| Motorola MPC8540ADS and MPC8560ADS board |
| |
| Xianghua Xiao(X.Xiao@motorola.com) |
| Created 10/15/03 |
| ----------------------------------------- |
| |
| 0. Toolchain |
| The Binutils in current ELDK toolchain will not support MPC85xx chip. You need |
| use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils. |
| |
| 1. SWITCH SETTINGS & JUMPERS |
| 1.1 First, make sure the board default setting is consistent with the document |
| shipped with your board. Then apply the following changes: |
| SW3[1-6]="all OFF" (boot from 32bit flash, no boot sequence is used) |
| SW10[2-6]="all OFF" (turn on CPM SCC for serial port,works for 8540/8560) |
| SW11[2]='OFF for 8560, ON for 8540' (single switch to toggle 8540.8560 mode) |
| SW11[7]='ON' (rev2), 'OFF' (rev1) |
| SW4[7-8]="OFF OFF" (enable serial ports,I'm using the top serial connector) |
| SW22[1-4]="OFF OFF ON OFF" |
| SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF" |
| J1 = "Enable Prog" (Make sure your flash is programmable for development) |
| 1.2 If you want to test PCI functionality with a 33Mhz PCI card, you will |
| have to change the system clock from the default 66Mhz to 33Mhz by |
| setting SW15[1]="OFF" and SW17[8]="OFF". After that you may also need |
| double your platform clock(SW6) because the system clock is now only |
| half of its original value. |
| 1.3 SW6 is a very important switch, it decides your platform clock and CPU |
| clock based on the on-board system clock(default 66MHz). Check the |
| document along with your board for details. |
| |
| |
| 2. MEMORY MAP TO WORK WITH LINUX KERNEL |
| |
| 2.1. For the initial bringup, we adopted a consistent memory scheme |
| between u-boot and linux kernel, you can customize it based on your |
| system requirements: |
| |
| 0x0000_0000 0x7fff_ffff DDR 2G |
| 0x8000_0000 0x9fff_ffff PCI MEM 512M |
| 0xc000_0000 0xdfff_ffff Rapid IO 512M |
| 0xe000_0000 0xe000_ffff CCSR 1M |
| 0xe200_0000 0xe2ff_ffff PCI IO 16M |
| 0xf000_0000 0xf7ff_ffff SDRAM 128M |
| 0xf800_0000 0xf80f_ffff BCSR 1M |
| 0xff00_0000 0xffff_ffff FLASH (boot bank) 16M |
| |
| 2.2 We are submitting Linux kernel patches for MPC8540 and MPC8560. You |
| can download them from linuxppc-2.4 public source. Please make sure the |
| kernel's ppcboot.h is consistent with U-Boot's u-boot.h. You can use two |
| default configuration files as your starting points to configure the |
| kernel: |
| arch/ppc/configs/mpc8540_ads_defconfig |
| arch/ppc/configs/mpc8560_ads_defconfig |
| |
| 3. DEFINITIONS AND COMPILATION |
| 3.1 Explanation on NEW definitions in include/configs/MPC8540ADS.h and include/ |
| configs/MPC8560ADS.h |
| CONFIG_BOOKE BOOKE(e.g. Motorola MPC85xx, IBM 440, etc) |
| CONFIG_E500 BOOKE e500 family(Motorola) |
| CONFIG_MPC85xx MPC8540,MPC8560 and their derivatives |
| CONFIG_MPC8540 MPC8540 specific |
| CONFIG_MPC8560 MPC8560 specific |
| CONFIG_MPC8540ADS MPC8540ADS board specific |
| CONFIG_MPC8560ADS MPC8560ADS board specific |
| CONFIG_TSEC_ENET Use on-chip 10/100/1000 ethernet for networking |
