commit 5d2a5ef712914fe1c3edfcde78134dc4dc83f461
author Masahiro Yamada <yamada.m@jp.panasonic.com> Mon Dec 15 23:26:06 2014 +0900
committer Tom Rini <trini@ti.com> Mon Jan 05 12:08:50 2015 -0500
tree cbef611c664ab229fff50bd5947f563a4cc3a139
parent a2ee47d5f6d010e92e956a8fa9b62fe220d61bf6

mpc8xx: remove FPS{850, 860}L, NSCU, SM850, TK885D, virtlab2 support

These boards are still non-generic boards.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>

board/tqc/tqm8xx/tqm8xx.c

diff --git a/board/tqc/tqm8xx/tqm8xx.c b/board/tqc/tqm8xx/tqm8xx.c
index 3b5230a..6d17830 100644
--- a/board/tqc/tqm8xx/tqm8xx.c
+++ b/board/tqc/tqm8xx/tqm8xx.c
@@ -118,9 +118,7 @@
 			break;
 		putc (buf[i]);
 	}
-#ifdef CONFIG_VIRTLAB2
-	puts (" (Virtlab2)");
-#endif
+
 	putc ('\n');
 
 	return (0);
@@ -512,14 +510,6 @@
 	immap->im_ioport.iop_padat &= ~0x0001;	/* turn it off */
 # endif
 
-#ifdef CONFIG_NSCU
-	/* wake up ethernet module */
-	immap->im_ioport.iop_pcpar &= ~0x0004;	/* GPIO pin      */
-	immap->im_ioport.iop_pcdir |= 0x0004;	/* output        */
-	immap->im_ioport.iop_pcso &= ~0x0004;	/* for clarity   */
-	immap->im_ioport.iop_pcdat |= 0x0004;	/* enable        */
-#endif /* CONFIG_NSCU */
-
 	return (0);
 }
 #endif	/* CONFIG_MISC_INIT_R */
@@ -682,49 +672,3 @@
 	return 0;
 }
 #endif /* defined(CONFIG_OF_BOARD_SETUP) && defined(CONFIG_OF_LIBFDT) */
-
-/* ---------------------------------------------------------------------------- */
-/* TK885D specific initializaion						*/
-/* ---------------------------------------------------------------------------- */
-#ifdef CONFIG_TK885D
-#include <miiphy.h>
-int last_stage_init(void)
-{
-	const unsigned char phy[] = {CONFIG_FEC1_PHY, CONFIG_FEC2_PHY};
-	unsigned short reg;
-	int ret, i = 100;
-	char *s;
-
-	mii_init();
-	/* Without this delay 0xff is read from the UART buffer later in
-	 * abortboot() and autoboot is aborted */
-	udelay(10000);
-	while (tstc() && i--)
-		(void)getc();
-
-	/* Check if auto-negotiation is prohibited */
-	s = getenv("phy_auto_nego");
-
-	if (!s || !strcmp(s, "on"))
-		/* Nothing to do - autonegotiation by default */
-		return 0;
-
-	for (i = 0; i < 2; i++) {
-		ret = miiphy_read("FEC", phy[i], MII_BMCR, &reg);
-		if (ret) {
-			printf("Cannot read BMCR on PHY %d\n", phy[i]);
-			return 0;
-		}
-		/* Auto-negotiation off, hard set full duplex, 100Mbps */
-		ret = miiphy_write("FEC", phy[i],
-				   MII_BMCR, (reg | BMCR_SPEED100 |
-					      BMCR_FULLDPLX) & ~BMCR_ANENABLE);
-		if (ret) {
-			printf("Cannot write BMCR on PHY %d\n", phy[i]);
-			return 0;
-		}
-	}
-
-	return 0;
-}
-#endif