include/configs/kmcoge5ne.h - platform/external/u-boot - Gitiles

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * (C) Copyright 2012
  * Holger Brunck, Keymile GmbH Hannover, <holger.brunck@keymile.com>
  * Christian Herzig, Keymile AG Switzerland, <christian.herzig@keymile.com>
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /* KMBEC FPGA (PRIO) */
 #define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
 #define CONFIG_SYS_KMBEC_FPGA_SIZE	64

 #define CONFIG_HOSTNAME		"kmcoge5ne"
 #define CONFIG_KM_BOARD_NAME	"kmcoge5ne"
 #define CONFIG_KM_DEF_NETDEV	"netdev=eth1\0"
 #define CONFIG_NAND_ECC_BCH
 #define CONFIG_NAND_KMETER1
 #define CONFIG_SYS_MAX_NAND_DEVICE		1
 #define NAND_MAX_CHIPS				1
 #define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */

 #define CONFIG_KM_UBI_PARTITION_NAME_BOOT	"ubi0"
 #define CONFIG_KM_UBI_PARTITION_NAME_APP	"ubi1"

 /*
  * High Level Configuration Options
  */
 #define CONFIG_QE			/* Has QE */

 /* include common defines/options for all Keymile boards */
 #include "km/keymile-common.h"
 #include "km/km-powerpc.h"

 /*
  * System Clock Setup
  */
 #define CONFIG_83XX_CLKIN		66000000
 #define CONFIG_SYS_CLK_FREQ		66000000
 #define CONFIG_83XX_PCICLK		66000000

 /*
  * IMMR new address
  */
 #define CONFIG_SYS_IMMR		0xE0000000

 /*
  * Bus Arbitration Configuration Register (ACR)
  */
 #define CONFIG_SYS_ACR_PIPE_DEP 3       /* pipeline depth 4 transactions */
 #define CONFIG_SYS_ACR_RPTCNT   3       /* 4 consecutive transactions */
 #define CONFIG_SYS_ACR_APARK    0       /* park bus to master (below) */
 #define CONFIG_SYS_ACR_PARKM    3       /* parking master = QuiccEngine */

 /*
  * DDR Setup
  */
 #define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
 #define CONFIG_SYS_SDRAM_BASE2	(CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */

 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
 					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)

 #define CFG_83XX_DDR_USES_CS0

 /*
  * Manually set up DDR parameters
  */
 #define CONFIG_DDR_II
 #define CONFIG_SYS_DDR_SIZE		2048 /* MB */

 /*
  * The reserved memory
  */
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE /* start of monitor */
 #define CONFIG_SYS_FLASH_BASE		0xF0000000

 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
 #endif

 /* Reserve 768 kB for Mon */
 #define CONFIG_SYS_MONITOR_LEN		(768 * 1024)

 /*
  * Initial RAM Base Address Setup
  */
 #define CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* End of used area in RAM */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
 						GENERATED_GBL_DATA_SIZE)

 /*
  * Init Local Bus Memory Controller:
  *
  * Bank Bus     Machine PortSz  Size  Device
  * ---- ---     ------- ------  -----  ------
  *  0   Local   GPCM    16 bit  256MB FLASH
  *  1   Local   GPCM     8 bit  128MB GPIO/PIGGY
  *
  */
 /*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */

 #define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE | \
 				BR_PS_16 | /* 16 bit port size */ \
 				BR_MS_GPCM | /* MSEL = GPCM */ \
 				BR_V)

 #define CONFIG_SYS_OR0_PRELIM	(OR_AM_256MB | \
 				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
 				OR_GPCM_SCY_5 | \
 				OR_GPCM_TRLX_SET | OR_GPCM_EAD)

 #define CONFIG_SYS_MAX_FLASH_BANKS	1   /* max num of flash banks	*/
 #define CONFIG_SYS_MAX_FLASH_SECT	512 /* max num of sects on one chip */
 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }

 /*
  * PRIO1/PIGGY on the local bus CS1
  */
 /* Window base at flash base */
 #define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_KMBEC_FPGA_BASE | \
 				BR_PS_8 | /* 8 bit port size */ \
 				BR_MS_GPCM | /* MSEL = GPCM */ \
 				BR_V)
 #define CONFIG_SYS_OR1_PRELIM	(OR_AM_64MB | \
 				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
 				OR_GPCM_SCY_2 | \
 				OR_GPCM_TRLX_SET | OR_GPCM_EAD)

 /*
  * Serial Port
  */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)

 /*
  * QE UEC ethernet configuration
  */
 #define CONFIG_UEC_ETH
 #define CONFIG_ETHPRIME		"UEC0"

 #define CONFIG_UEC_ETH1		/* GETH1 */
 #define UEC_VERBOSE_DEBUG	1

 #ifdef CONFIG_UEC_ETH1
 #define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
 #define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE /* not used in RMII Mode */
 #define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
 #define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
 #define CONFIG_SYS_UEC1_PHY_ADDR	0
 #define CONFIG_SYS_UEC1_INTERFACE_TYPE	PHY_INTERFACE_MODE_RMII
 #define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
 #endif

 /*
  * Environment
  */

 #ifndef CONFIG_SYS_RAMBOOT
 #ifndef CONFIG_ENV_ADDR
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + \
 					CONFIG_SYS_MONITOR_LEN)
 #endif
 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
 #ifndef CONFIG_ENV_OFFSET
 #define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)
 #endif

 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + \
 						CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

 #else /* CFG_SYS_RAMBOOT */
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE		0x2000
 #endif /* CFG_SYS_RAMBOOT */

 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_NUM_I2C_BUSES	4
 #define CONFIG_SYS_I2C_MAX_HOPS		1
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	200000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_I2C_OFFSET		0x3000
 #define CONFIG_SYS_FSL_I2C2_SPEED	200000
 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
 #define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
 		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
 		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
 		{1, {I2C_NULL_HOP} } }

 #define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/

 #if defined(CONFIG_CMD_NAND)
 #define CONFIG_NAND_KMETER1
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
 #define CONFIG_SYS_NAND_BASE		CONFIG_SYS_KMBEC_FPGA_BASE
 #endif

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)

 /*
  * Core HID Setup
  */
 #define CONFIG_SYS_HID0_INIT		0x000000000
 #define CONFIG_SYS_HID0_FINAL		(HID0_ENABLE_MACHINE_CHECK | \
 					 HID0_ENABLE_INSTRUCTION_CACHE)
 #define CONFIG_SYS_HID2			HID2_HBE

 /*
  * Internal Definitions
  */
 #define BOOTFLASH_START	0xF0000000

 #define CONFIG_KM_CONSOLE_TTY	"ttyS0"

 /*
  * Environment Configuration
  */
 #define CONFIG_ENV_OVERWRITE
 #ifndef CONFIG_KM_DEF_ENV		/* if not set by keymile-common.h */
 #define CONFIG_KM_DEF_ENV "km-common=empty\0"
 #endif

 #ifndef CONFIG_KM_DEF_ARCH
 #define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
 #endif

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	CONFIG_KM_DEF_ENV						\
 	CONFIG_KM_DEF_ARCH						\
 	"newenv="							\
 		"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && "	\
 		"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0"		\
 	"unlock=yes\0"							\
 	""

 #if defined(CONFIG_UEC_ETH)
 #define CONFIG_HAS_ETH0
 #endif

 /*
  * System IO Setup
  */
 #define CONFIG_SYS_SICRH		(SICRH_UC1EOBI | SICRH_UC2E1OBI)

 /**
  * DDR RAM settings
  */
 #define CONFIG_SYS_DDR_SDRAM_CFG (\
 	SDRAM_CFG_SDRAM_TYPE_DDR2 | \
 	SDRAM_CFG_SREN | \
 	SDRAM_CFG_HSE)