| CONFIG_SPD_EEPROM Use SPD EEPROM for DDR auto configuration, you can also |
| manual config the DDR after undef this definition. |
| CONFIG_DDR_ECC only for ECC DDR module |
| CONFIG_DDR_DLL DLL fix on some ADS boards needed for more stability. |
| CONFIG_RAM_AS_FLASH after define this, you can load U-Boot into localbus |
| SDRAM and treat localbus SDRAM as a flash. We use this |
| memory based U-Boot before flash is working while Metrowerks |
| and Windriver are still working on their flash/JTAG tools. |
| if you can program the flash directly, undef this. |
| Other than the above definitions, the rest in the config files are straightforward. |
| |
| |
| 3.2 Compilation |
| export CROSS_COMPILE=your-cross-compile-prefix(assuming you're using BASH shell) |
| cd u-boot |
| make distclean |
| make MPC8560ADS_config (or make MPC8540ADS_config) |
| make |
| |
| 4. Notes: |
| 4.1 When connecting with kermit, the following commands must be present.in |
| your .kermrc file. These are especially important when booting as |
| MPC8560, as the serial console will not work without them: |
| |
| set speed 115200 |
| set carrier-watch off |
| set handshake none |
| set flow-control none |
| robust |
| |
| |
| 4.2 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC ethernet. If that |
| happens, you can try the following steps to make network work: |
| MPC8560ADS>tftp 1000000 pImage |
| (if it hangs, use Ctrl-C to quit) |
| MPC8560ADS>nm fdf24524 |
| >0 |
| >1 |
| >. (to quit this memory operation) |
| MPC8560ADS>tftp 1000000 pImage |
| 4.3 If you're one of the early developers using the Rev1 8540/8560 chips, please use U-Boot |
| 1.0.0, as the newer silicon will only support Rev2 and future revisions of 8540/8560. |
| |
| |
| 4.4 Reflash U-boot Image using U-boot |
| |
| => tftp 0 u-boot.bin |
| => protect off fff80000 ffffffff |
| => erase fff80000 ffffffff |
| => cp.b 0 fff80000 80000 |
| |
| |
| 5. Screen dump: |
| 5.1 MPC8540ADS board |
| U-Boot 1.0.0-pre (Oct 15 2003 - 13:40:33) |
| |
| Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200010 |
| Board: Motorola MPC8540ADS Board |
| CPU: 792 MHz |
| CCB: 264 MHz |
| DDR: 132 MHz |
| LBC: 66 MHz |
| L1 D-cache 32KB, L1 I-cache 32KB enabled. |
| I2C: ready |
| DRAM: DDR module detected, total size:128MB. |
| 128 MB |
| FLASH: 16 MB |
| L2 cache enabled: 256KB |
| *** Warning - bad CRC, using default environment |
| |
| In: serial |
| Out: serial |
| Err: serial |
| Net: MOTOROLA ETHERNE |
| Hit any key to stop autoboot: 0 |
| MPC8540ADS=> fli |
| |
| Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K) |
| Size: 16 MB in 64 Sectors |
| Sector Start Addresses: |
| FF000000 FF040000 FF080000 FF0C0000 FF100000 |
| FF140000 FF180000 FF1C0000 FF200000 FF240000 |
| FF280000 FF2C0000 FF300000 FF340000 FF380000 |
| FF3C0000 FF400000 FF440000 FF480000 FF4C0000 |
| FF500000 FF540000 FF580000 FF5C0000 FF600000 |
| FF640000 FF680000 FF6C0000 FF700000 FF740000 |
| FF780000 FF7C0000 FF800000 FF840000 FF880000 |
| FF8C0000 FF900000 FF940000 FF980000 FF9C0000 |
| FFA00000 FFA40000 FFA80000 FFAC0000 FFB00000 |
