| /* |
| * Copyright (C) 2015 Freescale Semiconductor |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __LS1043A_COMMON_H |
| #define __LS1043A_COMMON_H |
| |
| /* SPL build */ |
| #ifdef CONFIG_SPL_BUILD |
| #define SPL_NO_FMAN |
| #define SPL_NO_DSPI |
| #define SPL_NO_PCIE |
| #define SPL_NO_ENV |
| #define SPL_NO_MISC |
| #define SPL_NO_USB |
| #define SPL_NO_SATA |
| #define SPL_NO_QE |
| #define SPL_NO_EEPROM |
| #endif |
| #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_NAND_BOOT)) |
| #define SPL_NO_MMC |
| #endif |
| #if (defined(CONFIG_SPL_BUILD) && defined(CONFIG_SD_BOOT_QSPI)) |
| #define SPL_NO_IFC |
| #endif |
| |
| #define CONFIG_REMAKE_ELF |
| #define CONFIG_FSL_LAYERSCAPE |
| #define CONFIG_MP |
| #define CONFIG_GICV2 |
| |
| #include <asm/arch/stream_id_lsch2.h> |
| #include <asm/arch/config.h> |
| |
| /* Link Definitions */ |
| #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0) |
| |
| #define CONFIG_SUPPORT_RAW_INITRD |
| |
| #define CONFIG_SKIP_LOWLEVEL_INIT |
| |
| #define CONFIG_VERY_BIG_RAM |
| #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000 |
| #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 |
| #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE |
| #define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL |
| |
| #define CPU_RELEASE_ADDR secondary_boot_func |
| |
| /* Generic Timer Definitions */ |
| #define COUNTER_FREQUENCY 25000000 /* 25MHz */ |
| |
| /* Size of malloc() pool */ |
| #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024) |
| |
| /* Serial Port */ |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE 1 |
| #define CONFIG_SYS_NS16550_CLK (get_serial_clock()) |
| |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| |
| /* SD boot SPL */ |
| #ifdef CONFIG_SD_BOOT |
| #define CONFIG_SPL_FRAMEWORK |
| #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" |
| |
| #define CONFIG_SPL_TEXT_BASE 0x10000000 |
| #define CONFIG_SPL_MAX_SIZE 0x17000 |
| #define CONFIG_SPL_STACK 0x1001e000 |
| #define CONFIG_SPL_PAD_TO 0x1d000 |
| |
| #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SYS_TEXT_BASE + \ |
| CONFIG_SYS_MONITOR_LEN) |
| #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 |
| #define CONFIG_SPL_BSS_START_ADDR 0x80100000 |
| #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 |
| |
| #ifdef CONFIG_SECURE_BOOT |
| #define CONFIG_U_BOOT_HDR_SIZE (16 << 10) |
| /* |
| * HDR would be appended at end of image and copied to DDR along |
| * with U-Boot image. Here u-boot max. size is 512K. So if binary |
| * size increases then increase this size in case of secure boot as |
| * it uses raw u-boot image instead of fit image. |
| */ |
| #define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE) |
| #else |
| #define CONFIG_SYS_MONITOR_LEN 0x100000 |
| #endif /* ifdef CONFIG_SECURE_BOOT */ |
| #endif |
| |
| /* NAND SPL */ |
| #ifdef CONFIG_NAND_BOOT |
| #define CONFIG_SPL_PBL_PAD |
| #define CONFIG_SPL_FRAMEWORK |
| #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" |
| #define CONFIG_SPL_TEXT_BASE 0x10000000 |
| #define CONFIG_SPL_MAX_SIZE 0x1a000 |
| #define CONFIG_SPL_STACK 0x1001d000 |
| #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_SPL_MALLOC_START 0x80200000 |
| #define CONFIG_SPL_BSS_START_ADDR 0x80100000 |
| #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 |
| #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 |
| |
| #ifdef CONFIG_SECURE_BOOT |
| #define CONFIG_U_BOOT_HDR_SIZE (16 << 10) |
| #endif /* ifdef CONFIG_SECURE_BOOT */ |
| |
| #ifdef CONFIG_U_BOOT_HDR_SIZE |
| /* |
| * HDR would be appended at end of image and copied to DDR along |
| * with U-Boot image. Here u-boot max. size is 512K. So if binary |
