| /* |
| * Copyright (C) 2007 Freescale Semiconductor, Inc. |
| * Dave Liu <daveliu@freescale.com> |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #undef DEBUG |
| |
| /* |
| * High Level Configuration Options |
| */ |
| #define CONFIG_E300 1 /* E300 family */ |
| #define CONFIG_MPC83XX 1 /* MPC83XX family */ |
| #define CONFIG_MPC837X 1 /* MPC837X CPU specific */ |
| #define CONFIG_MPC837XEMDS 1 /* MPC837XEMDS board specific */ |
| |
| /* |
| * System Clock Setup |
| */ |
| #ifdef CONFIG_PCISLAVE |
| #define CONFIG_83XX_PCICLK 66000000 /* in HZ */ |
| #else |
| #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ |
| #endif |
| |
| #ifndef CONFIG_SYS_CLK_FREQ |
| #define CONFIG_SYS_CLK_FREQ 66000000 |
| #endif |
| |
| /* |
| * Hardware Reset Configuration Word |
| * if CLKIN is 66MHz, then |
| * CSB = 396MHz, CORE = 594MHz, DDRC = 396MHz, LBC = 396MHz |
| */ |
| #define CFG_HRCW_LOW (\ |
| HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ |
| HRCWL_DDR_TO_SCB_CLK_1X1 |\ |
| HRCWL_SVCOD_DIV_2 |\ |
| HRCWL_CSB_TO_CLKIN_6X1 |\ |
| HRCWL_CORE_TO_CSB_1_5X1) |
| |
| #ifdef CONFIG_PCISLAVE |
| #define CFG_HRCW_HIGH (\ |
| HRCWH_PCI_AGENT |\ |
| HRCWH_PCI1_ARBITER_DISABLE |\ |
| HRCWH_CORE_ENABLE |\ |
| HRCWH_FROM_0XFFF00100 |\ |
| HRCWH_BOOTSEQ_DISABLE |\ |
| HRCWH_SW_WATCHDOG_DISABLE |\ |
| HRCWH_ROM_LOC_LOCAL_16BIT |\ |
| HRCWH_RL_EXT_LEGACY |\ |
| HRCWH_TSEC1M_IN_RGMII |\ |
| HRCWH_TSEC2M_IN_RGMII |\ |
| HRCWH_BIG_ENDIAN |\ |
| HRCWH_LDP_CLEAR) |
| #else |
| #define CFG_HRCW_HIGH (\ |
| HRCWH_PCI_HOST |\ |
| HRCWH_PCI1_ARBITER_ENABLE |\ |
| HRCWH_CORE_ENABLE |\ |
| HRCWH_FROM_0X00000100 |\ |
| HRCWH_BOOTSEQ_DISABLE |\ |
| HRCWH_SW_WATCHDOG_DISABLE |\ |
| HRCWH_ROM_LOC_LOCAL_16BIT |\ |
| HRCWH_RL_EXT_LEGACY |\ |
| HRCWH_TSEC1M_IN_RGMII |\ |
| HRCWH_TSEC2M_IN_RGMII |\ |
| HRCWH_BIG_ENDIAN |\ |
| HRCWH_LDP_CLEAR) |
| #endif |
| |
| /* |
| * eTSEC Clock Config |
| */ |
| #define CFG_SCCR_TSEC1CM 1 /* CSB:eTSEC1 = 1:1 */ |
| #define CFG_SCCR_TSEC2CM 1 /* CSB:eTSEC2 = 1:1 */ |
| |
| /* |
| * System IO Config |
| */ |
| #define CFG_SICRH 0x00000000 |
| #define CFG_SICRL 0x00000000 |
| |
| /* |
| * Output Buffer Impedance |
| */ |
| #define CFG_OBIR 0x31100000 |
| |
| #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */ |
| #define CONFIG_BOARD_EARLY_INIT_R |
| |
| /* |
| * IMMR new address |
| */ |
| #define CFG_IMMR 0xE0000000 |
| |
| /* |
| * DDR Setup |
| */ |
| #define CFG_DDR_BASE 0x00000000 /* DDR is system memory */ |
| #define CFG_SDRAM_BASE CFG_DDR_BASE |
| #define CFG_DDR_SDRAM_BASE CFG_DDR_BASE |
| #define CFG_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 |
| #define CFG_83XX_DDR_USES_CS0 |
| #define CFG_DDRCDR_VALUE 0x80080001 /* ODT 150ohm on SoC */ |
| |
| #undef CONFIG_DDR_ECC /* support DDR ECC function */ |
| #undef CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ |
| |
| #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ |
| #define CONFIG_NEVER_ASSERT_ODT_TO_CPU /* Never assert ODT to internal IOs */ |
| |
| #if defined(CONFIG_SPD_EEPROM) |
| #define SPD_EEPROM_ADDRESS 0x51 /* I2C address of DDR SODIMM SPD */ |
| #else |
| /* |
| * Manually set up DDR parameters |
| * WHITE ELECTRONIC DESGGNS - W3HG64M72EEU403PD4 SO-DIMM |
| * consist of nine chips from SAMSUNG K4T51083QE-ZC(L)D5 |
| */ |
| #define CFG_DDR_SIZE 512 /* MB */ |
| #define CFG_DDR_CS0_BNDS 0x0000001f |
| #define CFG_DDR_CS0_CONFIG ( CSCONFIG_EN \ |
| | 0x00010000 /* ODT_WR to CSn */ \ |
| | CSCONFIG_ROW_BIT_14 | CSCONFIG_COL_BIT_10 ) |
| /* 0x80010202 */ |
| #define CFG_DDR_TIMING_3 0x00000000 |
