
| arraysize = sizeof(partnumbers_4g) / sizeof(partnumbers_4g[0]); |
| for (i=0; i < arraysize; i++) { |
| if (!memcmp(outbuf,partnumbers_4g[i],6)) |
| return 4096; |
| } |
| |
| /* congatec PN 016203, 616300 has 512MiB of RAM */ |
| arraysize = sizeof(partnumbers_512m) / sizeof(partnumbers_512m[0]); |
| for (i=0; i < arraysize; i++) { |
| if (!memcmp(outbuf,partnumbers_512m[i],6)) |
| return 512; |
| } |
| |
| /* default to 1GByte */ |
| return 1024; |
| } |
| |
| void reset_cpu(void) |
| { |
| } |
| |
| int board_spi_cs_gpio(unsigned bus, unsigned cs) |
| { |
| if (bus == 0 && cs == 0) |
| return (SPI1_CS0); |
| else |
| return -1; |
| } |
| |
| static void memory_init(void) { |
| struct spi_flash *spi; |
| u8 width; |
| u32 size; |
| |
| SETUP_IOMUX_PADS(ecspi1_pads); |
| gpio_direction_output(SPI1_CS0, 0); |
| |
| spi = spi_flash_probe(CONFIG_ENV_SPI_BUS, |
| CONFIG_ENV_SPI_CS, |
| CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE); |
| if (!spi) |
| panic("Cannot identify board type: SPI-NOR flash module not detected\n"); |
| |
| /* lock manufacturer area */ |
| spi_flash_protect(spi, CFG_MFG_ADDR_OFFSET, SZ_16K, true); |
| |
| width = is_cpu_type(MXC_CPU_MX6SOLO) ? 32 : 64; |
| size = get_boardmem_size(spi); |
| printf("Detected Memory Size: %u\n", size); |
| |
| spl_dram_init(width, size); |
| } |
| |
| static void ccgr_init(void) |
| { |
| struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; |
| |
| static const uint32_t ccgr0 = |
| MXC_CCM_CCGR0_AIPS_TZ1_MASK | |
| MXC_CCM_CCGR0_AIPS_TZ2_MASK | |
| MXC_CCM_CCGR0_APBHDMA_MASK | |
| MXC_CCM_CCGR0_CAAM_SECURE_MEM_MASK | |
| MXC_CCM_CCGR0_CAAM_WRAPPER_ACLK_MASK | |
| MXC_CCM_CCGR0_CAAM_WRAPPER_IPG_MASK | |
| MXC_CCM_CCGR0_CHEETAH_DBG_CLK_MASK; |
| |
| static const uint32_t ccgr1 = |
| MXC_CCM_CCGR1_ECSPI1S_MASK | |
| MXC_CCM_CCGR1_ENET_MASK | |
| MXC_CCM_CCGR1_EPIT1S_MASK | |
| MXC_CCM_CCGR1_EPIT2S_MASK | |
| MXC_CCM_CCGR1_GPT_BUS_MASK; |
| |
| static const uint32_t ccgr2 = |
| MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK | |
| MXC_CCM_CCGR2_IPMUX1_MASK | |
| MXC_CCM_CCGR2_IPMUX2_MASK | |
| MXC_CCM_CCGR2_IPMUX3_MASK | |
| MXC_CCM_CCGR2_IPSYNC_IP2APB_TZASC1_IPGS_MASK | |
| MXC_CCM_CCGR2_IPSYNC_IP2APB_TZASC2_IPG_MASK | |
| MXC_CCM_CCGR2_IPSYNC_VDOA_IPG_MASTER_CLK_MASK; |
| |
| static const uint32_t ccgr3 = |
| MXC_CCM_CCGR3_MMDC_CORE_ACLK_FAST_CORE_P0_MASK | |
| MXC_CCM_CCGR3_MMDC_CORE_ACLK_FAST_CORE_P1_MASK | |
| MXC_CCM_CCGR3_MMDC_CORE_IPG_CLK_P0_MASK | |
| MXC_CCM_CCGR3_MMDC_CORE_IPG_CLK_P1_MASK | |
| MXC_CCM_CCGR3_OCRAM_MASK; |
| |
| static const uint32_t ccgr4 = |
| MXC_CCM_CCGR4_PL301_MX6QFAST1_S133_MASK | |
| MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK | |
| MXC_CCM_CCGR4_PL301_MX6QPER2_MAINCLK_ENABLE_MASK | |
| MXC_CCM_CCGR4_PWM1_MASK | |
| MXC_CCM_CCGR4_PWM2_MASK | |
| MXC_CCM_CCGR4_PWM3_MASK | |
| MXC_CCM_CCGR4_PWM4_MASK; |
| |
| static const uint32_t ccgr5 = |
| MXC_CCM_CCGR5_ROM_MASK | |
| MXC_CCM_CCGR5_SDMA_MASK | |
| MXC_CCM_CCGR5_UART_MASK | |
| MXC_CCM_CCGR5_UART_SERIAL_MASK; |
| |
| static const uint32_t ccgr6 = |
| MXC_CCM_CCGR6_USBOH3_MASK | |
| MXC_CCM_CCGR6_USDHC1_MASK | |
| MXC_CCM_CCGR6_USDHC2_MASK | |
| MXC_CCM_CCGR6_SIM1_CLK_MASK | |
| MXC_CCM_CCGR6_SIM2_CLK_MASK; |
| |
| writel(ccgr0, &ccm->CCGR0); |
| writel(ccgr1, &ccm->CCGR1); |
| writel(ccgr2, &ccm->CCGR2); |
| writel(ccgr3, &ccm->CCGR3); |
| writel(ccgr4, &ccm->CCGR4); |
| writel(ccgr5, &ccm->CCGR5); |
| writel(ccgr6, &ccm->CCGR6); |
| } |
| |
| void board_init_f(ulong dummy) |
| { |
| /* setup clock gating */ |
| ccgr_init(); |
| |
| /* setup AIPS and disable watchdog */ |
| arch_cpu_init(); |
| |
| /* setup AXI */ |
| gpr_init(); |
| |
| /* |
| * setup poweroff GPIO. This controls system power regulator. Once |
| * the power button is released this must be enabled to keep system |
| * running. Not enabling it (or disabling it later) will turn off |
| * the main system regulator and instantly poweroff the system. We |
| * do this very early, to reduce the time users have to press the |
| * power button. |
| */ |
| SETUP_IOMUX_PADS(poweroff_pads); |
| gpio_direction_output(POWEROFF, 1); |
| |
| /* setup GP timer */ |
| timer_init(); |
| |
| /* iomux */ |
| if (CFG_MXC_UART_BASE == UART2_BASE) |
| SETUP_IOMUX_PADS(uart2_pads); |
| else if (CFG_MXC_UART_BASE == UART3_BASE) |
| SETUP_IOMUX_PADS(uart3_pads); |
| |
| /* UART clocks enabled and gd valid - init serial console */ |
| preloader_console_init(); |
| |
| /* Needed for malloc() [used by SPI] to work in SPL prior to board_init_r() */ |
| spl_init(); |
| |
| /* DDR initialization */ |
| memory_init(); |
| } |
| |
| void spl_board_prepare_for_boot(void) |
| { |
| printf("Load normal U-Boot...\n"); |
| } |
| #endif |