| /* |
| * NVIDIA Tegra SPI controller (T114 and later) |
| * |
| * Copyright (c) 2010-2013 NVIDIA Corporation |
| * |
| * See file CREDITS for list of people who contributed to this |
| * project. |
| * |
| * This software is licensed under the terms of the GNU General Public |
| * License version 2, as published by the Free Software Foundation, and |
| * may be copied, distributed, and modified under those terms. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #include <common.h> |
| #include <malloc.h> |
| #include <asm/io.h> |
| #include <asm/gpio.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch-tegra/clk_rst.h> |
| #include <asm/arch-tegra114/tegra114_spi.h> |
| #include <spi.h> |
| #include <fdtdec.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| /* COMMAND1 */ |
| #define SPI_CMD1_GO (1 << 31) |
| #define SPI_CMD1_M_S (1 << 30) |
| #define SPI_CMD1_MODE_MASK 0x3 |
| #define SPI_CMD1_MODE_SHIFT 28 |
| #define SPI_CMD1_CS_SEL_MASK 0x3 |
| #define SPI_CMD1_CS_SEL_SHIFT 26 |
| #define SPI_CMD1_CS_POL_INACTIVE3 (1 << 25) |
| #define SPI_CMD1_CS_POL_INACTIVE2 (1 << 24) |
| #define SPI_CMD1_CS_POL_INACTIVE1 (1 << 23) |
| #define SPI_CMD1_CS_POL_INACTIVE0 (1 << 22) |
| #define SPI_CMD1_CS_SW_HW (1 << 21) |
| #define SPI_CMD1_CS_SW_VAL (1 << 20) |
| #define SPI_CMD1_IDLE_SDA_MASK 0x3 |
| #define SPI_CMD1_IDLE_SDA_SHIFT 18 |
| #define SPI_CMD1_BIDIR (1 << 17) |
| #define SPI_CMD1_LSBI_FE (1 << 16) |
| #define SPI_CMD1_LSBY_FE (1 << 15) |
| #define SPI_CMD1_BOTH_EN_BIT (1 << 14) |
| #define SPI_CMD1_BOTH_EN_BYTE (1 << 13) |
| #define SPI_CMD1_RX_EN (1 << 12) |
| #define SPI_CMD1_TX_EN (1 << 11) |
| #define SPI_CMD1_PACKED (1 << 5) |
| #define SPI_CMD1_BIT_LEN_MASK 0x1F |
| #define SPI_CMD1_BIT_LEN_SHIFT 0 |
| |
| /* COMMAND2 */ |
| #define SPI_CMD2_TX_CLK_TAP_DELAY (1 << 6) |
| #define SPI_CMD2_TX_CLK_TAP_DELAY_MASK (0x3F << 6) |
| #define SPI_CMD2_RX_CLK_TAP_DELAY (1 << 0) |
| #define SPI_CMD2_RX_CLK_TAP_DELAY_MASK (0x3F << 0) |
| |
| /* TRANSFER STATUS */ |
| #define SPI_XFER_STS_RDY (1 << 30) |
| |
| /* FIFO STATUS */ |
| #define SPI_FIFO_STS_CS_INACTIVE (1 << 31) |
| #define SPI_FIFO_STS_FRAME_END (1 << 30) |
| #define SPI_FIFO_STS_RX_FIFO_FLUSH (1 << 15) |
| #define SPI_FIFO_STS_TX_FIFO_FLUSH (1 << 14) |
| #define SPI_FIFO_STS_ERR (1 << 8) |
| #define SPI_FIFO_STS_TX_FIFO_OVF (1 << 7) |
| #define SPI_FIFO_STS_TX_FIFO_UNR (1 << 6) |
| #define SPI_FIFO_STS_RX_FIFO_OVF (1 << 5) |
| #define SPI_FIFO_STS_RX_FIFO_UNR (1 << 4) |
| #define SPI_FIFO_STS_TX_FIFO_FULL (1 << 3) |
| #define SPI_FIFO_STS_TX_FIFO_EMPTY (1 << 2) |
| #define SPI_FIFO_STS_RX_FIFO_FULL (1 << 1) |
| #define SPI_FIFO_STS_RX_FIFO_EMPTY (1 << 0) |
| |
| #define SPI_TIMEOUT 1000 |
| #define TEGRA_SPI_MAX_FREQ 52000000 |
| |
| struct spi_regs { |
| u32 command1; /* 000:SPI_COMMAND1 register */ |
| u32 command2; /* 004:SPI_COMMAND2 register */ |
| u32 timing1; /* 008:SPI_CS_TIM1 register */ |