 #define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000

 /**
  * KMCOGE5NE has 512 MB RAM
  */
 #define CONFIG_SYS_DDR_CS0_CONFIG (\
 	CSCONFIG_EN | \
 	CSCONFIG_AP | \
 	CSCONFIG_ODT_WR_ONLY_CURRENT | \
 	CSCONFIG_BANK_BIT_3 | \
 	CSCONFIG_ROW_BIT_13 | \
 	CSCONFIG_COL_BIT_10)

 #define CONFIG_SYS_DDR_CLK_CNTL (\
 	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)

 #define CONFIG_SYS_DDR_INTERVAL (\
 	(0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
 	(0x203 << SDRAM_INTERVAL_REFINT_SHIFT))

 #define CONFIG_SYS_DDR_CS0_BNDS			0x0000007f

 #define CONFIG_SYS_DDRCDR (\
 	DDRCDR_EN | \
 	DDRCDR_Q_DRN)
 #define CONFIG_SYS_DDR_MODE		0x47860452
 #define CONFIG_SYS_DDR_MODE2		0x8080c000

 #define CONFIG_SYS_DDR_TIMING_0 (\
 	(2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
 	(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
 	(6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
 	(2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
 	(0 << TIMING_CFG0_WWT_SHIFT) | \
 	(0 << TIMING_CFG0_RRT_SHIFT) | \
 	(0 << TIMING_CFG0_WRT_SHIFT) | \
 	(0 << TIMING_CFG0_RWT_SHIFT))

 #define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_50) | \
 				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
 				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
 				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
 				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
 				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
 				 (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
 				 (3 << TIMING_CFG1_PRETOACT_SHIFT))

 #define CONFIG_SYS_DDR_TIMING_2 (\
 	(0xa << TIMING_CFG2_FOUR_ACT_SHIFT) | \
 	(3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
 	(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
 	(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
 	(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
 	(5 << TIMING_CFG2_CPO_SHIFT) | \
 	(0 << TIMING_CFG2_ADD_LAT_SHIFT))

 #define CONFIG_SYS_DDR_TIMING_3			0x00000000

 /* EEprom support */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2

 /*
  * Local Bus Configuration & Clock Setup
  */
 #define CONFIG_SYS_LCRR_DBYP		LCRR_DBYP
 #define CONFIG_SYS_LCRR_EADC		LCRR_EADC_2
 #define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_4

 /*
  * PAXE on the local bus CS3
  */
 #define CONFIG_SYS_PAXE_BASE		0xA0000000
 #define CONFIG_SYS_PAXE_SIZE		256

 #define CONFIG_SYS_BR3_PRELIM (\
 	CONFIG_SYS_PAXE_BASE | \
 	BR_PS_8 | \
 	BR_V)

 #define CONFIG_SYS_OR3_PRELIM (\
 	OR_AM_256MB | \
 	OR_GPCM_CSNT | \
 	OR_GPCM_ACS_DIV2 | \
 	OR_GPCM_SCY_2 | \
 	OR_GPCM_TRLX | \
 	OR_GPCM_EAD)

 /*
  * BFTIC3 on the local bus CS4
  */
 #define CONFIG_SYS_BFTIC3_BASE			0xB0000000
 #define CONFIG_SYS_BFTIC3_SIZE			256

 #define CONFIG_SYS_BR4_PRELIM (\
 	CONFIG_SYS_BFTIC3_BASE |\
 	BR_PS_8 | \
 	BR_V)

 #define CONFIG_SYS_OR4_PRELIM (\
 	OR_AM_256MB|\
 	OR_GPCM_CSNT | \
 	OR_GPCM_ACS_DIV2 |\
 	OR_GPCM_SCY_2 |\
 	OR_GPCM_TRLX |\
 	OR_GPCM_EAD)

 /* enable POST tests */
 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY|CONFIG_SYS_POST_MEM_REGIONS)
 #define CONFIG_POST_EXTERNAL_WORD_FUNCS /* use own functions, not generic */
 #define CPM_POST_WORD_ADDR  CONFIG_SYS_MEMTEST_END
 #define CONFIG_TESTPIN_REG  gprt3	/* for kmcoge5ne */
 #define CONFIG_TESTPIN_MASK 0x20	/* for kmcoge5ne */