| FFB40000 FFB80000 FFBC0000 FFC00000 FFC40000 |
| FFC80000 FFCC0000 FFD00000 FFD40000 FFD80000 |
| FFDC0000 FFE00000 FFE40000 FFE80000 FFEC0000 |
| FFF00000 FFF40000 FFF80000 (RO) FFFC0000 (RO) |
| MPC8540ADS=> imi ff000000 |
| |
| ## Checking Image at ff000000 ... |
| Image Name: Linux-2.4.21-rc5 |
| Image Type: PowerPC Linux Kernel Image (gzip compressed) |
| Data Size: 800594 Bytes = 781.8 kB |
| Load Address: 00000000 |
| Entry Point: 00000000 |
| Verifying Checksum ... OK |
| MPC8540ADS=> bdinfo |
| memstart = 0x00000000 |
| memsize = 0x08000000 |
| flashstart = 0xFF000000 |
| flashsize = 0x01000000 |
| flashoffset = 0x00000000 |
| sramstart = 0x00000000 |
| sramsize = 0x00000000 |
| immr_base = 0xFDF00000 |
| bootflags = 0x40003F80 |
| intfreq = 792 MHz |
| busfreq = 264 MHz |
| ethaddr = 00:01:AF:07:9B:8A |
| eth1addr = 00:01:AF:07:9B:8B |
| eth2addr = 00:01:AF:07:9B:8C |
| IP addr = 10.82.0.105 |
| baudrate = 115200 bps |
| MPC8540ADS=> printenv |
| bootargs=root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200 |
| bootcmd=bootm 0xff300000 0xff700000 |
| bootdelay=3 |
| baudrate=115200 |
| loads_echo=1 |
| ethaddr=00:01:af:07:9b:8a |
| eth1addr=00:01:af:07:9b:8b |
| eth2addr=00:01:af:07:9b:8c |
| ipaddr=10.82.0.105 |
| serverip=163.12.64.52 |
| rootpath=/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx |
| gatewayip=10.82.1.254 |
| netmask=255.255.254.0 |
| hostname=MPC8560ADS_PILOT_003 |
| bootfile=pImage |
| stdin=serial |
| stdout=serial |
| stderr=serial |
| |
| Environment size: 560/8188 bytes |
| MPC8540ADS=> bootm ff000000 |
| ## Booting image at ff000000 ... |
| Image Name: Linux-2.4.21-rc5 |
| Image Type: PowerPC Linux Kernel Image (gzip compressed) |
| Data Size: 800594 Bytes = 781.8 kB |
| Load Address: 00000000 |
| Entry Point: 00000000 |
| Verifying Checksum ... OK |
| Uncompressing Kernel Image ... OK |
| mpc85xx_init(): exit |
| id mach(): done |
| MMU:enter |
| Memory CAM mapping: CAM0=64Mb, CAM1=64Mb, CAM2=0Mb residual: 0Mb |
| MMU:hw init |
| MMU:mapin |
| MMU:mapin_ram done |
| MMU:setio |
| MMU:exit |
| Linux version 2.4.21-rc5 (@etest) (gcc version 2.95.3 20010315 (release)) #1 Wed Oct 15 09:05:42 CDT 2003 |
| setup_arch: enter |
| setup_arch: bootmem |
| mpc85xx_setup_arch |
| Host Bridge Vendor ID = 1057 |
| Host Bridge Device ID = 3 |
| Host Bridge header = 0 |
| arch: exit |
| On node 0 totalpages: 32768 |
| zone(0): 32768 pages. |
| zone(1): 0 pages. |
| zone(2): 0 pages. |
| Kernel command line: root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8540ads-003:eth0:off console=ttyS0,115200 |
| openpic: enter |
| OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf40000 |
| openpic: timer |
| openpic: external |
| openpic: spurious |
| openpic: exit |
| time_init: decrementer frequency = 33.000000 MHz |
| Calibrating delay loop... 226.09 BogoMIPS |
| Memory: 127488k available (1344k kernel code, 448k data, 248k init, 0k highmem) |
| Dentry cache hash table entries: 16384 (order: 5, 131072 bytes) |
| Inode cache hash table entries: 8192 (order: 4, 65536 bytes) |
