| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * SH QSPI (Quad SPI) driver |
| * |
| * Copyright (C) 2013 Renesas Electronics Corporation |
| * Copyright (C) 2013 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> |
| */ |
| |
| #define LOG_CATEGORY UCLASS_SPI |
| |
| #include <common.h> |
| #include <console.h> |
| #include <malloc.h> |
| #include <spi.h> |
| #include <wait_bit.h> |
| #include <asm/arch/rmobile.h> |
| #include <asm/io.h> |
| #include <linux/bitops.h> |
| |
| /* SH QSPI register bit masks <REG>_<BIT> */ |
| #define SPCR_MSTR 0x08 |
| #define SPCR_SPE 0x40 |
| #define SPSR_SPRFF 0x80 |
| #define SPSR_SPTEF 0x20 |
| #define SPPCR_IO3FV 0x04 |
| #define SPPCR_IO2FV 0x02 |
| #define SPPCR_IO1FV 0x01 |
| #define SPBDCR_RXBC0 BIT(0) |
| #define SPCMD_SCKDEN BIT(15) |
| #define SPCMD_SLNDEN BIT(14) |
| #define SPCMD_SPNDEN BIT(13) |
| #define SPCMD_SSLKP BIT(7) |
| #define SPCMD_BRDV0 BIT(2) |
| #define SPCMD_INIT1 SPCMD_SCKDEN | SPCMD_SLNDEN | \ |
| SPCMD_SPNDEN | SPCMD_SSLKP | \ |
| SPCMD_BRDV0 |
| #define SPCMD_INIT2 SPCMD_SPNDEN | SPCMD_SSLKP | \ |
| SPCMD_BRDV0 |
| #define SPBFCR_TXRST BIT(7) |
| #define SPBFCR_RXRST BIT(6) |
| #define SPBFCR_TXTRG 0x30 |
| #define SPBFCR_RXTRG 0x07 |
| |
| /* SH QSPI register set */ |
| struct sh_qspi_regs { |
| u8 spcr; |
| u8 sslp; |
| u8 sppcr; |
| u8 spsr; |
| u32 spdr; |
| u8 spscr; |
| u8 spssr; |
| u8 spbr; |
| u8 spdcr; |
| u8 spckd; |
| u8 sslnd; |
| u8 spnd; |
| u8 dummy0; |
| u16 spcmd0; |
| u16 spcmd1; |
| u16 spcmd2; |
| u16 spcmd3; |
| u8 spbfcr; |
| u8 dummy1; |
| u16 spbdcr; |
| u32 spbmul0; |
| u32 spbmul1; |
| u32 spbmul2; |
| u32 spbmul3; |
| }; |
| |
| struct sh_qspi_slave { |
| #if !CONFIG_IS_ENABLED(DM_SPI) |
| struct spi_slave slave; |
| #endif |
| struct sh_qspi_regs *regs; |
| }; |
| |
| static void sh_qspi_init(struct sh_qspi_slave *ss) |
| { |
| /* QSPI initialize */ |
| /* Set master mode only */ |
| writeb(SPCR_MSTR, &ss->regs->spcr); |
| |
| /* Set SSL signal level */ |
| writeb(0x00, &ss->regs->sslp); |
| |
| /* Set MOSI signal value when transfer is in idle state */ |
| writeb(SPPCR_IO3FV|SPPCR_IO2FV, &ss->regs->sppcr); |
| |
| /* Set bit rate. See 58.3.8 Quad Serial Peripheral Interface */ |
| writeb(0x01, &ss->regs->spbr); |
| |
| /* Disable Dummy Data Transmission */ |
| writeb(0x00, &ss->regs->spdcr); |
| |
| /* Set clock delay value */ |
| writeb(0x00, &ss->regs->spckd); |
| |
| /* Set SSL negation delay value */ |
| writeb(0x00, &ss->regs->sslnd); |
| |
| /* Set next-access delay value */ |
| writeb(0x00, &ss->regs->spnd); |
| |
| /* Set equence command */ |
| writew(SPCMD_INIT2, &ss->regs->spcmd0); |
| |
| /* Reset transfer and receive Buffer */ |
| setbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST); |
| |
| /* Clear transfer and receive Buffer control bit */ |
| clrbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST); |
| |
