| .. SPDX-License-Identifier: GPL-2.0+ |
| |
| Verdin iMX8M Mini Module |
| ======================== |
| |
| Quick Start |
| ----------- |
| |
| - Build the ARM trusted firmware binary |
| - Get the DDR firmware |
| - Build U-Boot |
| - Flash to eMMC |
| - Boot |
| |
| Get and Build the ARM Trusted Firmware (Trusted Firmware A) |
| ----------------------------------------------------------- |
| |
| .. code-block:: bash |
| |
| $ echo "Downloading and building TF-A..." |
| $ git clone https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git |
| $ cd trusted-firmware-a |
| |
| Then build ATF (TF-A): |
| |
| .. code-block:: bash |
| |
| $ make PLAT=imx8mm IMX_BOOT_UART_BASE=0x30860000 bl31 |
| $ cp build/imx8mm/release/bl31.bin ../ |
| |
| Get the DDR Firmware |
| -------------------- |
| |
| .. code-block:: bash |
| |
| $ cd .. |
| $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.10.1.bin |
| $ chmod +x firmware-imx-8.10.1.bin |
| $ ./firmware-imx-8.10.1.bin |
| $ cp firmware-imx-8.10.1/firmware/ddr/synopsys/lpddr4*.bin ./ |
| |
| Build U-Boot |
| ------------ |
| .. code-block:: bash |
| |
| $ export CROSS_COMPILE=aarch64-linux-gnu- |
| $ export ATF_LOAD_ADDR=0x920000 |
| $ make verdin-imx8mm_defconfig |
| $ make |
| |
| Flash to eMMC |
| ------------- |
| |
| .. code-block:: bash |
| |
| > tftpboot ${loadaddr} flash.bin |
| > setexpr blkcnt ${filesize} + 0x1ff && setexpr blkcnt ${blkcnt} / 0x200 |
| > mmc dev 0 1 && mmc write ${loadaddr} 0x2 ${blkcnt} |
| |
| As a convenience, instead of the last two commands one may also use the update |
| U-Boot wrapper: |
| |
| .. code-block:: bash |
| |
| > run update_uboot |
| |
| Boot |
| ---- |
| |
| ATF, U-Boot proper and u-boot.dtb images are packed into FIT image, |
| which is loaded and parsed by SPL. |
| |
| Boot sequence is: |
| |
| * SPL ---> ATF (TF-A) ---> U-Boot proper |
| |
| Output: |
| |
| .. code-block:: bash |
| |
| U-Boot SPL 2021.10-rc2-00028-gee010ba1129 (Aug 23 2021 - 16:56:02 +0200) |
| Normal Boot |
| WDT: Started with servicing (60s timeout) |
| Trying to boot from MMC1 |
| NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b |
| NOTICE: BL31: Built : 18:02:12, Aug 16 2021 |
| |
| |
| U-Boot 2021.10-rc2-00028-gee010ba1129 (Aug 23 2021 - 16:56:02 +0200) |
| |
| CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz |
| Reset cause: POR |
| DRAM: 2 GiB |
| WDT: Started with servicing (60s timeout) |
| MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 |
| Loading Environment from MMC... OK |
| In: serial |
| Out: serial |
| Err: serial |
| Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.1A, Serial# 06760554 |
| Carrier: Toradex Verdin Development Board V1.1A, Serial# 10754333 |
| Setting variant to wifi |
| Net: eth0: ethernet@30be0000 |
| Hit any key to stop autoboot: 0 |
| Verdin iMX8MM # |