| Mount cache hash table entries: 512 (order: 0, 4096 bytes) |
| Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes) |
| Page-cache hash table entries: 32768 (order: 5, 131072 bytes) |
| POSIX conformance testing by UNIFIX |
| PCI: Probing PCI hardware |
| |
| Linux NET4.0 for Linux 2.4 |
| Based upon Swansea University Computer Society NET3.039 |
| Initializing RT netlink socket |
| Starting kswapd |
| Installing knfsd (copyright (C) 1996 okir@monad.swb.de). |
| pty: 256 Unix98 ptys configured |
| Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled |
| ttyS00 at 0xfdf04500 (irq = 90) is a 16550A |
| ttyS01 at 0xfdf04600 (irq = 0) is a 16550A |
| eth0: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8a: |
| eth1: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8b: |
| RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize |
| loop: loaded (max 8 devices) |
| Intel(R) PRO/1000 Network Driver - version 5.0.43-k1 |
| Copyright (c) 1999-2003 Intel Corporation. |
| PPP generic driver version 2.4.2 |
| PPP Deflate Compression module registered |
| NET4: Linux TCP/IP 1.0 for NET4.0 |
| IP Protocols: ICMP, UDP, TCP, IGMP |
| IP: routing cache hash table of 1024 buckets, 8Kbytes |
| TCP: Hash tables configured (established 8192 bind 8192) |
| IP-Config: Complete: |
| device=eth0, addr=10.82.0.105, mask=255.255.254.0, gw=10.82.1.254, |
| host=mpc8540ads-003, domain=, nis-domain=(none), |
| bootserver=163.12.64.52, rootserver=163.12.64.52, rootpath= |
| NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. |
| Looking up port of RPC 100003/2 on 163.12.64.52 |
| Looking up port of RPC 100005/1 on 163.12.64.52 |
| VFS: Mounted root (nfs filesystem). |
| Freeing unused kernel memory: 248k init |
| INIT: version 2.78 booting |
| Activating swap... |
| Checking all file systems... |
| Parallelizing fsck version 1.22 (22-Jun-2001) |
| Mounting local filesystems... |
| nothing was mounted |
| Cleaning: /etc/network/ifstate. |
| Setting up IP spoofing protection: rp_filter. |
| Disable TCP/IP Explicit Congestion Notification: done. |
| Configuring network interfaces: done. |
| Starting portmap daemon: portmap. |
| Cleaning: /tmp /var/lock /var/run. |
| INIT: Entering runlevel: 2 |
| Starting system log daemon: syslogd klogd. |
| Starting internet superserver: inetd. |
| |
| mpc8540ads-003 login: root |
| Last login: Thu Jan 1 00:00:07 1970 on console |
| Linux mpc8540ads-003 2.4.21-rc5 #1 Wed Oct 15 09:05:42 CDT 2003 ppc unknown |
| |
| root@mpc8540ads-003:~# ls |
| 21142.o aa e100.o hello.o mii.o timer.o |
| root@mpc8540ads-003:~# /sbin/ifconfig |
| eth0 Link encap:Ethernet HWaddr 00:01:AF:07:9B:8A |
| inet addr:10.82.0.105 Bcast:10.82.1.255 Mask:255.255.254.0 |
| UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 |
| RX packets:4576 errors:0 dropped:0 overruns:0 frame:0 |
| TX packets:2587 errors:0 dropped:0 overruns:0 carrier:0 |
| collisions:0 txqueuelen:100 |
| RX bytes:4457023 (4.2 Mb) TX bytes:437770 (427.5 Kb) |
| Base address:0x4000 |
| |
| lo Link encap:Local Loopback |
| inet addr:127.0.0.1 Mask:255.0.0.0 |
