| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (c) 2022 MediaTek Inc. |
| * Author: Sam Shih <sam.shih@mediatek.com> |
| */ |
| |
| /dts-v1/; |
| #include "mt7981.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| model = "mt7981-rfb"; |
| compatible = "mediatek,mt7981", "mediatek,mt7981-rfb"; |
| chosen { |
| stdout-path = &uart0; |
| tick-timer = &timer0; |
| }; |
| |
| memory@40000000 { |
| device_type = "memory"; |
| reg = <0x40000000 0x10000000>; |
| }; |
| |
| reg_3p3v: regulator-3p3v { |
| compatible = "regulator-fixed"; |
| regulator-name = "fixed-3.3V"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| |
| &uart0 { |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart1_pins>; |
| status = "disabled"; |
| }; |
| |
| ð { |
| status = "okay"; |
| mediatek,gmac-id = <0>; |
| phy-mode = "2500base-x"; |
| mediatek,switch = "mt7531"; |
| reset-gpios = <&gpio 39 GPIO_ACTIVE_HIGH>; |
| |
| fixed-link { |
| speed = <2500>; |
| full-duplex; |
| }; |
| }; |
| |
| &pinctrl { |
| spic_pins: spi1-pins-func-1 { |
| mux { |
| function = "spi"; |
| groups = "spi1_1"; |
| }; |
| }; |
| |
| uart1_pins: spi1-pins-func-3 { |
| mux { |
| function = "uart"; |
| groups = "uart1_2"; |
| }; |
| }; |
| |
| /* pin15 as pwm0 */ |
| one_pwm_pins: one-pwm-pins { |
| mux { |
| function = "pwm"; |
| groups = "pwm0_1"; |
| }; |
| }; |
| |
| /* pin15 as pwm0 and pin14 as pwm1 */ |
| two_pwm_pins: two-pwm-pins { |
| mux { |
| function = "pwm"; |
| groups = "pwm0_1", "pwm1_0"; |
| }; |
| }; |
| |
| /* pin15 as pwm0, pin14 as pwm1, pin7 as pwm2 */ |
| three_pwm_pins: three-pwm-pins { |
| mux { |
| function = "pwm"; |
| groups = "pwm0_1", "pwm1_0", "pwm2"; |
| }; |
| }; |
| |
| mmc0_pins_default: mmc0default { |
| mux { |
| function = "flash"; |
| groups = "emmc_45"; |
| }; |
| conf-cmd-dat { |
| pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO", |
| "SPI0_CS", "SPI0_HOLD", "SPI0_WP", |
| "SPI1_CLK", "SPI1_MOSI", "SPI1_MISO"; |
| input-enable; |
| drive-strength = <MTK_DRIVE_4mA>; |
| bias-pull-up = <MTK_PUPD_SET_R1R0_01>; |
| }; |
| conf-clk { |
| pins = "SPI1_CS"; |
| drive-strength = <MTK_DRIVE_6mA>; |
| bias-pull-down = <MTK_PUPD_SET_R1R0_10>; |
| }; |
| conf-rst { |
| pins = "PWM0"; |
| drive-strength = <MTK_DRIVE_4mA>; |
| bias-pull-up = <MTK_PUPD_SET_R1R0_01>; |
| }; |
| }; |
| }; |
| |
| &pwm { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&two_pwm_pins>; |
| status = "okay"; |
| }; |
| |
| &watchdog { |
| status = "disabled"; |
| }; |
| |
| &mmc0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc0_pins_default>; |
| bus-width = <8>; |
| max-frequency = <52000000>; |
| cap-mmc-highspeed; |
| cap-mmc-hw-reset; |
| vmmc-supply = <®_3p3v>; |
| non-removable; |
| status = "okay"; |
| }; |