WIP: qcom_defconfig: enable rb1, rb2, and rb5
Enable peripherals for these boards as well as UFS and USB
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
diff --git a/configs/qcom_defconfig b/configs/qcom_defconfig
index daabfb0..287009d 100644
--- a/configs/qcom_defconfig
+++ b/configs/qcom_defconfig
@@ -19,35 +19,55 @@
CONFIG_HUSH_PARSER=y
CONFIG_SYS_MAXARGS=64
CONFIG_SYS_CBSIZE=512
+CONFIG_CMD_BOOTEFI_SELFTEST=y
CONFIG_CMD_BOOTMENU=y
+CONFIG_CMD_NVEDIT_EFI=y
CONFIG_CMD_CLK=y
CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
CONFIG_CMD_MMC=y
CONFIG_CMD_PART=y
CONFIG_CMD_UFS=y
CONFIG_CMD_USB=y
CONFIG_CMD_CAT=y
CONFIG_CMD_BMP=y
+CONFIG_CMD_EFIDEBUG=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_CMD_LOG=y
-CONFIG_EFI_PARTITION=y
+CONFIG_ISO_PARTITION=y
# CONFIG_NET is not set
CONFIG_CLK=y
+CONFIG_CLK_QCOM_QCM2290=y
CONFIG_CLK_QCOM_QCS404=y
CONFIG_CLK_QCOM_SDM845=y
+CONFIG_CLK_QCOM_SM6115=y
+CONFIG_CLK_QCOM_SM8250=y
CONFIG_MSM_GPIO=y
CONFIG_QCOM_PMIC_GPIO=y
CONFIG_DM_KEYBOARD=y
CONFIG_BUTTON_KEYBOARD=y
+CONFIG_IOMMU=y
+CONFIG_ARM_SMMU=y
+CONFIG_MISC=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_MSM=y
CONFIG_PHY=y
+CONFIG_PHY_QCOM_QMP_UFS=y
+CONFIG_PHY_QCOM_QUSB2=y
+CONFIG_PHY_QCOM_USB_HS_7NM=y
CONFIG_PINCTRL=y
+CONFIG_PINCTRL_QCOM_QCM2290=y
CONFIG_PINCTRL_QCOM_QCS404=y
CONFIG_PINCTRL_QCOM_SDM845=y
+CONFIG_PINCTRL_QCOM_SM6115=y
+CONFIG_PINCTRL_QCOM_SM8250=y
CONFIG_DM_PMIC=y
CONFIG_PMIC_QCOM=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_EMULATION=y
CONFIG_SCSI=y
CONFIG_DM_SCSI=y
CONFIG_MSM_GENI_SERIAL=y
@@ -58,38 +78,16 @@
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_DWC3=y
CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
CONFIG_USB_STORAGE=y
CONFIG_UFS=y
+CONFIG_QCOM_UFS=y
CONFIG_VIDEO=y
# CONFIG_VIDEO_FONT_8X16 is not set
CONFIG_VIDEO_FONT_16X32=y
CONFIG_SYS_WHITE_ON_BLACK=y
CONFIG_NO_FB_CLEAR=y
CONFIG_VIDEO_SIMPLE=y
-CONFIG_HEXDUMP=y
-# CONFIG_GENERATE_SMBIOS_TABLE is not set
+# CONFIG_SMBIOS is not set
+CONFIG_EFI_SET_TIME=y
CONFIG_LMB_MAX_REGIONS=64
-
-CONFIG_BAUDRATE=115200
-
-# Uncomment to enable UART pre-relocation
-CONFIG_DEBUG_UART=y
-CONFIG_DEBUG_UART_ANNOUNCE=y
-# This is the address of the debug-uart peripheral
-# The value here is for SDM845, other platforms will vary
-CONFIG_DEBUG_UART_BASE=0xa84000
-# Boards older than ~2018 pre-date the GENI driver and unfortunately
-# aren't supported here
-CONFIG_DEBUG_UART_MSM_GENI=y
-# For sdm845 this is the UART clock rate
-CONFIG_DEBUG_UART_CLOCK=7372800
-# Most newer boards have an oversampling value of 16 instead
-# of 32, they need the clock rate to be doubled
-#CONFIG_DEBUG_UART_CLOCK=14745600
-
-CONFIG_LOG=y
-CONFIG_HEXDUMP=y
-CONFIG_CMD_LOG=y
-CONFIG_LOG_MAX_LEVEL=9
-CONFIG_LOG_DEFAULT_LEVEL=9
-CONFIG_LOGLEVEL=9