| UP LOOPBACK RUNNING MTU:16436 Metric:1 |
| RX packets:4 errors:0 dropped:0 overruns:0 frame:0 |
| TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 |
| collisions:0 txqueuelen:0 |
| RX bytes:296 (296.0 b) TX bytes:296 (296.0 b) |
| |
| root@mpc8540ads-003:~# ping 163.12.64.52 |
| PING 163.12.64.52 (163.12.64.52): 56 data bytes |
| 64 bytes from 163.12.64.52: icmp_seq=0 ttl=63 time=0.2 ms |
| 64 bytes from 163.12.64.52: icmp_seq=1 ttl=63 time=0.1 ms |
| 64 bytes from 163.12.64.52: icmp_seq=2 ttl=63 time=0.1 ms |
| |
| --- 163.12.64.52 ping statistics --- |
| 3 packets transmitted, 3 packets received, 0% packet loss |
| round-trip min/avg/max = 0.1/0.1/0.2 ms |
| root@mpc8540ads-003:~# |
| |
| 5.2 MPC8560ADS board |
| U-Boot 1.0.0-pre (Oct 15 2003 - 13:42:04) |
| |
| Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200010 |
| Board: Motorola MPC8560ADS Board |
| CPU: 792 MHz |
| CCB: 264 MHz |
| DDR: 132 MHz |
| LBC: 66 MHz |
| CPM: 264 Mhz |
| L1 D-cache 32KB, L1 I-cache 32KB enabled. |
| I2C: ready |
| DRAM: DDR module detected, total size:128MB. |
| 128 MB |
| FLASH: 16 MB |
| L2 cache enabled: 256KB |
| *** Warning - bad CRC, using default environment |
| |
| In: serial |
| Out: serial |
| Err: serial |
| Net: MOTOROLA ETHERNE |
| Hit any key to stop autoboot: 3 |
| MPC8560ADS=> bdinfo |
| memstart = 0x00000000 |
| memsize = 0x08000000 |
| flashstart = 0xFF000000 |
| flashsize = 0x01000000 |
| flashoffset = 0x00000000 |
| sramstart = 0x00000000 |
| sramsize = 0x00000000 |
| immr_base = 0xFDF00000 |
| bootflags = 0x00000000 |
| vco = 528 MHz |
| sccfreq = 132 MHz |
| brgfreq = 132 MHz |
| intfreq = 792 MHz |
| cpmfreq = 264 MHz |
| busfreq = 264 MHz |
| ethaddr = 00:01:AF:07:9B:8A |
| eth1addr = 00:01:AF:07:9B:8B |
| eth2addr = 00:01:AF:07:9B:8C |
| IP addr = 10.82.0.105 |
| baudrate = 115200 bps |
| MPC8560ADS=> printenv |
| bootargs=root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200 |
| bootcmd=bootm 0xff400000 0xff700000 |
| bootdelay=3 |
| baudrate=115200 |
| loads_echo=1 |
| ethaddr=00:01:af:07:9b:8a |
| eth1addr=00:01:af:07:9b:8b |
| eth2addr=00:01:af:07:9b:8c |
| ipaddr=10.82.0.105 |
| serverip=163.12.64.52 |
| rootpath=/home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx |
| gatewayip=10.82.1.254 |
| netmask=255.255.254.0 |
| hostname=MPC8560ADS_PILOT_003 |
| bootfile=pImage |
| stdin=serial |
| stdout=serial |
| stderr=serial |
| |
| Environment size: 560/8188 bytes |
| MPC8560ADS=> fli |
| |
| Bank # 1: Intel 28F640J3A (64 Mbit, 64 x 128K) |
| Size: 16 MB in 64 Sectors |
| Sector Start Addresses: |
| FF000000 FF040000 FF080000 FF0C0000 FF100000 |
| FF140000 FF180000 FF1C0000 FF200000 FF240000 |
| FF280000 FF2C0000 FF300000 FF340000 FF380000 |
| FF3C0000 FF400000 FF440000 FF480000 FF4C0000 |
| FF500000 FF540000 FF580000 FF5C0000 FF600000 |
| FF640000 FF680000 FF6C0000 FF700000 FF740000 |
| FF780000 FF7C0000 FF800000 FF840000 FF880000 |
| FF8C0000 FF900000 FF940000 FF980000 FF9C0000 |
| FFA00000 FFA40000 FFA80000 FFAC0000 FFB00000 |
| FFB40000 FFB80000 FFBC0000 FFC00000 FFC40000 |
