include/configs/j721s2_evm.h - platform/external/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Configuration header file for K3 J721S2 EVM
  *
  * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
  *	David Huang <d-huang@ti.com>
  */

 #ifndef __CONFIG_J721S2_EVM_H
 #define __CONFIG_J721S2_EVM_H

 #include <linux/sizes.h>
 #include <config_distro_bootcmd.h>
 #include <environment/ti/mmc.h>
 #include <environment/ti/k3_rproc.h>
 #include <environment/ti/ufs.h>
 #include <environment/ti/k3_dfu.h>

 /* DDR Configuration */
 #define CONFIG_SYS_SDRAM_BASE1		0x880000000

 /* SPL Loader Configuration */
 #if defined(CONFIG_TARGET_J721S2_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SPL_TEXT_BASE +	\
 					 CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE)
 #define CONFIG_SYS_UBOOT_BASE		0x50280000
 /* Image load address in RAM for DFU boot*/
 #else
 #define CONFIG_SYS_UBOOT_BASE		0x50080000
 /*
  * Maximum size in memory allocated to the SPL BSS. Keep it as tight as
  * possible (to allow the build to go through), as this directly affects
  * our memory footprint. The less we use for BSS the more we have available
  * for everything else.
  */
 #define CONFIG_SPL_BSS_MAX_SIZE		0xA000
 /*
  * Link BSS to be within SPL in a dedicated region located near the top of
  * the MCU SRAM, this way making it available also before relocation. Note
  * that we are not using the actual top of the MCU SRAM as there is a memory
  * location filled in by the boot ROM that we want to read out without any
  * interference from the C context.
  */
 #define CONFIG_SPL_BSS_START_ADDR	(0x41c80000 -\
 					 CONFIG_SPL_BSS_MAX_SIZE)
 /* Set the stack right below the SPL BSS section */
 #define CONFIG_SYS_INIT_SP_ADDR         CONFIG_SPL_BSS_START_ADDR
 /* Configure R5 SPL post-relocation malloc pool in DDR */
 #define CONFIG_SYS_SPL_MALLOC_START	0x84000000
 #define CONFIG_SYS_SPL_MALLOC_SIZE	SZ_16M
 /* Image load address in RAM for DFU boot*/
 #endif

 #ifdef CONFIG_SYS_K3_SPL_ATF
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME	"tispl.bin"
 #endif

 #define CONFIG_SPL_MAX_SIZE		CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE

 #define CONFIG_SYS_BOOTM_LEN		SZ_64M

 /* U-Boot general configuration */
 #define EXTRA_ENV_J721S2_BOARD_SETTINGS					\
 	"default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0"	\
 	"findfdt="							\
 		"setenv name_fdt ${default_device_tree};"		\
 		"setenv fdtfile ${name_fdt}\0"				\
 	"name_kern=Image\0"						\
 	"console=ttyS2,115200n8\0"					\
 	"args_all=setenv optargs earlycon=ns16550a,mmio32,0x02880000 "	\
 		"${mtdparts}\0"						\
 	"run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0"

 #define PARTS_DEFAULT \
 	/* Linux partitions */ \
 	"uuid_disk=${uuid_gpt_disk};" \
 	"name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0"

 #ifdef CONFIG_SYS_K3_SPL_ATF
 #if defined(CONFIG_TARGET_J721S2_R5_EVM)
 #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC				\
 	"addr_mcur5f0_0load=0x89000000\0"				\
 	"name_mcur5f0_0fw=/lib/firmware/j7-mcu-r5f0_0-fw\0"
 #elif defined(CONFIG_TARGET_J7200_R5_EVM)
 #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC				\
 	"addr_mcur5f0_0load=0x89000000\0"				\
 	"name_mcur5f0_0fw=/lib/firmware/j7200-mcu-r5f0_0-fw\0"
 #endif /* CONFIG_TARGET_J721S2_R5_EVM */
 #else
 #define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC ""
 #endif /* CONFIG_SYS_K3_SPL_ATF */