 #endif /* CONFIG */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* (C) Copyright 2012
	* Holger Brunck, Keymile GmbH Hannover, <holger.brunck@keymile.com>
	* Christian Herzig, Keymile AG Switzerland, <christian.herzig@keymile.com>
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/* KMBEC FPGA (PRIO) */
	#define CONFIG_SYS_KMBEC_FPGA_BASE 0xE8000000
	#define CONFIG_SYS_KMBEC_FPGA_SIZE 64

	#define CONFIG_HOSTNAME "kmcoge5ne"
	#define CONFIG_KM_BOARD_NAME "kmcoge5ne"
	#define CONFIG_KM_DEF_NETDEV "netdev=eth1\0"
	#define CONFIG_NAND_ECC_BCH
	#define CONFIG_NAND_KMETER1
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define NAND_MAX_CHIPS 1
	#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */

	#define CONFIG_KM_UBI_PARTITION_NAME_BOOT "ubi0"
	#define CONFIG_KM_UBI_PARTITION_NAME_APP "ubi1"

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_QE /* Has QE */

	/* include common defines/options for all Keymile boards */
	#include "km/keymile-common.h"
	#include "km/km-powerpc.h"

	/*
	* System Clock Setup
	*/
	#define CONFIG_83XX_CLKIN 66000000
	#define CONFIG_SYS_CLK_FREQ 66000000
	#define CONFIG_83XX_PCICLK 66000000

	/*
	* IMMR new address
	*/
	#define CONFIG_SYS_IMMR 0xE0000000

	/*
	* Bus Arbitration Configuration Register (ACR)
	*/
	#define CONFIG_SYS_ACR_PIPE_DEP 3 /* pipeline depth 4 transactions */
	#define CONFIG_SYS_ACR_RPTCNT 3 /* 4 consecutive transactions */
	#define CONFIG_SYS_ACR_APARK 0 /* park bus to master (below) */
	#define CONFIG_SYS_ACR_PARKM 3 /* parking master = QuiccEngine */

	/*
	* DDR Setup
	*/
	#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
	#define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */

	#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
	#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \| \
	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)

	#define CFG_83XX_DDR_USES_CS0

	/*
	* Manually set up DDR parameters
	*/
	#define CONFIG_DDR_II
	#define CONFIG_SYS_DDR_SIZE 2048 /* MB */

	/*
	* The reserved memory
	*/
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
	#define CONFIG_SYS_FLASH_BASE 0xF0000000

	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	#define CONFIG_SYS_RAMBOOT
	#endif

	/* Reserve 768 kB for Mon */
	#define CONFIG_SYS_MONITOR_LEN (768 * 1024)

	/*
	* Initial RAM Base Address Setup
	*/
	#define CONFIG_SYS_INIT_RAM_LOCK
	#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
	GENERATED_GBL_DATA_SIZE)

	/*
	* Init Local Bus Memory Controller:
	*
	* Bank Bus Machine PortSz Size Device
	* ---- --- ------- ------ ----- ------
	* 0 Local GPCM 16 bit 256MB FLASH
	* 1 Local GPCM 8 bit 128MB GPIO/PIGGY
	*
	*/
	/*
	* FLASH on the Local Bus
	*/
	#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */

	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \| \
	BR_PS_16 \| /* 16 bit port size */ \
	BR_MS_GPCM \| /* MSEL = GPCM */ \
	BR_V)

	#define CONFIG_SYS_OR0_PRELIM (OR_AM_256MB \| \
	OR_GPCM_CSNT \| OR_GPCM_ACS_DIV2 \| \
	OR_GPCM_SCY_5 \| \
	OR_GPCM_TRLX_SET \| OR_GPCM_EAD)

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }

	/*
	* PRIO1/PIGGY on the local bus CS1
	*/
	/* Window base at flash base */
	#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_KMBEC_FPGA_BASE \| \
	BR_PS_8 \| /* 8 bit port size */ \
	BR_MS_GPCM \| /* MSEL = GPCM */ \
	BR_V)
	#define CONFIG_SYS_OR1_PRELIM (OR_AM_64MB \| \
	OR_GPCM_CSNT \| OR_GPCM_ACS_DIV2 \| \
	OR_GPCM_SCY_2 \| \
	OR_GPCM_TRLX_SET \| OR_GPCM_EAD)