| FFC80000 FFCC0000 FFD00000 FFD40000 FFD80000 |
| FFDC0000 FFE00000 FFE40000 FFE80000 FFEC0000 |
| FFF00000 FFF40000 FFF80000 (RO) FFFC0000 (RO) |
| MPC8560ADS=> imi ff100000 |
| |
| ## Checking Image at ff100000 ... |
| Image Name: Linux-2.4.21-rc5 |
| Image Type: PowerPC Linux Kernel Image (gzip compressed) |
| Data Size: 755361 Bytes = 737.7 kB |
| Load Address: 00000000 |
| Entry Point: 00000000 |
| Verifying Checksum ... OK |
| MPC8560ADS=> tftp 1000000 pImage.dracom.public |
| TFTP from server 163.12.64.52; our IP address is 10.82.0.105; sending through gateway 10.82.1.254 |
| Filename 'pImage.dracom.public'. |
| Load address: 0x1000000 |
| Loading: *################################################################# |
| ################################################################# |
| ################## |
| done |
| Bytes transferred = 755425 (b86e1 hex) |
| MPC8560ADS=> bootm ff100000 |
| ## Booting image at ff100000 ... |
| Image Name: Linux-2.4.21-rc5 |
| Image Type: PowerPC Linux Kernel Image (gzip compressed) |
| Data Size: 755361 Bytes = 737.7 kB |
| Load Address: 00000000 |
| Entry Point: 00000000 |
| Verifying Checksum ... OK |
| Uncompressing Kernel Image ... OK |
| mpc85xx_init(): exit |
| id mach(): done |
| MMU:enter |
| Memory CAM mapping: CAM0=64Mb, CAM1=64Mb, CAM2=0Mb residual: 0Mb |
| MMU:hw init |
| MMU:mapin |
| MMU:mapin_ram done |
| MMU:setio |
| MMU:exit |
| Linux version 2.4.21-rc5 (@etest) (gcc version 2.95.3 20010315 (release)) #2 Wed Oct 15 09:13:46 CDT 2003 |
| setup_arch: enter |
| setup_arch: bootmem |
| mpc85xx_setup_arch |
| Host Bridge Vendor ID = 1057 |
| Host Bridge Device ID = 3 |
| Host Bridge header = 0 |
| arch: exit |
| On node 0 totalpages: 32768 |
| zone(0): 32768 pages. |
| zone(1): 0 pages. |
| zone(2): 0 pages. |
| Kernel command line: root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200 |
| openpic: enter |
| OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fdf40000 |
| openpic: timer |
| openpic: external |
| openpic: spurious |
| openpic: exit |
| time_init: decrementer frequency = 33.000000 MHz |
| Calibrating delay loop... 226.09 BogoMIPS |
| Memory: 127624k available (1276k kernel code, 384k data, 236k init, 0k highmem) |
| Dentry cache hash table entries: 16384 (order: 5, 131072 bytes) |
| Inode cache hash table entries: 8192 (order: 4, 65536 bytes) |
| Mount cache hash table entries: 512 (order: 0, 4096 bytes) |
| Buffer-cache hash table entries: 8192 (order: 3, 32768 bytes) |
| Page-cache hash table entries: 32768 (order: 5, 131072 bytes) |
| POSIX conformance testing by UNIFIX |
| PCI: Probing PCI hardware |
| |
| Linux NET4.0 for Linux 2.4 |
| Based upon Swansea University Computer Society NET3.039 |
| Initializing RT netlink socket |
| Starting kswapd |
| Installing knfsd (copyright (C) 1996 okir@monad.swb.de). |
| CPM UART driver version 0.01 |
| ttyS0 on SCC1 at 0x8000, BRG1 |
| UART interrupt installed(40) |
| pty: 256 Unix98 ptys configured |
| eth0: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8a: |
| eth1: Three Speed Ethernet Controller Version 0.2, 00:01:af:07:9b:8b: |
| RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize |
| loop: loaded (max 8 devices) |
| Intel(R) PRO/1000 Network Driver - version 5.0.43-k1 |
| Copyright (c) 1999-2003 Intel Corporation. |
| PPP generic driver version 2.4.2 |
| PPP Deflate Compression module registered |
| NET4: Linux TCP/IP 1.0 for NET4.0 |
| IP Protocols: ICMP, UDP, TCP, IGMP |
| IP: routing cache hash table of 1024 buckets, 8Kbytes |
| TCP: Hash tables configured (established 8192 bind 8192) |
| IP-Config: Complete: |
| device=eth0, addr=10.82.0.105, mask=255.255.254.0, gw=10.82.1.254, |
| host=mpc8560ads-003, domain=, nis-domain=(none), |
| bootserver=163.12.64.52, rootserver=163.12.64.52, rootpath= |
| NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. |
| Looking up port of RPC 100003/2 on 163.12.64.52 |
| Looking up port of RPC 100005/1 on 163.12.64.52 |
| VFS: Mounted root (nfs filesystem). |
| Freeing unused kernel memory: 236k init |
| INIT: version 2.78 booting |
| Activating swap... |
| Checking all file systems... |
| Parallelizing fsck version 1.22 (22-Jun-2001) |
| Mounting local filesystems... |
| nothing was mounted |
| Cleaning: /etc/network/ifstate. |
| Setting up IP spoofing protection: FAILED |
| Configuring network interfaces: done. |
| Starting portmap daemon: portmap. |
| Cleaning: /tmp /var/lock /var/run. |
| INIT: Entering runlevel: 2 |
| Starting system log daemon: syslogd klogd. |
| Starting internet superserver: inetd. |
| |
| mpc8560ads-003 login: root |
| Last login: Thu Jan 1 00:00:05 1970 on console |
| Linux mpc8560ads-003 2.4.21-rc5 #2 Wed Oct 15 09:13:46 CDT 2003 ppc unknown |
| |
| root@mpc8560ads-003:~# ls |
| 21142.o aa e100.o hello.o mii.o timer.o |
| root@mpc8560ads-003:~# cd / |
| root@mpc8560ads-003:/# ls |
| bin boot dev etc home lib mnt opt proc root sbin tmp usr var |
| root@mpc8560ads-003:/# /sbin/ifconfig |
| eth0 Link encap:Ethernet HWaddr 00:01:AF:07:9B:8A |
| inet addr:10.82.0.105 Bcast:10.82.1.255 Mask:255.255.254.0 |
| UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 |
| RX packets:4608 errors:0 dropped:0 overruns:0 frame:0 |
| TX packets:2610 errors:0 dropped:0 overruns:0 carrier:0 |
| collisions:0 txqueuelen:100 |
| RX bytes:4465943 (4.2 Mb) TX bytes:440944 (430.6 Kb) |
| Base address:0x4000 |
| |
| lo Link encap:Local Loopback |
| inet addr:127.0.0.1 Mask:255.0.0.0 |
| UP LOOPBACK RUNNING MTU:16436 Metric:1 |
| RX packets:4 errors:0 dropped:0 overruns:0 frame:0 |
| TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 |
| collisions:0 txqueuelen:0 |
| RX bytes:296 (296.0 b) TX bytes:296 (296.0 b) |
| |
| root@mpc8560ads-003:/# ping 163.12.64.52 |
| PING 163.12.64.52 (163.12.64.52): 56 data bytes |
| 64 bytes from 163.12.64.52: icmp_seq=0 ttl=63 time=0.1 ms |
| 64 bytes from 163.12.64.52: icmp_seq=1 ttl=63 time=0.1 ms |
| 64 bytes from 163.12.64.52: icmp_seq=2 ttl=63 time=0.1 ms |
| |
| --- 163.12.64.52 ping statistics --- |
| 3 packets transmitted, 3 packets received, 0% packet loss |
| round-trip min/avg/max = 0.1/0.1/0.1 ms |
| root@mpc8560ads-003:/# |