 /* U-Boot MMC-specific configuration */
 #define EXTRA_ENV_J721S2_BOARD_SETTINGS_MMC				\
 	"boot=mmc\0"							\
 	"mmcdev=1\0"							\
 	"bootpart=1:2\0"						\
 	"bootdir=/boot\0"						\
 	EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC				\
 	"rd_spec=-\0"							\
 	"init_mmc=run args_all args_mmc\0"				\
 	"get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \
 	"get_overlay_mmc="						\
 		"fdt address ${fdtaddr};"				\
 		"fdt resize 0x100000;"					\
 		"for overlay in $name_overlays;"			\
 		"do;"							\
 		"load mmc ${bootpart} ${dtboaddr} ${bootdir}/${overlay} && "	\
 		"fdt apply ${dtboaddr};"				\
 		"done;\0"						\
 	"partitions=" PARTS_DEFAULT					\
 	"get_kern_mmc=load mmc ${bootpart} ${loadaddr} "		\
 		"${bootdir}/${name_kern}\0"				\
 	"get_fit_mmc=load mmc ${bootpart} ${addr_fit} "			\
 		"${bootdir}/${name_fit}\0"				\
 	"partitions=" PARTS_DEFAULT

 /* Set the default list of remote processors to boot */
 #if defined(CONFIG_TARGET_J721S2_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
 #ifdef DEFAULT_RPROCS
 #undef DEFAULT_RPROCS
 #endif
 #endif

 #ifdef CONFIG_TARGET_J721S2_A72_EVM
 #define DEFAULT_RPROCS	""						\
 		"2 /lib/firmware/j721s2-main-r5f0_0-fw "			\
 		"3 /lib/firmware/j721s2-main-r5f0_1-fw "			\
 		"4 /lib/firmware/j721s2-main-r5f1_0-fw "			\
 		"5 /lib/firmware/j721s2-main-r5f1_1-fw "			\
 		"6 /lib/firmware/j721s2-c71_0-fw "				\
 		"7 /lib/firmware/j721s2-c71_1-fw "
 #endif /* CONFIG_TARGET_J721S2_A72_EVM */

 #ifdef CONFIG_TARGET_J7200_A72_EVM
 #define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY				\
 	"do_main_cpsw0_qsgmii_phyinit=1\0"				\
 	"init_main_cpsw0_qsgmii_phy=gpio set gpio@22_17;"		\
 		 "gpio clear gpio@22_16\0"				\
 	"main_cpsw0_qsgmii_phyinit="					\
 	"if test ${do_main_cpsw0_qsgmii_phyinit} -eq 1 && test ${dorprocboot} -eq 1 && " \
 			"test ${boot} = mmc; then "			\
 		"run init_main_cpsw0_qsgmii_phy;"			\
 	"fi;\0"
 #define DEFAULT_RPROCS ""						\
 		"2 /lib/firmware/j7200-main-r5f0_0-fw "			\
 		"3 /lib/firmware/j7200-main-r5f0_1-fw "
 #endif /* CONFIG_TARGET_J7200_A72_EVM */

 #ifndef EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
 #define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
 #endif

 /* set default dfu_bufsiz to 128KB (sector size of OSPI) */
 #define EXTRA_ENV_DFUARGS \
 	DFU_ALT_INFO_MMC \
 	DFU_ALT_INFO_EMMC \
 	DFU_ALT_INFO_RAM \
 	DFU_ALT_INFO_OSPI

 #if defined(CONFIG_TARGET_J721S2_A72_EVM) || defined(CONFIG_TARGET_J7200_A72_EVM)
 #define EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD				\
 	"mtdids=" CONFIG_MTDIDS_DEFAULT "\0"				\
 	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"
 #else
 #define EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD
 #endif

 /* Incorporate settings into the U-Boot environment */
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	DEFAULT_LINUX_BOOT_ENV						\
 	DEFAULT_MMC_TI_ARGS						\
 	DEFAULT_FIT_TI_ARGS						\
 	EXTRA_ENV_J721S2_BOARD_SETTINGS					\
 	EXTRA_ENV_J721S2_BOARD_SETTINGS_MMC				\
 	EXTRA_ENV_RPROC_SETTINGS					\
 	EXTRA_ENV_DFUARGS						\
 	DEFAULT_UFS_TI_ARGS						\
 	EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD				\
 	EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY

 /* Now for the remaining common defines */
 #include <configs/ti_armv7_common.h>

 /* MMC ENV related defines */

 #endif /* __CONFIG_J721S2_EVM_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Configuration header file for K3 J721S2 EVM
	*
	* Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
	* David Huang <d-huang@ti.com>
	*/