| u32 timing2; /* 00c:SPI_CS_TIM2 register */ |
| u32 xfer_status;/* 010:SPI_TRANS_STATUS register */ |
| u32 fifo_status;/* 014:SPI_FIFO_STATUS register */ |
| u32 tx_data; /* 018:SPI_TX_DATA register */ |
| u32 rx_data; /* 01c:SPI_RX_DATA register */ |
| u32 dma_ctl; /* 020:SPI_DMA_CTL register */ |
| u32 dma_blk; /* 024:SPI_DMA_BLK register */ |
| u32 rsvd[56]; /* 028-107 reserved */ |
| u32 tx_fifo; /* 108:SPI_FIFO1 register */ |
| u32 rsvd2[31]; /* 10c-187 reserved */ |
| u32 rx_fifo; /* 188:SPI_FIFO2 register */ |
| u32 spare_ctl; /* 18c:SPI_SPARE_CTRL register */ |
| }; |
| |
| struct tegra_spi_ctrl { |
| struct spi_regs *regs; |
| unsigned int freq; |
| unsigned int mode; |
| int periph_id; |
| int valid; |
| }; |
| |
| struct tegra_spi_slave { |
| struct spi_slave slave; |
| struct tegra_spi_ctrl *ctrl; |
| }; |
| |
| static struct tegra_spi_ctrl spi_ctrls[CONFIG_TEGRA114_SPI_CTRLS]; |
| |
| static inline struct tegra_spi_slave *to_tegra_spi(struct spi_slave *slave) |
| { |
| return container_of(slave, struct tegra_spi_slave, slave); |
| } |
| |
| int tegra114_spi_cs_is_valid(unsigned int bus, unsigned int cs) |
| { |
| if (bus >= CONFIG_TEGRA114_SPI_CTRLS || cs > 3 || !spi_ctrls[bus].valid) |
| return 0; |
| else |
| return 1; |
| } |
| |
| struct spi_slave *tegra114_spi_setup_slave(unsigned int bus, unsigned int cs, |
| unsigned int max_hz, unsigned int mode) |
| { |
| struct tegra_spi_slave *spi; |
| |
| debug("%s: bus: %u, cs: %u, max_hz: %u, mode: %u\n", __func__, |
| bus, cs, max_hz, mode); |
| |
| if (!spi_cs_is_valid(bus, cs)) { |
| printf("SPI error: unsupported bus %d / chip select %d\n", |
| bus, cs); |
| return NULL; |
| } |
| |
| if (max_hz > TEGRA_SPI_MAX_FREQ) { |
| printf("SPI error: unsupported frequency %d Hz. Max frequency" |
| " is %d Hz\n", max_hz, TEGRA_SPI_MAX_FREQ); |
| return NULL; |
| } |
| |
| spi = spi_alloc_slave(struct tegra_spi_slave, bus, cs); |
| if (!spi) { |
| printf("SPI error: malloc of SPI structure failed\n"); |
| return NULL; |
| } |
| spi->ctrl = &spi_ctrls[bus]; |
| if (!spi->ctrl) { |
| printf("SPI error: could not find controller for bus %d\n", |
| bus); |
| return NULL; |
| } |
| |
| if (max_hz < spi->ctrl->freq) { |
| debug("%s: limiting frequency from %u to %u\n", __func__, |
| spi->ctrl->freq, max_hz); |
| spi->ctrl->freq = max_hz; |
| } |
| spi->ctrl->mode = mode; |
| |
| return &spi->slave; |
| } |
| |
| void tegra114_spi_free_slave(struct spi_slave *slave) |
| { |
| struct tegra_spi_slave *spi = to_tegra_spi(slave); |
| |
| free(spi); |
| } |
| |
| int tegra114_spi_init(int *node_list, int count) |
| { |
| struct tegra_spi_ctrl *ctrl; |
| int i; |
| int node = 0; |
| int found = 0; |
| |
| for (i = 0; i < count; i++) { |
| ctrl = &spi_ctrls[i]; |
| node = node_list[i]; |
| |
| ctrl->regs = (struct spi_regs *)fdtdec_get_addr(gd->fdt_blob, |
| node, "reg"); |
