blob: f5e1b646ca2e52000e1f8dd5b175e92c75869028 [file] [log] [blame]
/*
* Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
* Hayden Fraser (Hayden.Fraser@freescale.com)
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
#ifndef _M5253EVBE_H
#define _M5253EVBE_H
#define CONFIG_MCF52x2 /* define processor family */
#define CONFIG_M5253 /* define processor type */
#define CONFIG_M5253EVBE /* define board type */
#define CONFIG_MCFTMR
#define CONFIG_MCFUART
#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 19200
#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
#undef CONFIG_WATCHDOG /* disable watchdog */
#define CONFIG_BOOTDELAY 5
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
*/
#ifndef CONFIG_MONITOR_IS_IN_RAM
#define CFG_ENV_OFFSET 0x4000
#define CFG_ENV_SECT_SIZE 0x2000
#define CFG_ENV_IS_IN_FLASH 1
#else
#define CFG_ENV_ADDR 0xffe04000
#define CFG_ENV_SECT_SIZE 0x2000
#define CFG_ENV_IS_IN_FLASH 1
#endif
/*
* BOOTP options
*/
#undef CONFIG_BOOTP_BOOTFILESIZE
#undef CONFIG_BOOTP_BOOTPATH
#undef CONFIG_BOOTP_GATEWAY
#undef CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_NET
#define CONFIG_CMD_LOADB
#define CONFIG_CMD_LOADS
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_IDE
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_MISC
/* ATA */
#define CONFIG_DOS_PARTITION
#define CONFIG_MAC_PARTITION
#define CONFIG_IDE_RESET 1
#define CONFIG_IDE_PREINIT 1
#define CONFIG_ATAPI
#undef CONFIG_LBA48
#define CFG_IDE_MAXBUS 1
#define CFG_IDE_MAXDEVICE 2
#define CFG_ATA_BASE_ADDR (CFG_MBAR2 + 0x800)
#define CFG_ATA_IDE0_OFFSET 0
#define CFG_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */
#define CFG_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */
#define CFG_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */
#define CFG_ATA_STRIDE 4 /* Interval between registers */
#define _IO_BASE 0
#define CFG_PROMPT "=> "
#define CFG_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
#define CFG_LOAD_ADDR 0x00100000
#define CFG_MEMTEST_START 0x400
#define CFG_MEMTEST_END 0x380000
#define CFG_HZ 1000
#undef CFG_PLL_BYPASS /* bypass PLL for test purpose */
#define CFG_FAST_CLK
#ifdef CFG_FAST_CLK
# define CFG_PLLCR 0x1243E054
# define CFG_CLK 140000000
#else
# define CFG_PLLCR 0x135a4140
# define CFG_CLK 70000000
#endif
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
#define CFG_MBAR 0x10000000 /* Register Base Addrs */
#define CFG_MBAR2 0x80000000 /* Module Base Addrs 2 */
/*
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR 0x20000000
#define CFG_INIT_RAM_END 0x10000 /* End of used area in internal SRAM */
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
#define CFG_SDRAM_BASE 0x00000000
#define CFG_SDRAM_SIZE 8 /* SDRAM size in MB */
#ifdef CONFIG_MONITOR_IS_IN_RAM
#define CFG_MONITOR_BASE 0x20000
#else
#define CFG_MONITOR_BASE (CFG_FLASH_BASE + 0x400)
#endif
#define CFG_MONITOR_LEN 0x40000
#define CFG_MALLOC_LEN (256 << 10)
#define CFG_BOOTPARAMS_LEN (64*1024)
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
#define CFG_BOOTMAPSZ (CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
/* FLASH organization */
#define CFG_FLASH_BASE 0xffe00000
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CFG_MAX_FLASH_SECT 35 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 1000
#define CFG_FLASH_CFI 1
#define CFG_FLASH_CFI_DRIVER 1
#define CFG_FLASH_SIZE 0x200000
#define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT
/* Cache Configuration */
#define CFG_CACHELINE_SIZE 16
/* Port configuration */
#define CFG_FECI2C 0xF0
#define CFG_CSAR0 0xFFE0
#define CFG_CSMR0 0x001F0021
#define CFG_CSCR0 0x1D80
#define CFG_CSAR1 0
#define CFG_CSMR1 0
#define CFG_CSCR1 0
#define CFG_CSAR2 0
#define CFG_CSMR2 0
#define CFG_CSCR2 0
#define CFG_CSAR3 0
#define CFG_CSMR3 0
#define CFG_CSCR3 0
/*-----------------------------------------------------------------------
* Port configuration
*/
#define CFG_GPIO_FUNC 0x00000008 /* Set gpio pins: none */
#define CFG_GPIO1_FUNC 0x00df00f0 /* 36-39(SWITCH),48-52(FPGAs),54 */
#define CFG_GPIO_EN 0x00000008 /* Set gpio output enable */
#define CFG_GPIO1_EN 0x00c70000 /* Set gpio output enable */
#define CFG_GPIO_OUT 0x00000008 /* Set outputs to default state */
#define CFG_GPIO1_OUT 0x00c70000 /* Set outputs to default state */
#define CFG_GPIO1_LED 0x00400000 /* user led */
#endif /* _M5253EVB_H */