	#ifndef __CONFIG_J721S2_EVM_H
	#define __CONFIG_J721S2_EVM_H

	#include <linux/sizes.h>
	#include <config_distro_bootcmd.h>
	#include <environment/ti/mmc.h>
	#include <environment/ti/k3_rproc.h>
	#include <environment/ti/ufs.h>
	#include <environment/ti/k3_dfu.h>

	/* DDR Configuration */
	#define CONFIG_SYS_SDRAM_BASE1 0x880000000

	/* SPL Loader Configuration */
	#if defined(CONFIG_TARGET_J721S2_A72_EVM) \|\| defined(CONFIG_TARGET_J7200_A72_EVM)
	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SPL_TEXT_BASE + \
	CONFIG_SYS_K3_NON_SECURE_MSRAM_SIZE)
	#define CONFIG_SYS_UBOOT_BASE 0x50280000
	/* Image load address in RAM for DFU boot*/
	#else
	#define CONFIG_SYS_UBOOT_BASE 0x50080000
	/*
	* Maximum size in memory allocated to the SPL BSS. Keep it as tight as
	* possible (to allow the build to go through), as this directly affects
	* our memory footprint. The less we use for BSS the more we have available
	* for everything else.
	*/
	#define CONFIG_SPL_BSS_MAX_SIZE 0xA000
	/*
	* Link BSS to be within SPL in a dedicated region located near the top of
	* the MCU SRAM, this way making it available also before relocation. Note
	* that we are not using the actual top of the MCU SRAM as there is a memory
	* location filled in by the boot ROM that we want to read out without any
	* interference from the C context.
	*/
	#define CONFIG_SPL_BSS_START_ADDR (0x41c80000 -\
	CONFIG_SPL_BSS_MAX_SIZE)
	/* Set the stack right below the SPL BSS section */
	#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SPL_BSS_START_ADDR
	/* Configure R5 SPL post-relocation malloc pool in DDR */
	#define CONFIG_SYS_SPL_MALLOC_START 0x84000000
	#define CONFIG_SYS_SPL_MALLOC_SIZE SZ_16M
	/* Image load address in RAM for DFU boot*/
	#endif

	#ifdef CONFIG_SYS_K3_SPL_ATF
	#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "tispl.bin"
	#endif

	#define CONFIG_SPL_MAX_SIZE CONFIG_SYS_K3_MAX_DOWNLODABLE_IMAGE_SIZE

	#define CONFIG_SYS_BOOTM_LEN SZ_64M

	/* U-Boot general configuration */
	#define EXTRA_ENV_J721S2_BOARD_SETTINGS \
	"default_device_tree=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
	"findfdt=" \
	"setenv name_fdt ${default_device_tree};" \
	"setenv fdtfile ${name_fdt}\0" \
	"name_kern=Image\0" \
	"console=ttyS2,115200n8\0" \
	"args_all=setenv optargs earlycon=ns16550a,mmio32,0x02880000 " \
	"${mtdparts}\0" \
	"run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}\0"

	#define PARTS_DEFAULT \
	/* Linux partitions */ \
	"uuid_disk=${uuid_gpt_disk};" \
	"name=rootfs,start=0,size=-,uuid=${uuid_gpt_rootfs}\0"

	#ifdef CONFIG_SYS_K3_SPL_ATF
	#if defined(CONFIG_TARGET_J721S2_R5_EVM)
	#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \
	"addr_mcur5f0_0load=0x89000000\0" \
	"name_mcur5f0_0fw=/lib/firmware/j7-mcu-r5f0_0-fw\0"
	#elif defined(CONFIG_TARGET_J7200_R5_EVM)
	#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \
	"addr_mcur5f0_0load=0x89000000\0" \
	"name_mcur5f0_0fw=/lib/firmware/j7200-mcu-r5f0_0-fw\0"
	#endif /* CONFIG_TARGET_J721S2_R5_EVM */
	#else
	#define EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC ""
	#endif /* CONFIG_SYS_K3_SPL_ATF */