| /* Set equence control method. Use equence0 only */ |
| writeb(0x00, &ss->regs->spscr); |
| |
| /* Enable SPI function */ |
| setbits_8(&ss->regs->spcr, SPCR_SPE); |
| } |
| |
| static void sh_qspi_cs_activate(struct sh_qspi_slave *ss) |
| { |
| /* Set master mode only */ |
| writeb(SPCR_MSTR, &ss->regs->spcr); |
| |
| /* Set command */ |
| writew(SPCMD_INIT1, &ss->regs->spcmd0); |
| |
| /* Reset transfer and receive Buffer */ |
| setbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST); |
| |
| /* Clear transfer and receive Buffer control bit */ |
| clrbits_8(&ss->regs->spbfcr, SPBFCR_TXRST|SPBFCR_RXRST); |
| |
| /* Set equence control method. Use equence0 only */ |
| writeb(0x00, &ss->regs->spscr); |
| |
| /* Enable SPI function */ |
| setbits_8(&ss->regs->spcr, SPCR_SPE); |
| } |
| |
| static void sh_qspi_cs_deactivate(struct sh_qspi_slave *ss) |
| { |
| /* Disable SPI Function */ |
| clrbits_8(&ss->regs->spcr, SPCR_SPE); |
| } |
| |
| static int sh_qspi_xfer_common(struct sh_qspi_slave *ss, unsigned int bitlen, |
| const void *dout, void *din, unsigned long flags) |
| { |
| u32 nbyte, chunk; |
| int i, ret = 0; |
| u8 dtdata = 0, drdata; |
| u8 *tdata = &dtdata, *rdata = &drdata; |
| u32 *spbmul0 = &ss->regs->spbmul0; |
| |
| if (dout == NULL && din == NULL) { |
| if (flags & SPI_XFER_END) |
| sh_qspi_cs_deactivate(ss); |
| return 0; |
| } |
| |
| if (bitlen % 8) { |
| log_warning("bitlen is not 8bit aligned %d", bitlen); |
| return 1; |
| } |
| |
| nbyte = bitlen / 8; |
| |
| if (flags & SPI_XFER_BEGIN) { |
| sh_qspi_cs_activate(ss); |
| |
| /* Set 1048576 byte */ |
| writel(0x100000, spbmul0); |
| } |
| |
| if (flags & SPI_XFER_END) |
| writel(nbyte, spbmul0); |
| |
| if (dout != NULL) |
| tdata = (u8 *)dout; |
| |
| if (din != NULL) |
| rdata = din; |
| |
| while (nbyte > 0) { |
| /* |
| * Check if there is 32 Byte chunk and if there is, transfer |
| * it in one burst, otherwise transfer on byte-by-byte basis. |
| */ |
| chunk = (nbyte >= 32) ? 32 : 1; |
| |
| clrsetbits_8(&ss->regs->spbfcr, SPBFCR_TXTRG | SPBFCR_RXTRG, |
| chunk == 32 ? SPBFCR_TXTRG | SPBFCR_RXTRG : 0); |
| |
| ret = wait_for_bit_8(&ss->regs->spsr, SPSR_SPTEF, |
| true, 1000, true); |
| if (ret) |
| return ret; |
| |
| for (i = 0; i < chunk; i++) { |
| writeb(*tdata, &ss->regs->spdr); |
| if (dout != NULL) |
| tdata++; |
| } |
| |
| ret = wait_for_bit_8(&ss->regs->spsr, SPSR_SPRFF, |
| true, 1000, true); |
| if (ret) |
| return ret; |
| |
| for (i = 0; i < chunk; i++) { |
| *rdata = readb(&ss->regs->spdr); |
| if (din != NULL) |
| rdata++; |
| } |
| |
| nbyte -= chunk; |
| } |
| |
| if (flags & SPI_XFER_END) |
| sh_qspi_cs_deactivate(ss); |
| |
| return ret; |
| } |
| |
| #if !CONFIG_IS_ENABLED(DM_SPI) |
| static inline struct sh_qspi_slave *to_sh_qspi(struct spi_slave *slave) |
| { |
| return container_of(slave, struct sh_qspi_slave, slave); |
| } |
| |