| if ((fdt_addr_t)ctrl->regs == FDT_ADDR_T_NONE) { |
| debug("%s: no spi register found\n", __func__); |
| continue; |
| } |
| ctrl->freq = fdtdec_get_int(gd->fdt_blob, node, |
| "spi-max-frequency", 0); |
| if (!ctrl->freq) { |
| debug("%s: no spi max frequency found\n", __func__); |
| continue; |
| } |
| |
| ctrl->periph_id = clock_decode_periph_id(gd->fdt_blob, node); |
| if (ctrl->periph_id == PERIPH_ID_NONE) { |
| debug("%s: could not decode periph id\n", __func__); |
| continue; |
| } |
| ctrl->valid = 1; |
| found = 1; |
| |
| debug("%s: found controller at %p, freq = %u, periph_id = %d\n", |
| __func__, ctrl->regs, ctrl->freq, ctrl->periph_id); |
| } |
| |
| return !found; |
| } |
| |
| int tegra114_spi_claim_bus(struct spi_slave *slave) |
| { |
| struct tegra_spi_slave *spi = to_tegra_spi(slave); |
| struct spi_regs *regs = spi->ctrl->regs; |
| |
| /* Change SPI clock to correct frequency, PLLP_OUT0 source */ |
| clock_start_periph_pll(spi->ctrl->periph_id, CLOCK_ID_PERIPH, |
| spi->ctrl->freq); |
| |
| /* Clear stale status here */ |
| setbits_le32(®s->fifo_status, |
| SPI_FIFO_STS_ERR | |
| SPI_FIFO_STS_TX_FIFO_OVF | |
| SPI_FIFO_STS_TX_FIFO_UNR | |
| SPI_FIFO_STS_RX_FIFO_OVF | |
| SPI_FIFO_STS_RX_FIFO_UNR | |
| SPI_FIFO_STS_TX_FIFO_FULL | |
| SPI_FIFO_STS_TX_FIFO_EMPTY | |
| SPI_FIFO_STS_RX_FIFO_FULL | |
| SPI_FIFO_STS_RX_FIFO_EMPTY); |
| debug("%s: FIFO STATUS = %08x\n", __func__, readl(®s->fifo_status)); |
| |
| /* Set master mode and sw controlled CS */ |
| setbits_le32(®s->command1, SPI_CMD1_M_S | SPI_CMD1_CS_SW_HW | |
| (spi->ctrl->mode << SPI_CMD1_MODE_SHIFT)); |
| debug("%s: COMMAND1 = %08x\n", __func__, readl(®s->command1)); |
| |
| return 0; |
| } |
| |
| void tegra114_spi_cs_activate(struct spi_slave *slave) |
| { |
| struct tegra_spi_slave *spi = to_tegra_spi(slave); |
| struct spi_regs *regs = spi->ctrl->regs; |
| |
| clrbits_le32(®s->command1, SPI_CMD1_CS_SW_VAL); |
| } |
| |
| void tegra114_spi_cs_deactivate(struct spi_slave *slave) |
| { |
| struct tegra_spi_slave *spi = to_tegra_spi(slave); |
| struct spi_regs *regs = spi->ctrl->regs; |
| |
| setbits_le32(®s->command1, SPI_CMD1_CS_SW_VAL); |
| } |
| |
| int tegra114_spi_xfer(struct spi_slave *slave, unsigned int bitlen, |
| const void *data_out, void *data_in, unsigned long flags) |
| { |
| struct tegra_spi_slave *spi = to_tegra_spi(slave); |
| struct spi_regs *regs = spi->ctrl->regs; |
| u32 reg, tmpdout, tmpdin = 0; |
| const u8 *dout = data_out; |
| u8 *din = data_in; |
| int num_bytes; |
| int ret; |
| |
| debug("%s: slave %u:%u dout %p din %p bitlen %u\n", |
| __func__, slave->bus, slave->cs, dout, din, bitlen); |
| if (bitlen % 8) |
| return -1; |
| num_bytes = bitlen / 8; |
| |
| ret = 0; |
| |
| /* clear all error status bits */ |
| reg = readl(®s->fifo_status); |
| writel(reg, ®s->fifo_status); |
| |
| /* clear ready bit */ |
| setbits_le32(®s->xfer_status, SPI_XFER_STS_RDY); |
