blob: f04129fd0429df7ea1455acd8f7ac28a21e3340f [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2011 - 2015 Xilinx
* Copyright (C) 2012 National Instruments Corp.
*/
/dts-v1/;
#include "zynq-7000.dtsi"
/ {
model = "Xilinx ZC702 board";
compatible = "xlnx,zynq-zc702", "xlnx,zynq-7000";
aliases {
ethernet0 = &gem0;
i2c0 = &i2c0;
serial0 = &uart1;
spi0 = &qspi;
mmc0 = &sdhci0;
usb0 = &usb0;
nvmem0 = &eeprom;
rtc0 = &rtc;
};
memory@0 {
device_type = "memory";
reg = <0x0 0x40000000>;
};
chosen {
bootargs = "";
stdout-path = "serial0:115200n8";
};
gpio-keys {
compatible = "gpio-keys";
autorepeat;
sw14 {
label = "sw14";
gpios = <&gpio0 12 0>;
linux,code = <108>; /* down */
wakeup-source;
autorepeat;
};
sw13 {
label = "sw13";
gpios = <&gpio0 14 0>;
linux,code = <103>; /* up */
wakeup-source;
autorepeat;
};
};
leds {
compatible = "gpio-leds";
led-ds23 {
label = "ds23";
gpios = <&gpio0 10 0>;
linux,default-trigger = "heartbeat";
};
};
usb_phy0: phy0 {
compatible = "usb-nop-xceiv";
#phy-cells = <0>;
};
};
&can0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_can0_default>;
};
&clkc {
ps-clk-frequency = <33333333>;
};
&gem0 {
status = "okay";
phy-mode = "rgmii-id";
phy-handle = <&ethernet_phy>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gem0_default>;
phy-reset-gpio = <&gpio0 11 0>;
phy-reset-active-low;
ethernet_phy: ethernet-phy@7 {
reg = <7>;
device_type = "ethernet-phy";
};
};
&gpio0 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpio0_default>;
};
&i2c0 {
status = "okay";
clock-frequency = <400000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c0_default>;
pinctrl-1 = <&pinctrl_i2c0_gpio>;
scl-gpios = <&gpio0 50 0>;
sda-gpios = <&gpio0 51 0>;
i2c-mux@74 {
compatible = "nxp,pca9548";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x74>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
si570: clock-generator@5d {
#clock-cells = <0>;
compatible = "silabs,si570";
temperature-stability = <50>;
reg = <0x5d>;
factory-fout = <156250000>;
clock-frequency = <148500000>;
};
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
adv7511: hdmi-tx@39 {
compatible = "adi,adv7511";
reg = <0x39>;
adi,input-depth = <8>;
adi,input-colorspace = "yuv422";
adi,input-clock = "1x";
adi,input-style = <3>;
adi,input-justification = "right";
};
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
eeprom: eeprom@54 {
compatible = "atmel,24c08";
reg = <0x54>;
};
};
i2c@3 {
#address-cells = <1>;
#size-cells = <0>;
reg = <3>;
gpio@21 {
compatible = "ti,tca6416";
reg = <0x21>;
gpio-controller;
#gpio-cells = <2>;
};
};
i2c@4 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
rtc: rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
};
};
i2c@7 {
#address-cells = <1>;
#size-cells = <0>;
reg = <7>;
hwmon@34 {
compatible = "ti,ucd9248";
reg = <0x34>;
};
hwmon@35 {
compatible = "ti,ucd9248";
reg = <0x35>;
};
hwmon@36 {
compatible = "ti,ucd9248";
reg = <0x36>;
};
};
};
};
&pinctrl0 {
pinctrl_can0_default: can0-default {
mux {
function = "can0";
groups = "can0_9_grp";
};
conf {
groups = "can0_9_grp";
slew-rate = <0>;
power-source = <1>;
};
conf-rx {
pins = "MIO46";
bias-high-impedance;
};
conf-tx {