| int spi_cs_is_valid(unsigned int bus, unsigned int cs) |
| { |
| return 1; |
| } |
| |
| void spi_cs_activate(struct spi_slave *slave) |
| { |
| struct sh_qspi_slave *ss = to_sh_qspi(slave); |
| |
| sh_qspi_cs_activate(ss); |
| } |
| |
| void spi_cs_deactivate(struct spi_slave *slave) |
| { |
| struct sh_qspi_slave *ss = to_sh_qspi(slave); |
| |
| sh_qspi_cs_deactivate(ss); |
| } |
| |
| struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, |
| unsigned int max_hz, unsigned int mode) |
| { |
| struct sh_qspi_slave *ss; |
| |
| if (!spi_cs_is_valid(bus, cs)) |
| return NULL; |
| |
| ss = spi_alloc_slave(struct sh_qspi_slave, bus, cs); |
| if (!ss) { |
| printf("SPI_error: Fail to allocate sh_qspi_slave\n"); |
| return NULL; |
| } |
| |
| ss->regs = (struct sh_qspi_regs *)SH_QSPI_BASE; |
| |
| /* Init SH QSPI */ |
| sh_qspi_init(ss); |
| |
| return &ss->slave; |
| } |
| |
| void spi_free_slave(struct spi_slave *slave) |
| { |
| struct sh_qspi_slave *spi = to_sh_qspi(slave); |
| |
| free(spi); |
| } |
| |
| int spi_claim_bus(struct spi_slave *slave) |
| { |
| return 0; |
| } |
| |
| void spi_release_bus(struct spi_slave *slave) |
| { |
| } |
| |
| int spi_xfer(struct spi_slave *slave, unsigned int bitlen, |
| const void *dout, void *din, unsigned long flags) |
| { |
| struct sh_qspi_slave *ss = to_sh_qspi(slave); |
| |
| return sh_qspi_xfer_common(ss, bitlen, dout, din, flags); |
| } |
| |
| #else |
| |
| #include <dm.h> |
| |
| static int sh_qspi_xfer(struct udevice *dev, unsigned int bitlen, |
| const void *dout, void *din, unsigned long flags) |
| { |
| struct udevice *bus = dev->parent; |
| struct sh_qspi_slave *ss = dev_get_plat(bus); |
| |
| return sh_qspi_xfer_common(ss, bitlen, dout, din, flags); |
| } |
| |
| static int sh_qspi_set_speed(struct udevice *dev, uint speed) |
| { |
| /* This is a SPI NOR controller, do nothing. */ |
| return 0; |
| } |
| |
| static int sh_qspi_set_mode(struct udevice *dev, uint mode) |
| { |
| /* This is a SPI NOR controller, do nothing. */ |
| return 0; |
| } |
| |
| static int sh_qspi_probe(struct udevice *dev) |
| { |
| struct sh_qspi_slave *ss = dev_get_plat(dev); |
| |
| sh_qspi_init(ss); |
| |
| return 0; |
| } |
| |
| static int sh_qspi_of_to_plat(struct udevice *dev) |
| { |
| struct sh_qspi_slave *plat = dev_get_plat(dev); |
| |
| plat->regs = dev_read_addr_ptr(dev); |
| |
| return 0; |
| } |
| |
| static const struct dm_spi_ops sh_qspi_ops = { |
| .xfer = sh_qspi_xfer, |
| .set_speed = sh_qspi_set_speed, |
| .set_mode = sh_qspi_set_mode, |
| }; |
| |
| static const struct udevice_id sh_qspi_ids[] = { |
| { .compatible = "renesas,qspi" }, |
| { } |
| }; |
| |
| U_BOOT_DRIVER(sh_qspi) = { |
| .name = "sh_qspi", |
| .id = UCLASS_SPI, |
| .of_match = sh_qspi_ids, |
| .ops = &sh_qspi_ops, |
| .of_to_plat = sh_qspi_of_to_plat, |
| .plat_auto = sizeof(struct sh_qspi_slave), |
| .probe = sh_qspi_probe, |
| }; |
| #endif |