	/* U-Boot MMC-specific configuration */
	#define EXTRA_ENV_J721S2_BOARD_SETTINGS_MMC \
	"boot=mmc\0" \
	"mmcdev=1\0" \
	"bootpart=1:2\0" \
	"bootdir=/boot\0" \
	EXTRA_ENV_R5_SPL_RPROC_FW_ARGS_MMC \
	"rd_spec=-\0" \
	"init_mmc=run args_all args_mmc\0" \
	"get_fdt_mmc=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${name_fdt}\0" \
	"get_overlay_mmc=" \
	"fdt address ${fdtaddr};" \
	"fdt resize 0x100000;" \
	"for overlay in $name_overlays;" \
	"do;" \
	"load mmc ${bootpart} ${dtboaddr} ${bootdir}/${overlay} && " \
	"fdt apply ${dtboaddr};" \
	"done;\0" \
	"partitions=" PARTS_DEFAULT \
	"get_kern_mmc=load mmc ${bootpart} ${loadaddr} " \
	"${bootdir}/${name_kern}\0" \
	"get_fit_mmc=load mmc ${bootpart} ${addr_fit} " \
	"${bootdir}/${name_fit}\0" \
	"partitions=" PARTS_DEFAULT

	/* Set the default list of remote processors to boot */
	#if defined(CONFIG_TARGET_J721S2_A72_EVM) \|\| defined(CONFIG_TARGET_J7200_A72_EVM)
	#ifdef DEFAULT_RPROCS
	#undef DEFAULT_RPROCS
	#endif
	#endif

	#ifdef CONFIG_TARGET_J721S2_A72_EVM
	#define DEFAULT_RPROCS "" \
	"2 /lib/firmware/j721s2-main-r5f0_0-fw " \
	"3 /lib/firmware/j721s2-main-r5f0_1-fw " \
	"4 /lib/firmware/j721s2-main-r5f1_0-fw " \
	"5 /lib/firmware/j721s2-main-r5f1_1-fw " \
	"6 /lib/firmware/j721s2-c71_0-fw " \
	"7 /lib/firmware/j721s2-c71_1-fw "
	#endif /* CONFIG_TARGET_J721S2_A72_EVM */

	#ifdef CONFIG_TARGET_J7200_A72_EVM
	#define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY \
	"do_main_cpsw0_qsgmii_phyinit=1\0" \
	"init_main_cpsw0_qsgmii_phy=gpio set gpio@22_17;" \
	"gpio clear gpio@22_16\0" \
	"main_cpsw0_qsgmii_phyinit=" \
	"if test ${do_main_cpsw0_qsgmii_phyinit} -eq 1 && test ${dorprocboot} -eq 1 && " \
	"test ${boot} = mmc; then " \
	"run init_main_cpsw0_qsgmii_phy;" \
	"fi;\0"
	#define DEFAULT_RPROCS "" \
	"2 /lib/firmware/j7200-main-r5f0_0-fw " \
	"3 /lib/firmware/j7200-main-r5f0_1-fw "
	#endif /* CONFIG_TARGET_J7200_A72_EVM */

	#ifndef EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
	#define EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY
	#endif

	/* set default dfu_bufsiz to 128KB (sector size of OSPI) */
	#define EXTRA_ENV_DFUARGS \
	DFU_ALT_INFO_MMC \
	DFU_ALT_INFO_EMMC \
	DFU_ALT_INFO_RAM \
	DFU_ALT_INFO_OSPI

	#if defined(CONFIG_TARGET_J721S2_A72_EVM) \|\| defined(CONFIG_TARGET_J7200_A72_EVM)
	#define EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD \
	"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0"
	#else
	#define EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD
	#endif

	/* Incorporate settings into the U-Boot environment */
	#define CONFIG_EXTRA_ENV_SETTINGS \
	DEFAULT_LINUX_BOOT_ENV \
	DEFAULT_MMC_TI_ARGS \
	DEFAULT_FIT_TI_ARGS \
	EXTRA_ENV_J721S2_BOARD_SETTINGS \
	EXTRA_ENV_J721S2_BOARD_SETTINGS_MMC \
	EXTRA_ENV_RPROC_SETTINGS \
	EXTRA_ENV_DFUARGS \
	DEFAULT_UFS_TI_ARGS \
	EXTRA_ENV_J721S2_BOARD_SETTINGS_MTD \
	EXTRA_ENV_CONFIG_MAIN_CPSW0_QSGMII_PHY

	/* Now for the remaining common defines */
	#include <configs/ti_armv7_common.h>

	/* MMC ENV related defines */

	#endif /* __CONFIG_J721S2_EVM_H */