pins = "MIO47";
bias-disable;
};
};
pinctrl_gem0_default: gem0-default {
mux {
function = "ethernet0";
groups = "ethernet0_0_grp";
};
conf {
groups = "ethernet0_0_grp";
slew-rate = <0>;
power-source = <4>;
};
conf-rx {
pins = "MIO22", "MIO23", "MIO24", "MIO25", "MIO26", "MIO27";
bias-high-impedance;
low-power-disable;
};
conf-tx {
pins = "MIO16", "MIO17", "MIO18", "MIO19", "MIO20", "MIO21";
bias-disable;
low-power-enable;
};
mux-mdio {
function = "mdio0";
groups = "mdio0_0_grp";
};
conf-mdio {
groups = "mdio0_0_grp";
slew-rate = <0>;
power-source = <1>;
bias-disable;
};
};
pinctrl_gpio0_default: gpio0-default {
mux {
function = "gpio0";
groups = "gpio0_7_grp", "gpio0_8_grp", "gpio0_9_grp",
"gpio0_10_grp", "gpio0_11_grp", "gpio0_12_grp",
"gpio0_13_grp", "gpio0_14_grp";
};
conf {
groups = "gpio0_7_grp", "gpio0_8_grp", "gpio0_9_grp",
"gpio0_10_grp", "gpio0_11_grp", "gpio0_12_grp",
"gpio0_13_grp", "gpio0_14_grp";
slew-rate = <0>;
power-source = <1>;
};
conf-pull-up {
pins = "MIO9", "MIO10", "MIO11", "MIO12", "MIO13", "MIO14";
bias-pull-up;
};
conf-pull-none {
pins = "MIO7", "MIO8";
bias-disable;
};
};
pinctrl_i2c0_default: i2c0-default {
mux {
groups = "i2c0_10_grp";
function = "i2c0";
};
conf {
groups = "i2c0_10_grp";
bias-pull-up;
slew-rate = <0>;
power-source = <1>;
};
};
pinctrl_i2c0_gpio: i2c0-gpio {
mux {
groups = "gpio0_50_grp", "gpio0_51_grp";
function = "gpio0";
};
conf {
groups = "gpio0_50_grp", "gpio0_51_grp";
slew-rate = <0>;
power-source = <1>;
};
};
pinctrl_sdhci0_default: sdhci0-default {
mux {
groups = "sdio0_2_grp";
function = "sdio0";
};
conf {
groups = "sdio0_2_grp";
slew-rate = <0>;
power-source = <1>;
bias-disable;
};
mux-cd {
groups = "gpio0_0_grp";
function = "sdio0_cd";
};
conf-cd {
groups = "gpio0_0_grp";
bias-high-impedance;
bias-pull-up;
slew-rate = <0>;
power-source = <1>;
};
mux-wp {
groups = "gpio0_15_grp";
function = "sdio0_wp";
};
conf-wp {
groups = "gpio0_15_grp";
bias-high-impedance;
bias-pull-up;
slew-rate = <0>;
power-source = <1>;
};
};
pinctrl_uart1_default: uart1-default {
mux {
groups = "uart1_10_grp";
function = "uart1";
};
conf {
groups = "uart1_10_grp";
slew-rate = <0>;
power-source = <1>;
};
conf-rx {
pins = "MIO49";
bias-high-impedance;
};
conf-tx {
pins = "MIO48";
bias-disable;
};
};
pinctrl_usb0_default: usb0-default {
mux {
groups = "usb0_0_grp";
function = "usb0";
};
conf {
groups = "usb0_0_grp";
slew-rate = <0>;
power-source = <1>;
};
conf-rx {
pins = "MIO29", "MIO31", "MIO36";
bias-high-impedance;
};
conf-tx {
pins = "MIO28", "MIO30", "MIO32", "MIO33", "MIO34",
"MIO35", "MIO37", "MIO38", "MIO39";
bias-disable;
};
};
};
&qspi {
u-boot,dm-pre-reloc;
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "n25q128a11", "jedec,spi-nor";
reg = <0x0>;
spi-tx-bus-width = <1>;
spi-rx-bus-width = <4>;
spi-max-frequency = <50000000>;
};
};
&sdhci0 {
u-boot,dm-pre-reloc;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sdhci0_default>;
};
&uart1 {
u-boot,dm-pre-reloc;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1_default>;
};
&usb0 {
status = "okay";
dr_mode = "host";
usb-phy = <&usb_phy0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
};