| * size increases then increase this size in case of secure boot as |
| * it uses raw u-boot image instead of fit image. |
| */ |
| #define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE) |
| #else |
| #define CONFIG_SYS_MONITOR_LEN 0x100000 |
| #endif /* ifdef CONFIG_U_BOOT_HDR_SIZE */ |
| |
| #endif |
| |
| /* IFC */ |
| #ifndef SPL_NO_IFC |
| #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_FSL_IFC |
| /* |
| * CONFIG_SYS_FLASH_BASE has the final address (core view) |
| * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view) |
| * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address |
| * CONFIG_SYS_TEXT_BASE is linked to 0x60000000 for booting |
| */ |
| #define CONFIG_SYS_FLASH_BASE 0x60000000 |
| #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE |
| #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000 |
| |
| #ifdef CONFIG_MTD_NOR_FLASH |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE |
| #define CONFIG_SYS_FLASH_QUIET_TEST |
| #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ |
| #endif |
| #endif |
| #endif |
| |
| /* I2C */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_MXC |
| #define CONFIG_SYS_I2C_MXC_I2C1 |
| #define CONFIG_SYS_I2C_MXC_I2C2 |
| #define CONFIG_SYS_I2C_MXC_I2C3 |
| #define CONFIG_SYS_I2C_MXC_I2C4 |
| |
| /* PCIe */ |
| #ifndef SPL_NO_PCIE |
| #define CONFIG_PCIE1 /* PCIE controller 1 */ |
| #define CONFIG_PCIE2 /* PCIE controller 2 */ |
| #define CONFIG_PCIE3 /* PCIE controller 3 */ |
| |
| #ifdef CONFIG_PCI |
| #define CONFIG_NET_MULTI |
| #define CONFIG_PCI_SCAN_SHOW |
| #endif |
| #endif |
| |
| /* Command line configuration */ |
| |
| /* MMC */ |
| #ifndef SPL_NO_MMC |
| #ifdef CONFIG_MMC |
| #define CONFIG_FSL_ESDHC |
| #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 |
| #endif |
| #endif |
| |
| /* DSPI */ |
| #ifndef SPL_NO_DSPI |
| #define CONFIG_FSL_DSPI |
| #ifdef CONFIG_FSL_DSPI |
| #define CONFIG_DM_SPI_FLASH |
| #define CONFIG_SPI_FLASH_STMICRO /* cs0 */ |
| #define CONFIG_SPI_FLASH_SST /* cs1 */ |
| #define CONFIG_SPI_FLASH_EON /* cs2 */ |
| #if !defined(CONFIG_QSPI_BOOT) && !defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_SF_DEFAULT_BUS 1 |
| #define CONFIG_SF_DEFAULT_CS 0 |
| #endif |
| #endif |
| #endif |
| |
| /* FMan ucode */ |
| #ifndef SPL_NO_FMAN |
| #define CONFIG_SYS_DPAA_FMAN |
| #ifdef CONFIG_SYS_DPAA_FMAN |
| #define CONFIG_SYS_FM_MURAM_SIZE 0x60000 |
| |
| #ifdef CONFIG_NAND_BOOT |
| /* Store Fman ucode at offeset 0x900000(72 blocks). */ |
| #define CONFIG_SYS_QE_FMAN_FW_IN_NAND |
| #define CONFIG_SYS_FMAN_FW_ADDR (72 * CONFIG_SYS_NAND_BLOCK_SIZE) |
| #elif defined(CONFIG_SD_BOOT) |
| /* |
| * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is |
| * about 1MB (2040 blocks), Env is stored after the image, and the env size is |
| * 0x2000 (16 blocks), 8 + 2040 + 16 = 2064, enlarge it to 18432(0x4800). |
| */ |
| #define CONFIG_SYS_QE_FMAN_FW_IN_MMC |
| #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x4800) |
| #define CONFIG_SYS_QE_FW_ADDR (512 * 0x4a08) |
| #elif defined(CONFIG_QSPI_BOOT) |
| #define CONFIG_SYS_QE_FW_IN_SPIFLASH |
| #define CONFIG_SYS_FMAN_FW_ADDR 0x40900000 |
| #define CONFIG_ENV_SPI_BUS 0 |
| #define CONFIG_ENV_SPI_CS 0 |
| #define CONFIG_ENV_SPI_MAX_HZ 1000000 |
| #define CONFIG_ENV_SPI_MODE 0x03 |
| #else |
| #define CONFIG_SYS_QE_FMAN_FW_IN_NOR |
| /* FMan fireware Pre-load address */ |
| #define CONFIG_SYS_FMAN_FW_ADDR 0x60900000 |
| #define CONFIG_SYS_QE_FW_ADDR 0x60940000 |
| #endif |
| #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 |
| #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) |
| #endif |
| #endif |
| |
| /* Miscellaneous configurable options */ |
| #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) |