	/*
	* Serial Port
	*/
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)

	/*
	* QE UEC ethernet configuration
	*/
	#define CONFIG_UEC_ETH
	#define CONFIG_ETHPRIME "UEC0"

	#define CONFIG_UEC_ETH1 /* GETH1 */
	#define UEC_VERBOSE_DEBUG 1

	#ifdef CONFIG_UEC_ETH1
	#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
	#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
	#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
	#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
	#define CONFIG_SYS_UEC1_PHY_ADDR 0
	#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
	#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
	#endif

	/*
	* Environment
	*/

	#ifndef CONFIG_SYS_RAMBOOT
	#ifndef CONFIG_ENV_ADDR
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
	CONFIG_SYS_MONITOR_LEN)
	#endif
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
	#ifndef CONFIG_ENV_OFFSET
	#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
	#endif

	/* Address and size of Redundant Environment Sector */
	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
	CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)

	#else /* CFG_SYS_RAMBOOT */
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
	#define CONFIG_ENV_SIZE 0x2000
	#endif /* CFG_SYS_RAMBOOT */

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_NUM_I2C_BUSES 4
	#define CONFIG_SYS_I2C_MAX_HOPS 1
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 200000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	#define CONFIG_SYS_I2C_OFFSET 0x3000
	#define CONFIG_SYS_FSL_I2C2_SPEED 200000
	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
	#define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \
	{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
	{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
	{1, {I2C_NULL_HOP} } }

	#define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/

	#if defined(CONFIG_CMD_NAND)
	#define CONFIG_NAND_KMETER1
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE
	#endif

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20)

	/*
	* Core HID Setup
	*/
	#define CONFIG_SYS_HID0_INIT 0x000000000
	#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK \| \
	HID0_ENABLE_INSTRUCTION_CACHE)
	#define CONFIG_SYS_HID2 HID2_HBE

	/*
	* Internal Definitions
	*/
	#define BOOTFLASH_START 0xF0000000

	#define CONFIG_KM_CONSOLE_TTY "ttyS0"

	/*
	* Environment Configuration
	*/
	#define CONFIG_ENV_OVERWRITE
	#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
	#define CONFIG_KM_DEF_ENV "km-common=empty\0"
	#endif

	#ifndef CONFIG_KM_DEF_ARCH
	#define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0"
	#endif

	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_KM_DEF_ENV \
	CONFIG_KM_DEF_ARCH \
	"newenv=" \
	"prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \
	"era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \
	"unlock=yes\0" \
	""

	#if defined(CONFIG_UEC_ETH)
	#define CONFIG_HAS_ETH0
	#endif

	/*
	* System IO Setup
	*/
	#define CONFIG_SYS_SICRH (SICRH_UC1EOBI \| SICRH_UC2E1OBI)

	/**
	* DDR RAM settings
	*/
	#define CONFIG_SYS_DDR_SDRAM_CFG (\
	SDRAM_CFG_SDRAM_TYPE_DDR2 \| \
	SDRAM_CFG_SREN \| \
	SDRAM_CFG_HSE)

	#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000

	/**
	* KMCOGE5NE has 512 MB RAM
	*/
	#define CONFIG_SYS_DDR_CS0_CONFIG (\
	CSCONFIG_EN \| \
	CSCONFIG_AP \| \
	CSCONFIG_ODT_WR_ONLY_CURRENT \| \
	CSCONFIG_BANK_BIT_3 \| \
	CSCONFIG_ROW_BIT_13 \| \
	CSCONFIG_COL_BIT_10)

	#define CONFIG_SYS_DDR_CLK_CNTL (\
	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)

	#define CONFIG_SYS_DDR_INTERVAL (\
	(0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) \| \
	(0x203 << SDRAM_INTERVAL_REFINT_SHIFT))