| #define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \ |
| | ( 0 << TIMING_CFG0_WRT_SHIFT ) \ |
| | ( 0 << TIMING_CFG0_RRT_SHIFT ) \ |
| | ( 0 << TIMING_CFG0_WWT_SHIFT ) \ |
| | ( 6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \ |
| | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \ |
| | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \ |
| | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) ) |
| /* 0x00620802 */ |
| #define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \ |
| | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \ |
| | ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \ |
| | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \ |
| | (13 << TIMING_CFG1_REFREC_SHIFT ) \ |
| | ( 3 << TIMING_CFG1_WRREC_SHIFT ) \ |
| | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \ |
| | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) ) |
| /* 0x3935d322 */ |
| #define CFG_DDR_TIMING_2 ( ( 2 << TIMING_CFG2_ADD_LAT_SHIFT ) \ |
| | ( 6 << TIMING_CFG2_CPO_SHIFT ) \ |
| | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \ |
| | ( 4 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \ |
| | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \ |
| | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \ |
| | ( 8 << TIMING_CFG2_FOUR_ACT_SHIFT) ) |
| /* 0x231088c8 */ |
| #define CFG_DDR_INTERVAL ( ( 0x03E0 << SDRAM_INTERVAL_REFINT_SHIFT ) \ |
| | ( 0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) ) |
| /* 0x03E00100 */ |
| #define CFG_DDR_SDRAM_CFG 0x43000000 |
| #define CFG_DDR_SDRAM_CFG2 0x00001000 /* 1 posted refresh */ |
| #define CFG_DDR_MODE ( ( 0x0450 << SDRAM_MODE_ESD_SHIFT ) \ |
| | ( 0x1432 << SDRAM_MODE_SD_SHIFT ) ) |
| /* ODT 150ohm CL=3, AL=2 on SDRAM */ |
| #define CFG_DDR_MODE2 0x00000000 |
| #endif |
| |
| /* |
| * Memory test |
| */ |
| #undef CFG_DRAM_TEST /* memory test, takes time */ |
| #define CFG_MEMTEST_START 0x00040000 /* memtest region */ |
| #define CFG_MEMTEST_END 0x00140000 |
| |
| /* |
| * The reserved memory |
| */ |
| #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ |
| |
| #if (CFG_MONITOR_BASE < CFG_FLASH_BASE) |
| #define CFG_RAMBOOT |
| #else |
| #undef CFG_RAMBOOT |
| #endif |
| |
| /* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */ |
| #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ |
| #define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */ |
| |
| /* |
| * Initial RAM Base Address Setup |
| */ |
| #define CFG_INIT_RAM_LOCK 1 |
| #define CFG_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ |
| #define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM */ |
| #define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ |
| #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) |
| |
| /* |
| * Local Bus Configuration & Clock Setup |
| */ |
| #define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_8) |
| #define CFG_LBC_LBCR 0x00000000 |
| |
| /* |
| * FLASH on the Local Bus |
| */ |
| #define CFG_FLASH_CFI /* use the Common Flash Interface */ |
| #define CFG_FLASH_CFI_DRIVER /* use the CFI driver */ |
| #define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */ |
| #define CFG_FLASH_SIZE 32 /* max FLASH size is 32M */ |
| |
| #define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */ |
| #define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */ |
| |
| #define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \ |
| (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ |
| BR_V) /* valid */ |
| #define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ |
| OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ |
| OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) |
| |
| #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ |
| #define CFG_MAX_FLASH_SECT 256 /* max sectors per device */ |
| |
| #undef CFG_FLASH_CHECKSUM |
| #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ |
| #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ |
| |
| /* |
| * BCSR on the Local Bus |
| */ |
| #define CFG_BCSR 0xF8000000 |
| #define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */ |
| #define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */ |
| |
| #define CFG_BR1_PRELIM (CFG_BCSR | 0x00000801) /* Port size=8bit, MSEL=GPCM */ |
| #define CFG_OR1_PRELIM 0xFFFFE9f7 /* length 32K */ |
| |
| /* |
| * NAND Flash on the Local Bus |
| */ |
| #define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */ |
| #define CFG_BR3_PRELIM ( CFG_NAND_BASE \ |
| | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ |
| | BR_PS_8 /* Port Size = 8 bit */ \ |
| | BR_MS_FCM /* MSEL = FCM */ \ |
| | BR_V ) /* valid */ |
| #define CFG_OR3_PRELIM ( 0xFFFF8000 /* length 32K */ \ |
| | OR_FCM_CSCT \ |
| | OR_FCM_CST \ |
| | OR_FCM_CHT \ |
| | OR_FCM_SCY_1 \ |
| | OR_FCM_TRLX \ |
| | OR_FCM_EHTR ) |
| /* 0xFFFF8396 */ |
| |
| #define CFG_LBLAWBAR3_PRELIM CFG_NAND_BASE |
| #define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */ |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_CONS_INDEX 1 |
| #undef CONFIG_SERIAL_SOFTWARE_FIFO |
| #define CFG_NS16550 |
| #define CFG_NS16550_SERIAL |
| #define CFG_NS16550_REG_SIZE 1 |
| #define CFG_NS16550_CLK get_bus_freq(0) |
| |
| #define CFG_BAUDRATE_TABLE \ |
| {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} |
| |
| #define CFG_NS16550_COM1 (CFG_IMMR+0x4500) |
| #define CFG_NS16550_COM2 (CFG_IMMR+0x4600) |
| |
| /* Use the HUSH parser */ |
| #define CFG_HUSH_PARSER |
| #ifdef CFG_HUSH_PARSER |
| #define CFG_PROMPT_HUSH_PS2 "> " |
| #endif |
| |
| /* Pass open firmware flat tree */ |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_OF_BOARD_SETUP 1 |
| #define CONFIG_OF_STDOUT_VIA_ALIAS 1 |
| |
| /* I2C */ |
| #define CONFIG_HARD_I2C /* I2C with hardware support */ |
| #undef CONFIG_SOFT_I2C /* I2C bit-banged */ |
| #define CONFIG_FSL_I2C |
| #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ |
| #define CFG_I2C_SLAVE 0x7F |
| #define CFG_I2C_NOPROBES {0x51} /* Don't probe these addrs */ |
| #define CFG_I2C_OFFSET 0x3000 |
| #define CFG_I2C2_OFFSET 0x3100 |
| |
| /* |
| * Config on-board RTC |
| */ |
| #define CONFIG_RTC_DS1374 /* use ds1374 rtc via i2c */ |
| #define CFG_I2C_RTC_ADDR 0x68 /* at address 0x68 */ |
| |
| /* |
| * General PCI |
| * Addresses are mapped 1-1. |
| */ |
| #define CFG_PCI_MEM_BASE 0x80000000 |
| #define CFG_PCI_MEM_PHYS CFG_PCI_MEM_BASE |
| #define CFG_PCI_MEM_SIZE 0x10000000 /* 256M */ |
| #define CFG_PCI_MMIO_BASE 0x90000000 |
| #define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE |
| #define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */ |
| #define CFG_PCI_IO_BASE 0xE0300000 |
| #define CFG_PCI_IO_PHYS 0xE0300000 |
| #define CFG_PCI_IO_SIZE 0x100000 /* 1M */ |
| |
| #define CFG_PCI_SLV_MEM_LOCAL CFG_SDRAM_BASE |
| #define CFG_PCI_SLV_MEM_BUS 0x00000000 |
| #define CFG_PCI_SLV_MEM_SIZE 0x80000000 |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_83XX_GENERIC_PCI 1 /* Use generic PCI setup */ |
| #define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */ |
| |
| #define CONFIG_NET_MULTI |
| #define CONFIG_PCI_PNP /* do pci plug-and-play */ |
| |
| #undef CONFIG_EEPRO100 |
