| /* |
| * (C) Copyright 2010 |
| * Heiko Schocher, DENX Software Engineering, hs@denx.de. |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __CONFIG_KM83XX_H |
| #define __CONFIG_KM83XX_H |
| |
| /* include common defines/options for all Keymile boards */ |
| #include "keymile-common.h" |
| #include "km-powerpc.h" |
| |
| #ifndef MTDIDS_DEFAULT |
| # define MTDIDS_DEFAULT "nor0=boot" |
| #endif /* MTDIDS_DEFAULT */ |
| |
| #ifndef MTDPARTS_DEFAULT |
| # define MTDPARTS_DEFAULT "mtdparts=" \ |
| "boot:" \ |
| "768k(u-boot)," \ |
| "128k(env)," \ |
| "128k(envred)," \ |
| "-(" CONFIG_KM_UBI_PARTITION_NAME_BOOT ");" |
| #endif /* MTDPARTS_DEFAULT */ |
| |
| #define CONFIG_MISC_INIT_R |
| /* |
| * System Clock Setup |
| */ |
| #define CONFIG_83XX_CLKIN 66000000 |
| #define CONFIG_SYS_CLK_FREQ 66000000 |
| #define CONFIG_83XX_PCICLK 66000000 |
| |
| /* |
| * IMMR new address |
| */ |
| #define CONFIG_SYS_IMMR 0xE0000000 |
| |
| /* |
| * Bus Arbitration Configuration Register (ACR) |
| */ |
| #define CONFIG_SYS_ACR_PIPE_DEP 3 /* pipeline depth 4 transactions */ |
| #define CONFIG_SYS_ACR_RPTCNT 3 /* 4 consecutive transactions */ |
| #define CONFIG_SYS_ACR_APARK 0 /* park bus to master (below) */ |
| #define CONFIG_SYS_ACR_PARKM 3 /* parking master = QuiccEngine */ |
| |
| /* |
| * DDR Setup |
| */ |
| #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_SDRAM_BASE2 (CONFIG_SYS_SDRAM_BASE + 0x10000000) /* +256M */ |
| |
| #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE |
| #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ |
| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) |
| |
| #define CFG_83XX_DDR_USES_CS0 |
| |
| /* |
| * Manually set up DDR parameters |
| */ |
| #define CONFIG_DDR_II |
| #define CONFIG_SYS_DDR_SIZE 2048 /* MB */ |
| |
| /* |
| * The reserved memory |
| */ |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ |
| #define CONFIG_SYS_FLASH_BASE 0xF0000000 |
| |
| #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) |
| #define CONFIG_SYS_RAMBOOT |
| #endif |
| |
| /* Reserve 768 kB for Mon */ |
| #define CONFIG_SYS_MONITOR_LEN (768 * 1024) |
| |
| /* |
| * Initial RAM Base Address Setup |
| */ |
| #define CONFIG_SYS_INIT_RAM_LOCK |
| #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ |
| #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* End of used area in RAM */ |
| #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ |
| GENERATED_GBL_DATA_SIZE) |
| |
| /* |
| * Init Local Bus Memory Controller: |
| * |
| * Bank Bus Machine PortSz Size Device |
| * ---- --- ------- ------ ----- ------ |
| * 0 Local GPCM 16 bit 256MB FLASH |
| * 1 Local GPCM 8 bit 128MB GPIO/PIGGY |
| * |
| */ |
| /* |
| * FLASH on the Local Bus |
| */ |
| #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ |
| #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ |
| #define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ |
| #define CONFIG_SYS_FLASH_PROTECTION |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| |
| #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_256MB) |
| |
| #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ |
| BR_PS_16 | /* 16 bit port size */ \ |
| BR_MS_GPCM | /* MSEL = GPCM */ \ |
| BR_V) |
| |
| #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \ |
| OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ |
| OR_GPCM_SCY_5 | \ |
| OR_GPCM_TRLX_SET | OR_GPCM_EAD) |
| |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } |
| |
| /* |
| * PRIO1/PIGGY on the local bus CS1 |
| */ |
| /* Window base at flash base */ |
| #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_KMBEC_FPGA_BASE |
| #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_128MB) |
| |
| #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_KMBEC_FPGA_BASE | \ |
| BR_PS_8 | /* 8 bit port size */ \ |
| BR_MS_GPCM | /* MSEL = GPCM */ \ |
| BR_V) |
| #define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_KMBEC_FPGA_SIZE) | \ |
| OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ |
| OR_GPCM_SCY_2 | \ |
| OR_GPCM_TRLX_SET | OR_GPCM_EAD) |
| |
| /* |
| * Serial Port |
| */ |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) |
| |
| #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) |
| #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) |
| |
| /* |
| * QE UEC ethernet configuration |
| */ |
| #define CONFIG_UEC_ETH |
| #define CONFIG_ETHPRIME "UEC0" |
| |
| #if !defined(CONFIG_MPC8309) |
| #define CONFIG_UEC_ETH1 /* GETH1 */ |
| #define UEC_VERBOSE_DEBUG 1 |
| #endif |
| |
| #ifdef CONFIG_UEC_ETH1 |
| #define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ |
| #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ |
| #define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 |
| #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH |
| #define CONFIG_SYS_UEC1_PHY_ADDR 0 |
| #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII |
| #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 |
| #endif |
| |
| /* |
| * Environment |
| */ |
| |
| #ifndef CONFIG_SYS_RAMBOOT |
| #ifndef CONFIG_ENV_ADDR |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \ |
| CONFIG_SYS_MONITOR_LEN) |
| #endif |
| #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ |
| #ifndef CONFIG_ENV_OFFSET |
| #define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) |
| #endif |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \ |
| CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| |
| #else /* CFG_SYS_RAMBOOT */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) |
| #define CONFIG_ENV_SIZE 0x2000 |
| #endif /* CFG_SYS_RAMBOOT */ |
| |
| /* I2C */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_NUM_I2C_BUSES 4 |
| #define CONFIG_SYS_I2C_MAX_HOPS 1 |
| #define CONFIG_SYS_I2C_FSL |
| #define CONFIG_SYS_FSL_I2C_SPEED 200000 |
| #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_I2C_OFFSET 0x3000 |
| #define CONFIG_SYS_FSL_I2C2_SPEED 200000 |
| #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F |
| #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 |
| #define CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP} }, \ |
| {0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \ |
| {0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \ |
| {1, {I2C_NULL_HOP} } } |
| |
| #define CONFIG_KM_IVM_BUS 2 /* I2C2 (Mux-Port 1)*/ |
| |
| #if defined(CONFIG_CMD_NAND) |
| #define CONFIG_NAND_KMETER1 |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 |
| #define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE |
| #endif |
| |
| /* |
| * For booting Linux, the board info and command line data |
| * have to be in the first 8 MB of memory, since this is |
| * the maximum mapped by the Linux kernel during initialization. |
| */ |
| #define CONFIG_SYS_BOOTMAPSZ (8 << 20) |
| |
| /* |
| * Core HID Setup |
| */ |
| #define CONFIG_SYS_HID0_INIT 0x000000000 |
| #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ |
| HID0_ENABLE_INSTRUCTION_CACHE) |
| #define CONFIG_SYS_HID2 HID2_HBE |
| |
| /* |
| * MMU Setup |
| */ |
| |
| #define CONFIG_HIGH_BATS 1 /* High BATs supported */ |
| |
| /* DDR: cache cacheable */ |
| #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \ |
| BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L |
| #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U |
| |
| /* IMMRBAR & PCI IO: cache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_RW | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS \ |
| | BATU_VP) |
| #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L |
| #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U |
| |
| /* PRIO1, PIGGY: icache cacheable, but dcache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT2L (CONFIG_SYS_KMBEC_FPGA_BASE | BATL_PP_RW | \ |
| BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT2U (CONFIG_SYS_KMBEC_FPGA_BASE | BATU_BL_128M | \ |
| BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT2L (CONFIG_SYS_KMBEC_FPGA_BASE | BATL_PP_RW | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U |
| |
| /* FLASH: icache cacheable, but dcache-inhibit and guarded */ |
| #define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ |
| BATL_MEMCOHERENCE) |
| #define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | \ |
| BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | \ |
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) |
| #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U |
| |
| /* Stack in dcache: cacheable, no memory coherence */ |
| #define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW) |
| #define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \ |
| BATU_VS | BATU_VP) |
| #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L |
| #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U |
| |
| /* |
| * Internal Definitions |
| */ |
| #define BOOTFLASH_START 0xF0000000 |
| |
| #define CONFIG_KM_CONSOLE_TTY "ttyS0" |
| |
| /* |
| * Environment Configuration |
| */ |
| #define CONFIG_ENV_OVERWRITE |
| #ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ |
| #define CONFIG_KM_DEF_ENV "km-common=empty\0" |
| #endif |
| |
| #ifndef CONFIG_KM_DEF_ARCH |
| #define CONFIG_KM_DEF_ARCH "arch=ppc_82xx\0" |
| #endif |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| CONFIG_KM_DEF_ENV \ |
| CONFIG_KM_DEF_ARCH \ |
| "newenv=" \ |
| "prot off "__stringify(CONFIG_ENV_ADDR)" +0x40000 && " \ |
| "era "__stringify(CONFIG_ENV_ADDR)" +0x40000\0" \ |
| "unlock=yes\0" \ |
| "" |
| |
| #if defined(CONFIG_UEC_ETH) |
| #define CONFIG_HAS_ETH0 |
| #endif |
| |
| #endif /* __CONFIG_KM83XX_H */ |