| |
| clrsetbits_le32(®s->command1, SPI_CMD1_CS_SW_VAL, |
| SPI_CMD1_RX_EN | SPI_CMD1_TX_EN | SPI_CMD1_LSBY_FE | |
| (slave->cs << SPI_CMD1_CS_SEL_SHIFT)); |
| |
| /* set xfer size to 1 block (32 bits) */ |
| writel(0, ®s->dma_blk); |
| |
| if (flags & SPI_XFER_BEGIN) |
| spi_cs_activate(slave); |
| |
| /* handle data in 32-bit chunks */ |
| while (num_bytes > 0) { |
| int bytes; |
| int is_read = 0; |
| int tm, i; |
| |
| tmpdout = 0; |
| bytes = (num_bytes > 4) ? 4 : num_bytes; |
| |
| if (dout != NULL) { |
| for (i = 0; i < bytes; ++i) |
| tmpdout = (tmpdout << 8) | dout[i]; |
| dout += bytes; |
| } |
| |
| num_bytes -= bytes; |
| |
| clrsetbits_le32(®s->command1, |
| SPI_CMD1_BIT_LEN_MASK << SPI_CMD1_BIT_LEN_SHIFT, |
| (bytes * 8 - 1) << SPI_CMD1_BIT_LEN_SHIFT); |
| writel(tmpdout, ®s->tx_fifo); |
| setbits_le32(®s->command1, SPI_CMD1_GO); |
| |
| /* |
| * Wait for SPI transmit FIFO to empty, or to time out. |
| * The RX FIFO status will be read and cleared last |
| */ |
| for (tm = 0, is_read = 0; tm < SPI_TIMEOUT; ++tm) { |
| u32 fifo_status, xfer_status; |
| |
| fifo_status = readl(®s->fifo_status); |
| |
| /* We can exit when we've had both RX and TX activity */ |
| if (is_read && |
| (fifo_status & SPI_FIFO_STS_TX_FIFO_EMPTY)) |
| break; |
| |
| xfer_status = readl(®s->xfer_status); |
| if (!(xfer_status & SPI_XFER_STS_RDY)) |
| continue; |
| |
| if (fifo_status & SPI_FIFO_STS_ERR) { |
| debug("%s: got a fifo error: ", __func__); |
| if (fifo_status & SPI_FIFO_STS_TX_FIFO_OVF) |
| debug("tx FIFO overflow "); |
| if (fifo_status & SPI_FIFO_STS_TX_FIFO_UNR) |
| debug("tx FIFO underrun "); |
| if (fifo_status & SPI_FIFO_STS_RX_FIFO_OVF) |
| debug("rx FIFO overflow "); |
| if (fifo_status & SPI_FIFO_STS_RX_FIFO_UNR) |
| debug("rx FIFO underrun "); |
| if (fifo_status & SPI_FIFO_STS_TX_FIFO_FULL) |
| debug("tx FIFO full "); |
| if (fifo_status & SPI_FIFO_STS_TX_FIFO_EMPTY) |
| debug("tx FIFO empty "); |
| if (fifo_status & SPI_FIFO_STS_RX_FIFO_FULL) |
| debug("rx FIFO full "); |
| if (fifo_status & SPI_FIFO_STS_RX_FIFO_EMPTY) |
| debug("rx FIFO empty "); |
| debug("\n"); |
| break; |
| } |
| |
| if (!(fifo_status & SPI_FIFO_STS_RX_FIFO_EMPTY)) { |
| tmpdin = readl(®s->rx_fifo); |
| is_read = 1; |
| |
| /* swap bytes read in */ |
| if (din != NULL) { |
| for (i = bytes - 1; i >= 0; --i) { |
| din[i] = tmpdin & 0xff; |
| tmpdin >>= 8; |
| } |
| din += bytes; |
| } |
| } |
| } |
| |
| if (tm >= SPI_TIMEOUT) |
| ret = tm; |
| |
| /* clear ACK RDY, etc. bits */ |
| writel(readl(®s->fifo_status), ®s->fifo_status); |
| } |
| |
| if (flags & SPI_XFER_END) |
| spi_cs_deactivate(slave); |
| |
| debug("%s: transfer ended. Value=%08x, fifo_status = %08x\n", |
| __func__, tmpdin, readl(®s->fifo_status)); |
| |
| if (ret) { |
| printf("%s: timeout during SPI transfer, tm %d\n", |
| __func__, ret); |
| return -1; |
| } |
| |
| return 0; |
| } |