| #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ |
| #define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ |
| #endif /* CONFIG_PCI */ |
| |
| #ifndef CONFIG_NET_MULTI |
| #define CONFIG_NET_MULTI 1 |
| #endif |
| |
| /* |
| * TSEC |
| */ |
| #define CONFIG_TSEC_ENET /* TSEC ethernet support */ |
| #define CFG_TSEC1_OFFSET 0x24000 |
| #define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET) |
| #define CFG_TSEC2_OFFSET 0x25000 |
| #define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET) |
| |
| /* |
| * TSEC ethernet configuration |
| */ |
| #define CONFIG_MII 1 /* MII PHY management */ |
| #define CONFIG_TSEC1 1 |
| #define CONFIG_TSEC1_NAME "eTSEC0" |
| #define CONFIG_TSEC2 1 |
| #define CONFIG_TSEC2_NAME "eTSEC1" |
| #define TSEC1_PHY_ADDR 2 |
| #define TSEC2_PHY_ADDR 3 |
| #define TSEC1_PHYIDX 0 |
| #define TSEC2_PHYIDX 0 |
| #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) |
| |
| /* Options are: TSEC[0-1] */ |
| #define CONFIG_ETHPRIME "eTSEC1" |
| |
| /* |
| * Environment |
| */ |
| #ifndef CFG_RAMBOOT |
| #define CFG_ENV_IS_IN_FLASH 1 |
| #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) |
| #define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ |
| #define CFG_ENV_SIZE 0x2000 |
| #else |
| #define CFG_NO_FLASH 1 /* Flash is not usable now */ |
| #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ |
| #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) |
| #define CFG_ENV_SIZE 0x2000 |
| #endif |
| |
| #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ |
| #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| |
| |
| /* |
| * Command line configuration. |
| */ |
| #include <config_cmd_default.h> |
| |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_DATE |
| |
| #if defined(CONFIG_PCI) |
| #define CONFIG_CMD_PCI |
| #endif |
| |
| #if defined(CFG_RAMBOOT) |
| #undef CONFIG_CMD_ENV |
| #undef CONFIG_CMD_LOADS |
| #endif |
| |
| #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ |
| |
| #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CFG_LONGHELP /* undef to save memory */ |
| #define CFG_LOAD_ADDR 0x2000000 /* default load address */ |
| #define CFG_PROMPT "=> " /* Monitor Command Prompt */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #else |
| #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ |
| #endif |
| |
| #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ |
| #define CFG_MAXARGS 16 /* max number of command args */ |
| #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ |
| #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
| |
| /* |
| * Core HID Setup |
| */ |
| #define CFG_HID0_INIT 0x000000000 |
| #define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK |
| #define CFG_HID2 HID2_HBE |
| |
| /* |
| * Cache Config |
| */ |
| #define CFG_DCACHE_SIZE 32768 |
| #define CFG_CACHELINE_SIZE 32 |
| #if defined(CONFIG_CMD_KGDB) |
| #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */ |
| #endif |
| |
| /* |
| * MMU Setup |
| */ |
| |
| /* DDR: cache cacheable */ |
| #define CFG_SDRAM_LOWER CFG_SDRAM_BASE |
| #define CFG_SDRAM_UPPER (CFG_SDRAM_BASE + 0x10000000) |
| |
| #define CFG_IBAT0L (CFG_SDRAM_LOWER | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CFG_IBAT0U (CFG_SDRAM_LOWER | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CFG_DBAT0L CFG_IBAT0L |
| #define CFG_DBAT0U CFG_IBAT0U |
| |
| #define CFG_IBAT1L (CFG_SDRAM_UPPER | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CFG_IBAT1U (CFG_SDRAM_UPPER | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CFG_DBAT1L CFG_IBAT1L |