| |
| #define CONFIG_HWCONFIG |
| #define HWCONFIG_BUFFER_SIZE 128 |
| |
| #ifndef SPL_NO_MISC |
| #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) |
| #define MTDPARTS_DEFAULT "mtdparts=spi0.0:1m(uboot)," \ |
| "5m(kernel),1m(dtb),9m(file_system)" |
| #else |
| #define MTDPARTS_DEFAULT "mtdparts=60000000.nor:" \ |
| "2m@0x100000(nor_bank0_uboot),"\ |
| "40m@0x1100000(nor_bank0_fit)," \ |
| "7m(nor_bank0_user)," \ |
| "2m@0x4100000(nor_bank4_uboot)," \ |
| "40m@0x5100000(nor_bank4_fit),"\ |
| "-(nor_bank4_user);" \ |
| "7e800000.flash:" \ |
| "1m(nand_uboot),1m(nand_uboot_env)," \ |
| "20m(nand_fit);spi0.0:1m(uboot)," \ |
| "5m(kernel),1m(dtb),9m(file_system)" |
| #endif |
| |
| #include <config_distro_defaults.h> |
| #ifndef CONFIG_SPL_BUILD |
| #define BOOT_TARGET_DEVICES(func) \ |
| func(MMC, mmc, 0) \ |
| func(USB, usb, 0) |
| #include <config_distro_bootcmd.h> |
| #endif |
| |
| /* Initial environment variables */ |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "hwconfig=fsl_ddr:bank_intlv=auto\0" \ |
| "fdt_high=0xffffffffffffffff\0" \ |
| "initrd_high=0xffffffffffffffff\0" \ |
| "fdt_addr=0x64f00000\0" \ |
| "kernel_addr=0x65000000\0" \ |
| "scriptaddr=0x80000000\0" \ |
| "scripthdraddr=0x80080000\0" \ |
| "fdtheader_addr_r=0x80100000\0" \ |
| "kernelheader_addr_r=0x80200000\0" \ |
| "kernel_addr_r=0x81000000\0" \ |
| "fdt_addr_r=0x90000000\0" \ |
| "load_addr=0xa0000000\0" \ |
| "kernel_size=0x2800000\0" \ |
| "console=ttyS0,115200\0" \ |
| "mtdparts=" MTDPARTS_DEFAULT "\0" \ |
| BOOTENV \ |
| "boot_scripts=ls1043ardb_boot.scr\0" \ |
| "boot_script_hdr=hdr_ls1043ardb_bs.out\0" \ |
| "scan_dev_for_boot_part=" \ |
| "part list ${devtype} ${devnum} devplist; " \ |
| "env exists devplist || setenv devplist 1; " \ |
| "for distro_bootpart in ${devplist}; do " \ |
| "if fstype ${devtype} " \ |
| "${devnum}:${distro_bootpart} " \ |
| "bootfstype; then " \ |
| "run scan_dev_for_boot; " \ |
| "fi; " \ |
| "done\0" \ |
| "scan_dev_for_boot=" \ |
| "echo Scanning ${devtype} " \ |
| "${devnum}:${distro_bootpart}...; " \ |
| "for prefix in ${boot_prefixes}; do " \ |
| "run scan_dev_for_scripts; " \ |
| "done;\0" \ |
| "boot_a_script=" \ |
| "load ${devtype} ${devnum}:${distro_bootpart} " \ |
| "${scriptaddr} ${prefix}${script}; " \ |
| "env exists secureboot && load ${devtype} " \ |
| "${devnum}:${distro_bootpart} " \ |
| "${scripthdraddr} ${prefix}${boot_script_hdr} " \ |
| "&& esbc_validate ${scripthdraddr};" \ |
| "source ${scriptaddr}\0" \ |
| "installer=load mmc 0:2 $load_addr " \ |
| "/flex_installer_arm64.itb; " \ |
| "bootm $load_addr#ls1043ardb\0" \ |
| "qspi_bootcmd=echo Trying load from qspi..;" \ |
| "sf probe && sf read $load_addr " \ |
| "$kernel_addr $kernel_size && bootm $load_addr#$board\0" \ |
| "nor_bootcmd=echo Trying load from nor..;" \ |
| "cp.b $kernel_addr $load_addr " \ |
| "$kernel_size && bootm $load_addr#$board\0" |
| |
| #undef CONFIG_BOOTCOMMAND |
| #if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) |
| #define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot" \ |
| "&& esbc_halt; run qspi_bootcmd;" |
| #else |
| #define CONFIG_BOOTCOMMAND "run distro_bootcmd; env exists secureboot" \ |
| "&& esbc_halt; run nor_bootcmd;" |
| #endif |
| #endif |
| |
| /* Monitor Command Prompt */ |
| #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_LONGHELP |
| |
| #ifndef SPL_NO_MISC |
| #ifndef CONFIG_CMDLINE_EDITING |
| #define CONFIG_CMDLINE_EDITING 1 |
| #endif |
| #endif |
| |
| #define CONFIG_AUTO_COMPLETE |
| #define CONFIG_SYS_MAXARGS 64 /* max command args */ |
| |
| #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ |
| |
| #include <asm/arch/soc.h> |
| |
| #endif /* __LS1043A_COMMON_H */ |