blob: 02e14609bb776cdf89d38d8f9753c19e140b30a4 [file] [log] [blame]
STMicroelectronics STM32MP1 clock tree initialization
=====================================================
The STM32MP1 clock tree initialization is based on device tree information
for RCC IP node (st,stm32mp1-rcc) and on fixed-clock nodes.
RCC IP = st,stm32mp1-rcc
========================
The RCC IP is both a reset and a clock controller but this documentation only
describes the fields added for clock tree initialization which are not present
in Linux binding for compatible "st,stm32mp1-rcc" defined in st,stm32mp1-rcc.txt
file.
The added properties for clock tree initialization are:
Required properties:
- st,clksrc : The clock sources configuration array in a platform specific
order.
For the STM32MP15x family there are 9 clock sources selector which are
configured in the following order:
MPU AXI MCU PLL12 PLL3 PLL4 RTC MCO1 MCO2
Clock source configuration values are defined by macros CLK_<NAME>_<SOURCE>
from dt-bindings/clock/stm32mp1-clksrc.h.
Example:
st,clksrc = <
CLK_MPU_PLL1P
CLK_AXI_PLL2P
CLK_MCU_PLL3P
CLK_PLL12_HSE
CLK_PLL3_HSE
CLK_PLL4_HSE
CLK_RTC_LSE
CLK_MCO1_DISABLED
CLK_MCO2_DISABLED
>;
- st,clkdiv : The clock main dividers value specified in an array
in a platform specific order.
When used, it shall describe the whole clock dividers tree.
For the STM32MP15x family there are 11 dividers values expected.
They shall be configured in the following order:
MPU AXI MCU APB1 APB2 APB3 APB4 APB5 RTC MCO1 MCO2
The each divider value uses the DIV coding defined in RCC associated
register RCC_xxxDIVR. In most the case, it is:
0x0: not divided
0x1: division by 2
0x2: division by 4
0x3: division by 8
...
Note that for RTC MCO1 MCO2, the coding is different:
0x0: not divided
0x1: division by 2
0x2: division by 3
0x3: division by 4
...
Example:
st,clkdiv = <
1 /*MPU*/
0 /*AXI*/
0 /*MCU*/
1 /*APB1*/
1 /*APB2*/
1 /*APB3*/
1 /*APB4*/
2 /*APB5*/
23 /*RTC*/
0 /*MCO1*/
0 /*MCO2*/
>;
Optional Properties:
- st,pll : A specific PLL configuration, including frequency.
PLL children nodes for PLL1 to PLL4 (see ref manual for details)
are listed with associated index 0 to 3 (st,pll@0 to st,pll@3).
PLLx is off when the associated node is absent.
Here are the available properties for each PLL node:
- cfg: The parameters for PLL configuration in the following order:
DIVM DIVN DIVP DIVQ DIVR Output.
DIVx values are defined as in RCC spec:
0x0: bypass (division by 1)
0x1: division by 2
0x2: division by 3
0x3: division by 4
...
Output contains a bitfield for each output value (1:ON/0:OFF)
BIT(0) => output P : DIVPEN
BIT(1) => output Q : DIVQEN
BIT(2) => output R : DIVREN
NB: macro PQR(p,q,r) can be used to build this value
with p,q,r = 0 or 1.
- frac : Fractional part of the multiplication factor
(optional, PLL is in integer mode when absent).
- csg : Clock Spreading Generator (optional) with parameters in the
following order: MOD_PER INC_STEP SSCG_MODE.
MOD_PER: Modulation Period Adjustment
INC_STEP: Modulation Depth Adjustment
SSCG_MODE: Spread spectrum clock generator mode, with associated
defined from stm32mp1-clksrc.h:
- SSCG_MODE_CENTER_SPREAD = 0
- SSCG_MODE_DOWN_SPREAD = 1
Example:
st,pll@0 {
cfg = < 1 53 0 0 0 1 >;
frac = < 0x810 >;
};
st,pll@1 {
cfg = < 1 43 1 0 0 PQR(0,1,1) >;
csg = < 10 20 1 >;
};
st,pll@2 {
cfg = < 2 85 3 13 3 0 >;
csg = < 10 20 SSCG_MODE_CENTER_SPREAD >;
};
st,pll@3 {
cfg = < 2 78 4 7 9 3 >;
};
- st,pkcs : used to configure the peripherals kernel clock selection.
The property is a list of peripheral kernel clock source identifiers defined
by macros CLK_<KERNEL-CLOCK>_<PARENT-CLOCK> as defined by header file
dt-bindings/clock/stm32mp1-clksrc.h.
st,pkcs may not list all the kernel clocks and has no ordering requirements.