| #define CFG_DBAT1U CFG_IBAT1U |
| |
| /* IMMRBAR, PCI IO and NAND: cache-inhibit and guarded */ |
| #define CFG_IBAT2L (CFG_IMMR | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CFG_IBAT2U (CFG_IMMR | BATU_BL_8M | BATU_VS | BATU_VP) |
| #define CFG_DBAT2L CFG_IBAT2L |
| #define CFG_DBAT2U CFG_IBAT2U |
| |
| /* BCSR: cache-inhibit and guarded */ |
| #define CFG_IBAT3L (CFG_BCSR | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CFG_IBAT3U (CFG_BCSR | BATU_BL_128K | BATU_VS | BATU_VP) |
| #define CFG_DBAT3L CFG_IBAT3L |
| #define CFG_DBAT3U CFG_IBAT3U |
| |
| /* FLASH: icache cacheable, but dcache-inhibit and guarded */ |
| #define CFG_IBAT4L (CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CFG_IBAT4U (CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP) |
| #define CFG_DBAT4L (CFG_FLASH_BASE | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CFG_DBAT4U CFG_IBAT4U |
| |
| /* Stack in dcache: cacheable, no memory coherence */ |
| #define CFG_IBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_10) |
| #define CFG_IBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) |
| #define CFG_DBAT5L CFG_IBAT5L |
| #define CFG_DBAT5U CFG_IBAT5U |
| |
| #ifdef CONFIG_PCI |
| /* PCI MEM space: cacheable */ |
| #define CFG_IBAT6L (CFG_PCI_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) |
| #define CFG_IBAT6U (CFG_PCI_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CFG_DBAT6L CFG_IBAT6L |
| #define CFG_DBAT6U CFG_IBAT6U |
| /* PCI MMIO space: cache-inhibit and guarded */ |
| #define CFG_IBAT7L (CFG_PCI_MMIO_PHYS | BATL_PP_10 | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CFG_IBAT7U (CFG_PCI_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) |
| #define CFG_DBAT7L CFG_IBAT7L |
| #define CFG_DBAT7U CFG_IBAT7U |
| #else |
| #define CFG_IBAT6L (0) |
| #define CFG_IBAT6U (0) |
| #define CFG_IBAT7L (0) |
| #define CFG_IBAT7U (0) |
| #define CFG_DBAT6L CFG_IBAT6L |
| #define CFG_DBAT6U CFG_IBAT6U |
| #define CFG_DBAT7L CFG_IBAT7L |
| #define CFG_DBAT7U CFG_IBAT7U |
| #endif |
| |
| /* |
| * Internal Definitions |
| * |
| * Boot Flags |
| */ |
| #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ |
| #define BOOTFLAG_WARM 0x02 /* Software reboot */ |
| |
| #if defined(CONFIG_CMD_KGDB) |
| #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ |
| #endif |
| |
| /* |
| * Environment Configuration |
| */ |
| |
| #define CONFIG_ENV_OVERWRITE |
| |
| #if defined(CONFIG_TSEC_ENET) |
| #define CONFIG_HAS_ETH0 |
| #define CONFIG_ETHADDR 00:E0:0C:00:83:79 |
| #define CONFIG_HAS_ETH1 |
| #define CONFIG_ETH1ADDR 00:E0:0C:00:83:78 |
| #endif |
| |
| #define CONFIG_BAUDRATE 115200 |
| |
| #define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */ |
| |
| #define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ |
| #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "netdev=eth0\0" \ |
| "consoledev=ttyS0\0" \ |
| "ramdiskaddr=1000000\0" \ |
| "ramdiskfile=ramfs.83xx\0" \ |
| "fdtaddr=400000\0" \ |
| "fdtfile=mpc837xemds.dtb\0" \ |
| "" |
| |
| #define CONFIG_NFSBOOTCOMMAND \ |
| "setenv bootargs root=/dev/nfs rw " \ |
| "nfsroot=$serverip:$rootpath " \ |
| "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr - $fdtaddr" |
| |
| #define CONFIG_RAMBOOTCOMMAND \ |
| "setenv bootargs root=/dev/ram rw " \ |
| "console=$consoledev,$baudrate $othbootargs;" \ |
| "tftp $ramdiskaddr $ramdiskfile;" \ |
| "tftp $loadaddr $bootfile;" \ |
| "tftp $fdtaddr $fdtfile;" \ |
| "bootm $loadaddr $ramdiskaddr $fdtaddr" |
| |
| |
| #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND |
| |
| #endif /* __CONFIG_H */ |