blob: 4c2f990b28782ef1628a99f66392cb19e61f8b92 [file] [log] [blame]
if OMAP54XX
config DRA7XX
bool
help
DRA7xx is an OMAP based SOC with Dual Core A-15s.
choice
prompt "OMAP5 board select"
optional
config TARGET_CM_T54
bool "CompuLab CM-T54"
config TARGET_OMAP5_UEVM
bool "TI OMAP5 uEVM board"
config TARGET_DRA7XX_EVM
bool "TI DRA7XX"
select BOARD_LATE_INIT
select DRA7XX
select PHYS_64BIT
select TI_I2C_BOARD_DETECT
imply DM_PMIC
imply DM_REGULATOR
imply DM_REGULATOR_LP87565
imply DM_THERMAL
imply PMIC_LP87565
imply SCSI
imply SPL_THERMAL
imply TI_DRA7_THERMAL
config TARGET_AM57XX_EVM
bool "AM57XX"
select BOARD_LATE_INIT
select CMD_DDR3
select DRA7XX
select TI_I2C_BOARD_DETECT
select SUPPORT_EXTENSION_SCAN
imply DM_THERMAL
imply SCSI
imply SPL_THERMAL
imply TI_DRA7_THERMAL
endchoice
config SYS_SOC
default "omap5"
config OMAP_PLATFORM_RESET_TIME_MAX_USEC
int "Something"
range 0 31219
default 31219
help
Most OMAPs' provide a way to specify the time for which the reset
should be held low while the voltages and Oscillator outputs
stabilize.
This time is mostly board and PMIC dependent. Hence the boards are
expected to specify a pre-computed time using the above option.
This value can be computed using a summation of the below 3
parameters
1: Time taken by the Osciallator to stop and restart
2: PMIC OTP time
3: Voltage ramp time, which can be derived using the PMIC slew rate
and value of voltage ramp needed.
if TARGET_DRA7XX_EVM || TARGET_AM57XX_EVM
menu "Voltage Domain OPP selections"
choice
prompt "MPU Voltage Domain"
default DRA7_MPU_OPP_NOM
help
Select the Operating Performance Point(OPP) for the MPU voltage
domain on DRA7xx & AM57xx SoCs.
config DRA7_MPU_OPP_NOM
bool "OPP NOM"
help
This config option enables Normal OPP for MPU. This is the safest
option for booting.
endchoice
choice
prompt "DSPEVE Voltage Domain"
help
Select the Operating Performance Point(OPP) for the DSPEVE voltage
domain on DRA7xx & AM57xx SoCs.
config DRA7_DSPEVE_OPP_NOM
bool "OPP NOM"
help
This config option enables Normal OPP for DSPEVE. This is the safest
option for booting and choose this when unsure about other OPPs .
config DRA7_DSPEVE_OPP_OD
bool "OPP OD"
help
This config option enables Over drive OPP for DSPEVE.
config DRA7_DSPEVE_OPP_HIGH
bool "OPP HIGH"
help
This config option enables High OPP for DSPEVE.
endchoice
choice
prompt "IVA Voltage Domain"
help
Select the Operating Performance Point(OPP) for the IVA voltage
domain on DRA7xx & AM57xx SoCs.
config DRA7_IVA_OPP_NOM
bool "OPP NOM"
help
This config option enables Normal OPP for IVA. This is the safest
option for booting and choose this when unsure about other OPPs .
config DRA7_IVA_OPP_OD
bool "OPP OD"
help
This config option enables Over drive OPP for IVA.
config DRA7_IVA_OPP_HIGH
bool "OPP HIGH"
help
This config option enables High OPP for IVA.
endchoice
choice
prompt "GPU Voltage Domain"
help
Select the Operating Performance Point(OPP) for the GPU voltage
domain on DRA7xx & AM57xx SoCs.
config DRA7_GPU_OPP_NOM
bool "OPP NOM"
help
This config option enables Normal OPP for GPU. This is the safest
option for booting and choose this when unsure about other OPPs .
config DRA7_GPU_OPP_OD
bool "OPP OD"
help
This config option enables Over drive OPP for GPU.
config DRA7_GPU_OPP_HIGH
bool "OPP HIGH"
help
This config option enables High OPP for GPU.
endchoice
endmenu
endif
source "board/ti/omap5_uevm/Kconfig"
source "board/ti/dra7xx/Kconfig"
source "board/ti/am57xx/Kconfig"
endif