Example:
st,pkcs = <
CLK_STGEN_HSE
CLK_CKPER_HSI
CLK_USBPHY_PLL2P
CLK_DSI_PLL2Q
CLK_I2C46_HSI
CLK_UART1_HSI
CLK_UART24_HSI
>;
other clocks = fixed-clock
==========================
The clock tree is also based on 5 fixed-clock in clocks node
used to define the state of associated ST32MP1 oscillators:
- clk-lsi
- clk-lse
- clk-hsi
- clk-hse
- clk-csi
At boot the clock tree initialization will
- enable oscillators present in device tree
- disable HSI oscillator if the node is absent (always activated by bootrom)
Optional properties :
a) for external oscillator: "clk-lse", "clk-hse"
4 optional fields are managed
- "st,bypass" configures the oscillator bypass mode (HSEBYP, LSEBYP)
- "st,digbypass" configures the bypass mode as full-swing digital
signal (DIGBYP)
- "st,css" activates the clock security system (HSECSSON, LSECSSON)
- "st,drive" (only for LSE) contains the value of the drive for the
oscillator (see LSEDRV_ defined in the file
dt-bindings/clock/stm32mp1-clksrc.h)
Example board file:
/ {
clocks {
clk_hse: clk-hse {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <64000000>;
st,bypass;
};
clk_lse: clk-lse {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
st,css;
st,drive = <LSEDRV_LOWEST>;
};
};
b) for internal oscillator: "clk-hsi"
Internally HSI clock is fixed to 64MHz for STM32MP157 SoC.
In device tree, clk-hsi is the clock after HSIDIV (clk_hsi in RCC
doc). So this clock frequency is used to compute the expected HSI_DIV
for the clock tree initialization.
Example with HSIDIV = /1:
/ {
clocks {
clk_hsi: clk-hsi {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <64000000>;
};
};
Example with HSIDIV = /2
/ {
clocks {
clk_hsi: clk-hsi {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32000000>;
};
};
Example of clock tree initialization
====================================
/ {
clocks {
u-boot,dm-pre-reloc;
clk_hse: clk-hse {
u-boot,dm-pre-reloc;
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
st,digbypass;
};
clk_hsi: clk-hsi {
u-boot,dm-pre-reloc;
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <64000000>;
};
clk_lse: clk-lse {
u-boot,dm-pre-reloc;
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
};
clk_lsi: clk-lsi {
u-boot,dm-pre-reloc;
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32000>;
};
clk_csi: clk-csi {
u-boot,dm-pre-reloc;
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <4000000>;
};
};
soc {
rcc: rcc@50000000 {
u-boot,dm-pre-reloc;
compatible = "st,stm32mp1-rcc", "syscon";
reg = <0x50000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
st,clksrc = <
CLK_MPU_PLL1P
CLK_AXI_PLL2P
CLK_MCU_PLL3P
CLK_PLL12_HSE
CLK_PLL3_HSE
CLK_PLL4_HSE
CLK_RTC_LSE
CLK_MCO1_DISABLED
CLK_MCO2_DISABLED
>;
st,clkdiv = <
1 /*MPU*/
0 /*AXI*/
0 /*MCU*/
1 /*APB1*/
1 /*APB2*/
1 /*APB3*/
1 /*APB4*/
2 /*APB5*/
23 /*RTC*/
0 /*MCO1*/
0 /*MCO2*/
>;
st,pkcs = <
CLK_CKPER_HSE
CLK_FMC_ACLK
CLK_QSPI_ACLK
CLK_ETH_DISABLED
CLK_SDMMC12_PLL4P
CLK_DSI_DSIPLL
CLK_STGEN_HSE
CLK_USBPHY_HSE
CLK_SPI2S1_PLL3Q
CLK_SPI2S23_PLL3Q
CLK_SPI45_HSI
CLK_SPI6_HSI
CLK_I2C46_HSI
CLK_SDMMC3_PLL4P
CLK_USBO_USBPHY
CLK_ADC_CKPER
CLK_CEC_LSE
CLK_I2C12_HSI
CLK_I2C35_HSI
CLK_UART1_HSI
CLK_UART24_HSI
CLK_UART35_HSI
CLK_UART6_HSI
CLK_UART78_HSI
CLK_SPDIF_PLL4P
CLK_FDCAN_PLL4Q
CLK_SAI1_PLL3Q
CLK_SAI2_PLL3Q
CLK_SAI3_PLL3Q
CLK_SAI4_PLL3Q
CLK_RNG1_LSI
CLK_RNG2_LSI
CLK_LPTIM1_PCLK1
CLK_LPTIM23_PCLK3
CLK_LPTIM45_LSE
>;
/* VCO = 1300.0 MHz => P = 650 (CPU) */
pll1: st,pll@0 {
cfg = < 2 80 0 0 0 PQR(1,0,0) >;
frac = < 0x800 >;
u-boot,dm-pre-reloc;
};
/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU),
R = 533 (DDR) */
pll2: st,pll@1 {
cfg = < 2 65 1 0 0 PQR(1,1,1) >;
frac = < 0x1400 >;
u-boot,dm-pre-reloc;
};
/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
pll3: st,pll@2 {
cfg = < 1 33 1 16 36 PQR(1,1,1) >;
frac = < 0x1a04 >;
u-boot,dm-pre-reloc;
};
/* VCO = 594.0 MHz => P = 99, Q = 74, R = 74 */
pll4: st,pll@3 {
cfg = < 3 98 5 7 7 PQR(1,1,1) >;
u-boot,dm-pre-reloc;
};
};
};
};