	#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f

	#define CONFIG_SYS_DDRCDR (\
	DDRCDR_EN \| \
	DDRCDR_Q_DRN)
	#define CONFIG_SYS_DDR_MODE 0x47860452
	#define CONFIG_SYS_DDR_MODE2 0x8080c000

	#define CONFIG_SYS_DDR_TIMING_0 (\
	(2 << TIMING_CFG0_MRS_CYC_SHIFT) \| \
	(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \| \
	(6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \| \
	(2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \| \
	(0 << TIMING_CFG0_WWT_SHIFT) \| \
	(0 << TIMING_CFG0_RRT_SHIFT) \| \
	(0 << TIMING_CFG0_WRT_SHIFT) \| \
	(0 << TIMING_CFG0_RWT_SHIFT))

	#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_50) \| \
	(2 << TIMING_CFG1_WRTORD_SHIFT) \| \
	(2 << TIMING_CFG1_ACTTOACT_SHIFT) \| \
	(3 << TIMING_CFG1_WRREC_SHIFT) \| \
	(7 << TIMING_CFG1_REFREC_SHIFT) \| \
	(3 << TIMING_CFG1_ACTTORW_SHIFT) \| \
	(8 << TIMING_CFG1_ACTTOPRE_SHIFT) \| \
	(3 << TIMING_CFG1_PRETOACT_SHIFT))

	#define CONFIG_SYS_DDR_TIMING_2 (\
	(0xa << TIMING_CFG2_FOUR_ACT_SHIFT) \| \
	(3 << TIMING_CFG2_CKE_PLS_SHIFT) \| \
	(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \| \
	(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \| \
	(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \| \
	(5 << TIMING_CFG2_CPO_SHIFT) \| \
	(0 << TIMING_CFG2_ADD_LAT_SHIFT))

	#define CONFIG_SYS_DDR_TIMING_3 0x00000000

	/* EEprom support */
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2

	/*
	* Local Bus Configuration & Clock Setup
	*/
	#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP
	#define CONFIG_SYS_LCRR_EADC LCRR_EADC_2
	#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4

	/*
	* PAXE on the local bus CS3
	*/
	#define CONFIG_SYS_PAXE_BASE 0xA0000000
	#define CONFIG_SYS_PAXE_SIZE 256

	#define CONFIG_SYS_BR3_PRELIM (\
	CONFIG_SYS_PAXE_BASE \| \
	BR_PS_8 \| \
	BR_V)

	#define CONFIG_SYS_OR3_PRELIM (\
	OR_AM_256MB \| \
	OR_GPCM_CSNT \| \
	OR_GPCM_ACS_DIV2 \| \
	OR_GPCM_SCY_2 \| \
	OR_GPCM_TRLX \| \
	OR_GPCM_EAD)

	/*
	* BFTIC3 on the local bus CS4
	*/
	#define CONFIG_SYS_BFTIC3_BASE 0xB0000000
	#define CONFIG_SYS_BFTIC3_SIZE 256

	#define CONFIG_SYS_BR4_PRELIM (\
	CONFIG_SYS_BFTIC3_BASE \|\
	BR_PS_8 \| \
	BR_V)

	#define CONFIG_SYS_OR4_PRELIM (\
	OR_AM_256MB\|\
	OR_GPCM_CSNT \| \
	OR_GPCM_ACS_DIV2 \|\
	OR_GPCM_SCY_2 \|\
	OR_GPCM_TRLX \|\
	OR_GPCM_EAD)

	/* enable POST tests */
	#define CONFIG_POST (CONFIG_SYS_POST_MEMORY\|CONFIG_SYS_POST_MEM_REGIONS)
	#define CONFIG_POST_EXTERNAL_WORD_FUNCS /* use own functions, not generic */
	#define CPM_POST_WORD_ADDR CONFIG_SYS_MEMTEST_END
	#define CONFIG_TESTPIN_REG gprt3 /* for kmcoge5ne */
	#define CONFIG_TESTPIN_MASK 0x20 /* for kmcoge5ne */

	#endif /* CONFIG */